Hi Laurent, 2012/9/28 Laurent Pinchart <laurent.pinch...@ideasonboard.com>: > Hi Enric, > > On Thursday 27 September 2012 18:05:56 Enric Balletbò i Serra wrote: >> 2012/9/27 Laurent Pinchart <laurent.pinch...@ideasonboard.com>: >> > On Wednesday 26 September 2012 16:15:35 Enric Balletbò i Serra wrote: >> >> 2012/9/26 Laurent Pinchart <laurent.pinch...@ideasonboard.com>: >> >> > On Wednesday 26 September 2012 09:57:53 Enric Balletbò i Serra wrote: >> >> > >> >> > [snip] >> >> > >> >> >> You had reason. Checking the data lines of the camera bus with an >> >> >> oscilloscope I see I had a problem, exactly in D8 /D9 data lines. >> >> > >> >> > I'm curious, how have you fixed that ? >> >> >> >> The board had a pull-down 4k7 resistor which I removed in these lines >> >> (D8/D9). The board is prepared to accept sensors from 8 to 12 bits, >> >> lines from D8 to D12 have a pull-down resistor to tie down the line by >> >> default. >> >> >> >> With the oscilloscope I saw that D8/D9 had problems to go to high >> >> level like you said, then I checked the schematic and I saw these >> >> resistors. >> >> >> >> >> Now I can capture images but the color is still wrong, see the >> >> >> following >> >> >> image captured with pipeline SENSOR -> CCDC OUTPUT >> >> >> >> >> >> http://downloads.isee.biz/pub/files/patterns/img-000001.pnm >> >> >> >> >> >> Now the image was converted using : >> >> >> ./raw2rgbpnm -s 752x480 -f SGRBG10 img-000001.bin img-000001.pnm >> >> >> >> >> >> And the raw data can be found here: >> >> >> http://downloads.isee.biz/pub/files/patterns/img-000001.bin >> >> >> >> >> >> Any idea where I can look ? Thanks. >> >> > >> >> > Your sensors produces BGGR data if I'm not mistaken, not GRBG. >> >> > raw2rgbpnm doesn't support BGGR (yet), but the OMAP3 ISP preview engine >> >> > can convert that to YUV since v3.5. Just make your sensor driver expose >> >> > the right media bus format and configure the pipeline accordingly. >> >> >> >> The datasheet (p.10,11) says that the Pixel Color Pattern is as follows. >> >> >> >> <------------------------ direction >> >> n 4 3 2 1 >> >> .. GB GB GB GB >> >> .. RG RG RG RG >> >> >> >> So seems you're right, if the first byte is on the right the sensor >> >> produces BGGR. But for some reason the mt9v032 driver uses GRBG data. >> > >> > You can change the Bayer pattern by moving the crop rectangle. That how >> > the mt9v032 driver ensures a GRBG pattern even though the first active >> > pixel in the sensor array is a blue one. As the MT9V034 first active pixel >> > is located at different coordinates you will have to modify the crop >> > rectangle computation logic to get GRBG. >> >> Please, could you explain how to do this ? I'm a newbie into image >> sensors world :-) > > Let's assume the following Bayer pattern (left to right and top to bottom > direction). > > | 1 2 3 4 5 6 7 8 ... > ---------------------- > 1| G R G R G R G R ... > 2| B G B G B G B G ... > 3| G R G R G R G R ... > 4| B G B G B G B G ... > 5| G R G R G R G R ... > 6| B G B G B G B G ... > 7| G R G R G R G R ... > 8| B G B G B G B G ... > .| ................... > > If you crop the (1,1)/4x4 rectangle from that sensor you will get > > | 1 2 3 4 > ---------- > 1| G R G R > 2| B G B G > 3| G R G R > 4| B G B G > > which is clearly a GRBG pattern. If you crop the (2,1)/4x4 rectangle you will > get > > | 2 3 4 5 > ---------- > 1| R G R G > 2| G B G B > 3| R G R G > 4| G B G B > > which is now a RGGB pattern. The pattern you get out of your sensor thus > depends on the crop rectangle position. >
Many thanks for the explanation. I'm learning a lot with your explanations :-) >> >> Maybe is related with following lines which writes register 0x0D Read >> >> Mode (p.26,27) and presumably flips row or column bytes (not sure >> >> about this I need to check) >> >> >> >> 334 /* Configure the window size and row/column bin */ >> >> 335 hratio = DIV_ROUND_CLOSEST(crop->width, format->width); >> >> 336 vratio = DIV_ROUND_CLOSEST(crop->height, format->height); >> >> 337 >> >> 338 ret = mt9v032_write(client, MT9V032_READ_MODE, >> >> 339 (hratio - 1) << >> >> MT9V032_READ_MODE_ROW_BIN_SHIFT | >> >> 340 (vratio - 1) << >> >> MT9V032_READ_MODE_COLUMN_BIN_SHIFT); >> >> >> >> Nonetheless, I changed the driver to configure for BGGR pattern. Using >> >> the Sensor->CCDC->Preview->Resizer pipeline I captured the data with >> >> yavta and converted using raw2rgbpnm program. >> >> >> >> ./raw2rgbpnm -s 752x480 -f UYVY img-000001.uyvy img-000001.pnm >> >> >> >> and the result is >> >> >> >> http://downloads.isee.biz/pub/files/patterns/img-000002.pnm >> >> http://downloads.isee.biz/pub/files/patterns/img-000002.bin >> >> >> >> The image looks better than older, not perfect, but better. The image >> >> is only a bit yellowish. Could be this a hardware issue ? We are close >> >> to ... >> > >> > It's like a white balance issue. The OMAP3 ISP hardware doesn't perform >> > automatic white balance, you will need to implement an AWB algorithm in >> > software. You can have a look at the omap3-isp-live project for sample >> > code (http://git.ideasonboard.org/omap3-isp-live.git). > So you think the sensor is set well now ? The hardware can produce this issue ? Do you know if this algorithm is implemented in gstreamer ? Regards, Enric -- To unsubscribe from this list: send the line "unsubscribe linux-media" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
