The TVP5150/1 decoders support different video input sources to their AIP1A/B pins.
Possible configurations are as follows: - Analog Composite signal connected to AIP1A. - Analog Composite signal connected to AIP1B. - Analog S-Video Y (luminance) and C (chrominance) signals connected to AIP1A and AIP1B respectively. This patch extends the device tree bindings documentation to describe how the input connectors for these devices should be defined in a DT. Signed-off-by: Marco Felsch <m.fel...@pengutronix.de> Reviewed-by: Rob Herring <r...@kernel.org> --- Changelog: v7: Hi Rob, I droped your r b tag because I changed the bindings in this patch version. Please can you have a look on it again? - fix missing AIP1B svideo connection (description and examples) v3: - remove examples for one and two inputs - replace space by tabs v2: - adapt port layout in accordance with https://www.spinics.net/lists/linux-media/msg138546.html with the svideo-connector deviation (use only one endpoint) .../devicetree/bindings/media/i2c/tvp5150.txt | 112 ++++++++++++++++-- 1 file changed, 105 insertions(+), 7 deletions(-) diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt index 8c0fc1a26bf0..28b64ad149ef 100644 --- a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -12,11 +12,32 @@ Optional Properties: - pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. - reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. -The device node must contain one 'port' child node for its digital output -video port, in accordance with the video interface bindings defined in -Documentation/devicetree/bindings/media/video-interfaces.txt. +The device node must contain one 'port' child node per device physical input +and output port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes +are numbered as follows -Required Endpoint Properties for parallel synchronization: + Name Type Port + -------------------------------------- + AIP1A sink 0 + AIP1B sink 1 + Y-OUT src 2 + +The device node must contain at least one sink port and the src port. Each input +port must be linked to an endpoint defined in +Documentation/devicetree/bindings/display/connector/analog-tv-connector.txt. The +port/connector layout is as follows + +tvp-5150 port@0 (AIP1A) + endpoint@0 -----------> Comp0-Con port + endpoint@1 ------+----> Svideo-Con port +tvp-5150 port@1 (AIP1B) | + endpoint@1 ------+ + endpoint@0 -----------> Comp1-Con port +tvp-5150 port@2 + endpoint (video bitstream output at YOUT[0-7] parallel bus) + +Required Endpoint Properties for parallel synchronization on output port: - hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). - vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). @@ -26,17 +47,94 @@ Required Endpoint Properties for parallel synchronization: If none of hsync-active, vsync-active and field-even-active is specified, the endpoint is assumed to use embedded BT.656 synchronization. -Example: +Example - three input sources: + +comp_connector_0 { + compatible = "composite-video-connector"; + label = "Composite0"; + + port { + composite0_to_tvp5150: endpoint { + remote-endpoint = <&tvp5150_to_composite0>; + }; + }; +}; + +comp_connector_1 { + compatible = "composite-video-connector"; + label = "Composite1"; + + port { + composite1_to_tvp5150: endpoint { + remote-endpoint = <&tvp5150_to_composite1>; + }; + }; +}; + +svideo_connector { + compatible = "svideo-connector"; + label = "S-Video"; + + port { + #address-cells = <1>; + #size-cells = <0>; + + svideo_luma_to_tvp5150: endpoint@0 { + reg = <0>; + remote-endpoint = <&tvp5150_to_svideo_luma>; + }; + + svideo_chroma_to_tvp5150: endpoint@1 { + reg = <1>; + remote-endpoint = <&tvp5150_to_svideo_chroma>; + }; + }; +}; &i2c2 { - ... tvp5150@5c { compatible = "ti,tvp5150"; reg = <0x5c>; pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tvp5150_to_composite0: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite0_to_tvp5150>; + }; + + tvp5150_to_svideo_luma: endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_luma_to_tvp5150>; + }; + }; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + tvp5150_to_composite1: endpoint@0 { + reg = <0>; + remote-endpoint = <&composite1_to_tvp5150>; + }; + + tvp5150_to_svideo_chroma: endpoint@1 { + reg = <1>; + remote-endpoint = <&svideo_chroma_to_tvp5150>; + }; + }; + + port@2 { + reg = <2>; - port { tvp5150_1: endpoint { remote-endpoint = <&ccdc_ep>; }; -- 2.20.1