hermann pitton a écrit :
Hi Tom,

Am Mittwoch, den 23.12.2009, 13:17 +0100 schrieb tomloh...@gmail.com:
Some news,
Hi hermann,

we are this results :


&tda827x_cfg_0, &tda827x_cfg_1 or &tda827x_cfg_2

we have a perfect image without sound on the analogic part (test with mplayer), a partial result with dvb-t : we need to initialize first with analogic (with cold boot, the card doesn't work on dvb) but only for few seconds(sound and image are ok) then re-initialize with analogic, work for few seconds on dvb and then nothing maybe i am wrong but, the sound part for analogic is a problem of redirection, isn't it ?
here are our configuration for this card :

in saa7134-dvb.c

static struct tda1004x_config tda827x_flydvbtduo_medion_config = {
    .demod_address = 0x08,
    .invert        = 1,
    .invert_oclk   = 0,
    .xtal_freq     = TDA10046_XTAL_16M,
    .agc_config    = TDA10046_AGC_TDA827X,
    .gpio_config   = TDA10046_GP01_I,
    .if_freq       = TDA10046_FREQ_045,
    .i2c_gate      = 0x4b,
    .tuner_address = 0x61,
    .antenna_switch = 2,
    .request_firmware = philips_tda1004x_request_firmware

        if (configure_tda827x_fe(dev, &tda827x_flydvbtduo_medion_config,
                     &tda827x_cfg_2) < 0)
            goto dettach_frontend;
        wprintk("Huh? unknown DVB card?\n");

in saa7134-cards.c

       .name           = "LifeView FlyDVB-T DUO Medion",
.audio_clock = 0x00187de7,
change with  0x00200000 and there is a perfect sound :)

fine. In README.saa7134 since Gerd wrote it the first time ;)

       .tuner_type     = TUNER_PHILIPS_TDA8290,
       .radio_type     = UNSET,
       .tuner_addr    = ADDR_UNSET,
       .radio_addr    = ADDR_UNSET,
       .gpiomask    = 0x00200000,
       .mpeg           = SAA7134_MPEG_DVB,
       .inputs         = {{
           .name = name_tv,
           .vmux = 1,
           .amux = TV,
           .gpio = 0x200000,     /* GPIO21=High for TV input */
           .tv   = 1,
           .name = name_comp1,    /* Composite signal on S-Video input */
           .vmux = 3,
           .amux = LINE1,
           .name = name_svideo,    /* S-Video signal on S-Video input */
           .vmux = 8,
           .amux = LINE1,
       .radio = {
           .name = name_radio,
           .amux = TV,
           .gpio = 0x000000,    /* GPIO21=Low for FM radio antenna */

.vendor       = PCI_VENDOR_ID_PHILIPS,
       .device       = PCI_DEVICE_ID_PHILIPS_SAA7133,
.subvendor = 0x5168, .subdevice = 0x0307, /* LR307-N */ .driver_data = SAA7134_BOARD_FLYDVBTDUO_MEDION,

       /* this is a hybrid board, initialize to analog mode
        * and configure firmware eeprom address
       u8 data[] = { 0x3c, 0x33, 0x60};
struct i2c_msg msg = {.addr=0x08, .flags=0, .buf=data, .len = sizeof(data)};
       i2c_transfer(&dev->i2c_adap, &msg, 1);

What can we do to have dvb fully supported ?
Can someone point me in the right direction ?

hi hermann
Hmmm, is there not anything with i2c_debug=1 before it fails after a few
will post this
Gpio pins can trigger cascades of switches, so to know the gpio status
of the card for working DVB-T on m$ might still be a desire. Maybe chips
power off.
will post the results of dscaler
Also, for 99.99% only a shot at the dark side of the moon before ever
seen, but I would also try to force TS_SERIAL to have it visited.


Thanks for you answer

To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to