On Tue, May 26, 2015 at 11:37:17AM -0700, Arun Ramamurthy wrote: > Hi > > On 15-05-26 07:19 AM, Felipe Balbi wrote: > >HI, > > > >On Mon, May 25, 2015 at 02:19:58PM -0700, Arun Ramamurthy wrote: > >> > >> > >>On 15-05-14 05:52 PM, Felipe Balbi wrote: > >>>Hi, > >>> > >>>On Wed, Apr 22, 2015 at 04:04:10PM -0700, Arun Ramamurthy wrote: > >>>>Most of the phy providers use "select" to enable GENERIC_PHY. Since select > >>>>is only recommended when the config is not visible, GENERIC_PHY is changed > >>>>an invisible option. To maintain consistency, all phy providers are > >>>>changed > >>>>to "select" GENERIC_PHY and all non-phy drivers use "depends on" when the > >>>>phy framework is explicity required. USB_MUSB_OMAP2PLUS has a cyclic > >>>>dependency, so it is left as "select". > >>>> > >>>>Signed-off-by: Arun Ramamurthy <arun.ramamur...@broadcom.com> > >>>>--- > >>>> drivers/ata/Kconfig | 1 - > >>>> drivers/media/platform/exynos4-is/Kconfig | 2 +- > >>>> drivers/phy/Kconfig | 4 ++-- > >>>> drivers/usb/host/Kconfig | 4 ++-- > >>>> drivers/video/fbdev/exynos/Kconfig | 2 +- > >>>> 5 files changed, 6 insertions(+), 7 deletions(-) > >>>> > >>>>diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig > >>>>index 5f60155..6d2e881 100644 > >>>>--- a/drivers/ata/Kconfig > >>>>+++ b/drivers/ata/Kconfig > >>>>@@ -301,7 +301,6 @@ config SATA_MV > >>>> tristate "Marvell SATA support" > >>>> depends on PCI || ARCH_DOVE || ARCH_MV78XX0 || \ > >>>> ARCH_MVEBU || ARCH_ORION5X || COMPILE_TEST > >>>>- select GENERIC_PHY > >>>> help > >>>> This option enables support for the Marvell Serial ATA family. > >>>> Currently supports 88SX[56]0[48][01] PCI(-X) chips, > >>>>diff --git a/drivers/media/platform/exynos4-is/Kconfig > >>>>b/drivers/media/platform/exynos4-is/Kconfig > >>>>index b7b2e47..b6f3eaa 100644 > >>>>--- a/drivers/media/platform/exynos4-is/Kconfig > >>>>+++ b/drivers/media/platform/exynos4-is/Kconfig > >>>>@@ -31,7 +31,7 @@ config VIDEO_S5P_FIMC > >>>> config VIDEO_S5P_MIPI_CSIS > >>>> tristate "S5P/EXYNOS MIPI-CSI2 receiver (MIPI-CSIS) driver" > >>>> depends on REGULATOR > >>>>- select GENERIC_PHY > >>>>+ depends on GENERIC_PHY > >>>> help > >>>> This is a V4L2 driver for Samsung S5P and EXYNOS4 SoC > >>>> MIPI-CSI2 > >>>> receiver (MIPI-CSIS) devices. > >>>>diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > >>>>index 2962de2..edecdb1 100644 > >>>>--- a/drivers/phy/Kconfig > >>>>+++ b/drivers/phy/Kconfig > >>>>@@ -5,7 +5,7 @@ > >>>> menu "PHY Subsystem" > >>>> > >>>> config GENERIC_PHY > >>>>- bool "PHY Core" > >>>>+ bool > >>>> help > >>>> Generic PHY support. > >>>> > >>>>@@ -72,7 +72,7 @@ config PHY_MIPHY365X > >>>> config PHY_RCAR_GEN2 > >>>> tristate "Renesas R-Car generation 2 USB PHY driver" > >>>> depends on ARCH_SHMOBILE > >>>>- depends on GENERIC_PHY > >>>>+ select GENERIC_PHY > >>> > >>>so some you changed from depends to select... > >>> > >>>> help > >>>> Support for USB PHY found on Renesas R-Car generation 2 SoCs. > >>>> > >>>>diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig > >>>>index 5ad60e4..e2197e2 100644 > >>>>--- a/drivers/usb/host/Kconfig > >>>>+++ b/drivers/usb/host/Kconfig > >>>>@@ -182,7 +182,7 @@ config USB_EHCI_HCD_SPEAR > >>>> config USB_EHCI_HCD_STI > >>>> tristate "Support for ST STiHxxx on-chip EHCI USB controller" > >>>> depends on ARCH_STI && OF > >>>>- select GENERIC_PHY > >>>>+ depends on GENERIC_PHY > >>> > >>>while others you changed from select to depends. > >>> > >>>NAK. > >>> > >>Felipe, I dont understand your concern, could you please explain it more > >>detail? The logic behind the changes is that in cases where there was an > >>explicit dependency, I changed it to "depends on" and in other cases I > >>changed it to "selects". Thanks > > > >Since GENERIC_PHY is visible from Kconfig, it would be much nicer to > >avoid select altogether. > > > Felipe, after discussion with the maintainers, I have made GENERIC_PHY an > invisible option as part of this change. Thanks
Then, if the option is invisible, how can you "depend" on it ? It can never be selected by poking around in Kconfig. IMO, it's counterintuitive that you need to enable a PHY driver before you can see your EHCI/OHCI/whatever controller listed in Kconfig. -- balbi
signature.asc
Description: Digital signature
