Hi Antti,
On Friday 11 Nov 2016 09:16:04 Antti Palosaari wrote:
> Hello
>
> On 11/09/2016 05:44 PM, Ramesh Shanmugasundaram wrote:
> > +static int max2175_set_lo_freq(struct max2175 *ctx, u64 lo_freq)
> > +{
> > + u64 scaled_lo_freq, scaled_npf, scaled_integer, scaled_fraction;
> > + u32 frac_desired, int_desired, lo_mult = 1;
> > + const u32 scale_factor = 1000000U;
> > + u8 loband_bits = 0, vcodiv_bits = 0;
> > + enum max2175_band band;
> > + int ret;
> > +
> > + /* Scale to larger number for precision */
> > + scaled_lo_freq = lo_freq * scale_factor * 100;
> > + band = max2175_read_bits(ctx, 5, 1, 0);
> > +
> > + mxm_dbg(ctx, "set_lo_freq: scaled lo_freq %llu lo_freq %llu band
%d\n",
> > + scaled_lo_freq, lo_freq, band);
> > +
> > + switch (band) {
> > + case MAX2175_BAND_AM:
> > + if (max2175_read_bit(ctx, 5, 7) == 0)
> > + lo_mult = 16;
>
> else is lo_mult = 1. No idea if it is correct, but sounds very small
> output divider for low freq like am band. And on the other-hand local
> oscillator output divider, which I expect this to be, is usually 2 or more.
>
> > + break;
> > + case MAX2175_BAND_FM:
> > + if (lo_freq <= 74700000) {
> > + lo_mult = 16;
>
> No meaning as you set it later 8.
>
> > + } else if (lo_freq > 74700000 && lo_freq <= 110000000) {
> > + loband_bits = 1;
> > + } else {
> > + loband_bits = 1;
> > + vcodiv_bits = 3;
> > + }
> > + lo_mult = 8;
> > + break;
> > + case MAX2175_BAND_VHF:
> > + if (lo_freq <= 210000000) {
> > + loband_bits = 2;
> > + vcodiv_bits = 2;
> > + } else {
> > + loband_bits = 2;
> > + vcodiv_bits = 1;
> > + }
> > + lo_mult = 4;
> > + break;
> > + default:
> > + loband_bits = 3;
> > + vcodiv_bits = 2;
> > + lo_mult = 2;
> > + break;
> > + }
> > +
> > + if (band == MAX2175_BAND_L)
> > + scaled_npf = div_u64(div_u64(scaled_lo_freq, ctx->xtal_freq),
> > + lo_mult);
> > + else
> > + scaled_npf = div_u64(scaled_lo_freq, ctx->xtal_freq) *
lo_mult;
> > +
> > + scaled_npf = div_u64(scaled_npf, 100);
> > + scaled_integer = div_u64(scaled_npf, scale_factor) * scale_factor;
> > + int_desired = div_u64(scaled_npf, scale_factor);
> > + scaled_fraction = scaled_npf - scaled_integer;
> > + frac_desired = div_u64(scaled_fraction << 20, scale_factor);
> > +
> > + /* Check CSM is not busy */
> > + ret = max2175_poll_csm_ready(ctx);
> > + if (ret)
> > + return ret;
> > +
> > + mxm_dbg(ctx, "loband %u vcodiv %u lo_mult %u scaled_npf %llu\n",
> > + loband_bits, vcodiv_bits, lo_mult, scaled_npf);
> > + mxm_dbg(ctx, "scaled int %llu frac %llu desired int %u frac %u\n",
> > + scaled_integer, scaled_fraction, int_desired, frac_desired);
> > +
> > + /* Write the calculated values to the appropriate registers */
> > + max2175_write(ctx, 1, int_desired);
> > + max2175_write_bits(ctx, 2, 3, 0, (frac_desired >> 16) & 0xf);
> > + max2175_write(ctx, 3, frac_desired >> 8);
> > + max2175_write(ctx, 4, frac_desired);
> > + max2175_write_bits(ctx, 5, 3, 2, loband_bits);
> > + max2175_write_bits(ctx, 6, 7, 6, vcodiv_bits);
> > + return ret;
> > +}
>
> That synthesizer config is hard to understand. It seems to be
> fractional-N, with configurable N, K and output divider - like a school
> book example.
>
> +----------------------------+
> v |
> Fref +----+ +-------+ +------+
> ------> | PD | --> | VCO | ------> | /N.F |
> +----+ +-------+ +------+
> |
> |
> v
> +-------+ Fout
> | /Rout | ------>
> +-------+
>
> I made following look-up table in order to understand it:
>
> band lo freq band vcodiv div_out
> AM < 50000000 0 0 16 // reg 5 bit 7 ?
> FM < 74700000 0 0 16
> FM < 110000000 1 0 8
> FM < 160000000 1 3 8
> VHF < 210000000 2 2 4
> VHF < 600000000 2 1 4
> L <2000000000 3 2 2
>
> "vcodiv" looks unrelated to synth calculation, dunno what it is.
>
> One which makes calculation very complex looking is that it is based of
> floating point calculus. On integer mathematics you should replace
> fractional part with fractional modulus (usually letter "K" is used for
> fractional modulus on PLL calc).
>
> So that ends up something like:
> 1) select suitable lo output divider from desired output frequency
> 2) calculate vco frequency
> 3) convert vco frequency to N and K
> * N = Fvco/Fref
> * K = Fvco%Fref
> 4) convert K to control word (looks like << 20)
> 5) program values
>
> Result should be calculus without scaling.
Thanks for reviewing this part.
I'd like to add that we already have two PLL helpers in the media subsystem,
in drivers/media/i2c/aptina-pll.c and drivers/media/i2c/smiapp-pll.c. As the
PLL used here seems to be a classic one, it would make sense to also extract
the code in a helper function that could be shared between drivers.
--
Regards,
Laurent Pinchart
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
