Em Thu, 28 Jun 2018 18:20:45 +0200
Marco Felsch <m.fel...@pengutronix.de> escreveu:
> From: Philipp Zabel <p.za...@pengutronix.de>
>
> To avoid short frames on stream start, keep output pins at high impedance
> while we are not properly locked onto the input signal.
>
> Signed-off-by: Philipp Zabel <p.za...@pengutronix.de>
> Signed-off-by: Marco Felsch <m.fel...@pengutronix.de>
> ---
> drivers/media/i2c/tvp5150.c | 39 ++++++++++++++++++++++++++-----------
> 1 file changed, 28 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/media/i2c/tvp5150.c b/drivers/media/i2c/tvp5150.c
> index d8bdbedd8826..27cfd08be3d2 100644
> --- a/drivers/media/i2c/tvp5150.c
> +++ b/drivers/media/i2c/tvp5150.c
> @@ -60,6 +60,7 @@ struct tvp5150 {
> v4l2_std_id detected_norm;
> u32 input;
> u32 output;
> + u32 oe;
> int enable;
> bool lock;
>
> @@ -799,14 +800,20 @@ static irqreturn_t tvp5150_isr(int irq, void *dev_id)
> {
> struct tvp5150 *decoder = dev_id;
> struct regmap *map = decoder->regmap;
> - unsigned int active = 0, status = 0;
> + unsigned int mask, active = 0, status = 0;
> +
> + mask = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_SYNC_OE |
> + TVP5150_MISC_CTL_CLOCK_OE;
>
> regmap_read(map, TVP5150_INT_STATUS_REG_A, &status);
> if (status) {
> regmap_write(map, TVP5150_INT_STATUS_REG_A, status);
>
> - if (status & TVP5150_INT_A_LOCK)
> + if (status & TVP5150_INT_A_LOCK) {
> decoder->lock = !!(status & TVP5150_INT_A_LOCK_STATUS);
> + regmap_update_bits(map, TVP5150_MISC_CTL, mask,
> + decoder->lock ? decoder->oe : 0);
> + }
>
> return IRQ_HANDLED;
> }
> @@ -872,10 +879,26 @@ static int tvp5150_enable(struct v4l2_subdev *sd)
> /* Disable autoswitch mode */
> tvp5150_set_std(sd, std);
>
> - if (decoder->mbus_type == V4L2_MBUS_PARALLEL)
> + /*
> + * Enable the YCbCr and clock outputs. In discrete sync mode
> + * (non-BT.656) additionally enable the the sync outputs.
> + */
> + switch (decoder->mbus_type) {
> + case V4L2_MBUS_PARALLEL:
> /* 8-bit 4:2:2 YUV with discrete sync output */
> regmap_update_bits(decoder->regmap, TVP5150_DATA_RATE_SEL,
> 0x7, 0x0);
> + decoder->oe = TVP5150_MISC_CTL_YCBCR_OE |
> + TVP5150_MISC_CTL_CLOCK_OE |
> + TVP5150_MISC_CTL_SYNC_OE;
> + break;
> + case V4L2_MBUS_BT656:
> + decoder->oe = TVP5150_MISC_CTL_YCBCR_OE |
> + TVP5150_MISC_CTL_CLOCK_OE;
> + break;
> + default:
> + return -EINVAL;
> + }
>
> return 0;
> };
> @@ -1190,14 +1213,8 @@ static int tvp5150_s_stream(struct v4l2_subdev *sd,
> int enable)
> if (enable) {
> tvp5150_enable(sd);
>
> - /*
> - * Enable the YCbCr and clock outputs. In discrete sync mode
> - * (non-BT.656) additionally enable the the sync outputs.
> - */
> - val = TVP5150_MISC_CTL_YCBCR_OE | TVP5150_MISC_CTL_CLOCK_OE;
> - if (decoder->mbus_type == V4L2_MBUS_PARALLEL)
> - val |= TVP5150_MISC_CTL_SYNC_OE;
> -
> + /* Enable outputs if decoder is locked */
> + val = decoder->lock ? decoder->oe : 0;
Hmm... this only works if the tvp5150 has the interrupts enabled.
The code should be, instead:
if (c->irq)
val = decoder->lock ? decoder->oe : 0;
else
val = decoder->oe;
> int_val = TVP5150_INT_A_LOCK;
> }
>
Thanks,
Mauro
