Hi Laurent,
On 01/19/2011 05:38 PM, Laurent Pinchart wrote:
> Hi Michael,
>
<snip>
>>>> @@ -1144,10 +1148,15 @@ static void ccdc_configure(struct
>>>> isp_ccdc_device *ccdc) else
>>>>
>>>> syn_mode &= ~ISPCCDC_SYN_MODE_SDR2RSZ;
>>>>
>>>> - isp_reg_writel(isp, syn_mode, OMAP3_ISP_IOMEM_CCDC, ISPCCDC_SYN_MODE);
>>>> + /* Use PACK8 mode for 1byte per pixel formats */
>>>>
>>>> - /* CCDC_PAD_SINK */
>>>> - format = &ccdc->formats[CCDC_PAD_SINK];
>>>> + if (isp_video_format_info(format->code)->bpp <= 8)
>>>> + syn_mode |= ISPCCDC_SYN_MODE_PACK8;
>>>> + else
>>>> + syn_mode &= ~ISPCCDC_SYN_MODE_PACK8;
>>>> +
>>
>> It would make sense to me to move this bit into ispccdc_config_sync_if().
>
> Why do you think so ? This configures how the data is written to memory,
> while
> ispccdc_config_sync_if() configures the CCDC input interface.
I see. I was only thinking of ispccdc_config_sync_if() as configuring
the CCDC_SYN_MODE register. I was in fact wondering why the other
syn_mode assignments weren't made in there. Now that I understand the
division, I agree that setting PACK8 makes sense wherever the other
memory-writing settings are.
>
>>>> +
>>>> + isp_reg_writel(isp, syn_mode, OMAP3_ISP_IOMEM_CCDC, ISPCCDC_SYN_MODE);
>>>>
>>>> /* Mosaic filter */
>>>> switch (format->code) {
>>>>
>>>> @@ -2244,7 +2253,12 @@ int isp_ccdc_init(struct isp_device *isp)
>>>>
>>>> ccdc->syncif.vdpol = 0;
>>>>
>>>> ccdc->clamp.oblen = 0;
>>>>
>>>> - ccdc->clamp.dcsubval = 64;
>>>> +
>>>> + if (isp->pdata->subdevs->interface == ISP_INTERFACE_PARALLEL
>>>> + && isp->pdata->subdevs->bus.parallel.width <= 8)
>>>> + ccdc->clamp.dcsubval = 0;
>>>> + else
>>>> + ccdc->clamp.dcsubval = 64;
>>>
>>> I don't like this too much. What happens if you have several sensors
>>> connected to the system with different bus width ?
>>
>> I see Laurent's point here. Maybe move the dcsubval assignment into
>> ccdc_configure(). Also, don't we also want to remove dcsubval for an
>> 8-bit serially-attached sensor? In ccdc_configure() you could make it
>> conditional on the mbus format's width on the CCDC sink pad.
>
> This piece of code only sets the default value. If the user sets another
> value, the driver must not override it silently when the video stream is
> started. I'm not really sure how to properly fix this. The best solution is
> of
> course to set the value from userspace.
I see the predicament. 64 is a bad default value for 8-bit data, but we
can't at init time know whether we're going to have 8-bit data or
10(+)-bit data to set a different default. And you can't make a 64-or-0
decision at runtime because the user may have set a custom value after
init (although this isn't currently possible). But I don't think a user
should have to adjust dcsubval just because he changed to an 8-bit image
and wants a decent image. Especially since at the moment the user can't
do that anyway. What I keep coming back to, though it sounds ugly, is 2
different default values for dcsubval.
>
>>>> ccdc->vpcfg.pixelclk = 0;
>
MATRIX VISION GmbH, Talstrasse 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschaeftsfuehrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
