On 01/26/2012 01:46 PM, Claus Olesen wrote:
the dmesg output from inplug of 290e until usb mem stick mount timeout
with a cut marked "--- cut similar ---" between mount and timeout for
less output is
I think it is maybe some incapability of em28xx driver. Maybe it could
be something to do with USB HCI too...
Could you test latest drivers using media_build.git ?
inplug 290e
[ 112.367345] usb 2-3: new high-speed USB device number 2 using ehci_hcd
[ 112.482773] usb 2-3: New USB device found, idVendor=2013, idProduct=024f
[ 112.482783] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 112.482790] usb 2-3: Product: PCTV 290e
[ 112.482796] usb 2-3: Manufacturer: PCTV Systems
[ 112.482801] usb 2-3: SerialNumber: 00000006VEJQ
[ 112.988850] em28xx: New device PCTV Systems PCTV 290e @ 480 Mbps
(2013:024f, interface 0, class 0)
[ 112.988929] em28xx #0: chip ID is em28174
[ 113.284694] em28xx #0: Identified as PCTV nanoStick T2 290e (card=78)
[ 113.340323] Registered IR keymap rc-pinnacle-pctv-hd
[ 113.340594] input: em28xx IR (em28xx #0) as
/devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1/input19
[ 113.341677] rc1: em28xx IR (em28xx #0) as
/devices/pci0000:00/0000:00:1d.7/usb2/2-3/rc/rc1
[ 113.342411] em28xx #0: v4l2 driver version 0.1.3
[ 113.348855] em28xx #0: V4L2 video device registered as video1
[ 113.350562] usbcore: registered new interface driver em28xx
[ 113.350568] em28xx driver loaded
[ 113.480057] tda18271 17-0060: creating new instance
[ 113.485221] TDA18271HD/C2 detected @ 17-0060
[ 113.724218] tda18271 17-0060: attaching existing instance
[ 113.724227] DVB: registering new adapter (em28xx #0)
[ 113.724235] DVB: registering adapter 0 frontend 0 (Sony CXD2820R
(DVB-T/T2))...
[ 113.724763] DVB: registering adapter 0 frontend 1 (Sony CXD2820R (DVB-C))...
[ 113.728614] em28xx #0: Successfully loaded em28xx-dvb
[ 113.728617] Em28xx: Initialized (Em28xx dvb Extension) extension
inplug usb mem stick
[ 136.177341] usb 2-1: new high-speed USB device number 3 using ehci_hcd
[ 136.308531] usb 2-1: New USB device found, idVendor=0bda, idProduct=0120
[ 136.308541] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 136.308548] usb 2-1: Product: USB2.0-CRW
[ 136.308554] usb 2-1: Manufacturer: Generic
[ 136.308559] usb 2-1: SerialNumber: 20060413092100000
[ 136.630379] Initializing USB Mass Storage driver...
[ 136.630764] scsi6 : usb-storage 2-1:1.0
[ 136.631270] usbcore: registered new interface driver usb-storage
[ 136.631275] USB Mass Storage support registered.
[ 137.636863] scsi 6:0:0:0: Direct-Access Generic- Card Reader
1.00 PQ: 0 ANSI: 0 CCS
[ 137.639519] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 138.446467] sd 6:0:0:0: [sdc] 15661056 512-byte logical blocks:
(8.01 GB/7.46 GiB)
[ 138.447282] sd 6:0:0:0: [sdc] Write Protect is off
[ 138.447291] sd 6:0:0:0: [sdc] Mode Sense: 03 00 00 00
[ 138.448138] sd 6:0:0:0: [sdc] No Caching mode page present
[ 138.448147] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 138.451639] sd 6:0:0:0: [sdc] No Caching mode page present
[ 138.451647] sd 6:0:0:0: [sdc] Assuming drive cache: write through
[ 138.452729] sdc: sdc1
mount usb mem stick sdc1
[ 168.838133] usb 2-1: reset high-speed USB device number 3 using ehci_hcd
[... removed lot of similar USB errors ...]
driverbyte=DRIVER_SENSE
[ 478.342504] sd 6:0:0:0: [sdc] Sense Key : Illegal Request [current]
[ 478.342510] sd 6:0:0:0: [sdc] Add. Sense: Logical block address out of range
[ 478.342517] sd 6:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 20 00 00 00 01 00
[ 478.342528] end_request: I/O error, dev sdc, sector 8192
[ 478.342545] FAT-fs (sdc1): unable to read boot sector
On Thu, Jan 26, 2012 at 10:07 AM, Antti Palosaari<cr...@iki.fi> wrote:
On 01/26/2012 12:16 AM, Claus Olesen wrote:
just got 3.2.1-3.fc16.i686.PAE
the issue that the driver had to be removed for the 290e to work after
a replug is gone.
the issue that a usb mem stick cannot be mounted while the 290e is
plugged in still lingers.
one workaround is to unplug the 290e and wait a little (no need to
also remove the driver).
What it prints to the system log? Use tail -f /var/log/messages or dmesg.
Antti
--
http://palosaari.fi/
--
http://palosaari.fi/
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
