Linux-Networking Digest #156, Volume #10 Tue, 9 Feb 99 09:14:29 EST
Contents:
LCP: timeout sending Config-Requests ("Pat")
Re: Help with cable modem and two netcards (Gregory G. Woodbury)
Sendmail as an internet email server (Manoli Kokologiannakis)
Re: Can't ping my Gateway (but I can ping my own IP address) ("Gary Spivey")
Modem disconnects with RH5.2 (JT)
IP Masquerading ("Mark Peoples")
Blocking email domain names (Don Stafford)
This needs to be said............. ([EMAIL PROTECTED])
Firewall Problems ("Neil Shanks")
ipfwadm: setsockopt failed (Chris Funk)
Enabling NT authentication from Linux ("S")
I know it's been asked a million times... (Jay Copeland)
----------------------------------------------------------------------------
From: "Pat" <[EMAIL PROTECTED]>
Subject: LCP: timeout sending Config-Requests
Date: Tue, 9 Feb 1999 14:08:45 +0100
Hi,
I'm using isdn4linux and a passive TelesPnP Card to connect to my provider.
Everything worked fine for a while, but now I get the the following
messages:
ipppd[90]: sent [0][LCP ConfReq id=0x1 <mru1524> <magic 0x...>
ipppd[90]: LCP: timeout sending Config-Requests
Does anybody know how to solve this problem, or where I can get more
information about LCP ?
Thanks
Patrick
------------------------------
From: [EMAIL PROTECTED] (Gregory G. Woodbury)
Subject: Re: Help with cable modem and two netcards
Date: 9 Feb 1999 08:36:47 GMT
Andrew Luttio <[EMAIL PROTECTED]> shaped electrons to say:
>I just got a cable modem and it is currently routed through my Linux box
>with a 3Com 3c595 and a Netgear FA310TX to a Win95 machine through a
>100BaseT hub. The cable modem comes in on the FA310TX, and the internal
>network is on the 3c595. For some reason though, Linux will only connect to
>both networks when these cards are in the machine. If I use either one of
>them with either of two NE2000 cards (Linksys LNEPCI II and a SOHOWare
>ND4300) connected to the cable modem, Linux wont ping anything on the
>internet, but can still access the internal network. All the cards are
>detected fine and I can ping the cards themselves. Anyone know what might be
>causing this? Thanks for any help.
There is a rumour that Cable modems memorize the Ethernet (MAC) addresses
of connected NIC's. You might neet to "reset" your Cable Modem so it
will acquire the news MAC addresses when you change cards.
--
Gregory G. "Wolfe" Woodbury `-_-' Owner/Admin: wolves.durham.nc.us
ggw at wolves.durham.nc.us U Errant co-moderator of:
soc.religion.unitarian-univ
"The Line Eater is a boojum snark." Hug your wolf. (Thanks Peter.)
------------------------------
From: Manoli Kokologiannakis <[EMAIL PROTECTED]>
Subject: Sendmail as an internet email server
Date: Mon, 08 Feb 1999 19:42:08 -0800
Can somebody help me setup sendmail as an email server that can be used
on the internet using pop3 clients such as Netscape Mail and Outlook.
Thanks.
------------------------------
From: "Gary Spivey" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.hardware,comp.os.linux.questions,comp.os.linux.setup
Subject: Re: Can't ping my Gateway (but I can ping my own IP address)
Date: Tue, 09 Feb 1999 12:25:15 GMT
Fair enough, i will take whatever help I can get.
Attached is the ifconfig -a, netstat -nr, and I threw in a pnpdump for fun
...
Cheers,
Gary
Andrew Comech wrote in message <[EMAIL PROTECTED]>...
>> But I cannot ping my Gateway.
>So what's the output of ifconfig and netstat -nr ?
>
>It is naive: to glue pages of output and think they would not
>ask for more...
>
>Cheers,
>Andrew
>
=================================================
ifconfig -a
=================================================
lo Link encap:Local Loopback
inet addr:127.0.0.1 Bcast:127.255.255.255 Mask:255.0.0.0
UP BROADCAST LOOPBACK RUNNING MTU:3584 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
eth0 Link encap:Ethernet HWaddr 00:A0:C9:CC:C6:21
inet addr:24.4.56.168 Bcast:24.4.56.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
TX packets:0 errors:0 dropped:0 overruns:0
Interrupt:11 Base address:0x210
=================================================
netstat -nr
=================================================
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt
Iface
24.4.56.0 0.0.0.0 255.255.255.0 U 1500 0 0
eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 3584 0 0 lo
0.0.0.0 24.4.56.1 0.0.0.0 UG 1500 0 0
eth0
=================================================
pnpdump
=================================================
# $Id: pnpdump.c,v 1.15a 1998/05/25 17:22:16 fox Exp $
# This is free software, see the sources for details.
# This software has NO WARRANTY, use at your OWN RISK
#
# For details of this file format, see isapnp.conf(5)
#
# For latest information on isapnp and pnpdump see:
# http://www.roestock.demon.co.uk/isapnptools/
#
# Compiler flags: -DREALTIME -DNEEDSETSCHEDULER
#
# Trying port address 0203
# Trying port address 020b
# Board 1 has serial identifier 9a 00 12 8f 55 44 00 8c 0e
# (DEBUG)
(READPORT 0x020b)
(ISOLATE PRESERVE)
(IDENTIFY *)
# Card 1: (serial identifier 9a 00 12 8f 55 44 00 8c 0e)
# Vendor Id CTL0044, Serial Number 1216341, checksum 0x9A.
# Version 1.0, Vendor version 1.0
# ANSI string -->Creative SB32 PnP<--
#
# Logical device id CTL0031
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 0
# ANSI string -->Audio<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 5.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 1.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 1))
# Next DMA channel 5.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0220
# IO base alignment 1 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0330
# Maximum IO base address 0x0330
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0330))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority acceptable
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Next DMA channel 5, 6 or 7.
# 16 bit DMA only
# Logical device is not a bus master
# DMA may not execute in count by byte mode
# DMA may execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 1 (CHANNEL 5))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0388
# Maximum IO base address 0x0388
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 2 (BASE 0x0388))
# Start dependent functions: priority functional
# IRQ 5, 7 or 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x0330
# IO base alignment 48 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 5, 7, 10 or 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 5 (MODE +E)))
# First DMA channel 0, 1 or 3.
# 8 bit DMA only
# Logical device is not a bus master
# DMA may execute in count by byte mode
# DMA may not execute in count by word mode
# DMA channel speed in compatible mode
# (DMA 0 (CHANNEL 0))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0220
# Maximum IO base address 0x0280
# IO base alignment 32 bytes
# Number of IO addresses required: 16
# (IO 0 (BASE 0x0220))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL2011
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 1
# Compatible device id PNP0600
# ANSI string -->IDE<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# IRQ 10.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0168
# Maximum IO base address 0x0168
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0168))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x036e
# Maximum IO base address 0x036e
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x036e))
# Start dependent functions: priority acceptable
# IRQ 11.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 11 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x01e8
# Maximum IO base address 0x01e8
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x01e8))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x03ee
# Maximum IO base address 0x03ee
# IO base alignment 1 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x03ee))
# Start dependent functions: priority acceptable
# IRQ 10, 11 or 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 10 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x01f8
# IO base alignment 8 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0100))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0300
# Maximum IO base address 0x03fe
# IO base alignment 2 bytes
# Number of IO addresses required: 2
# (IO 1 (BASE 0x0300))
# Start dependent functions: priority functional
# IRQ 15.
# High true, edge sensitive interrupt (by default)
# (INT 0 (IRQ 15 (MODE +E)))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0170
# Maximum IO base address 0x0170
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0170))
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0376
# Maximum IO base address 0x0376
# IO base alignment 1 bytes
# Number of IO addresses required: 1
# (IO 1 (BASE 0x0376))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL0021
# Device supports vendor reserved register @ 0x38
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 2
# ANSI string -->WaveTable<--
# Multiple choice time, choose one only !
# Start dependent functions: priority preferred
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0620
# IO base alignment 1 bytes
# Number of IO addresses required: 4
# (IO 0 (BASE 0x0620))
# Start dependent functions: priority acceptable
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0620
# Maximum IO base address 0x0680
# IO base alignment 32 bytes
# Number of IO addresses required: 4
# (IO 0 (BASE 0x0620))
# End dependent functions
# (ACT Y)
))
#
# Logical device id CTL7001
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 3
# Compatible device id PNPb02f
# ANSI string -->Game<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0200
# Maximum IO base address 0x0200
# IO base alignment 1 bytes
# Number of IO addresses required: 8
# (IO 0 (BASE 0x0200))
# (ACT Y)
))
#
# Logical device id CTL0051
# Device supports vendor reserved register @ 0x3b
# Device supports vendor reserved register @ 0x3c
#
# Edit the entries below to uncomment out the configuration required.
# Note that only the first value of any range is given, this may be changed
if required
# Don't forget to uncomment the activate (ACT Y) when happy
(CONFIGURE CTL0044/1216341 (LD 4
# ANSI string -->StereoEnhance<--
# Logical device decodes 16 bit IO address lines
# Minimum IO base address 0x0100
# Maximum IO base address 0x03f8
# IO base alignment 8 bytes
# Number of IO addresses required: 1
# (IO 0 (BASE 0x0100))
# (ACT Y)
))
# End tag... Checksum 0x00 (OK)
# Returns all cards to the "Wait for Key" state
(WAITFORKEY)
------------------------------
From: JT <[EMAIL PROTECTED]>
Subject: Modem disconnects with RH5.2
Date: Tue, 09 Feb 1999 03:54:53 GMT
Hello all,
While I'm not a newbie and have been running RH since v4.2, I can't
figure out what is going on here. I usually just set up ppp with the
netcfg utility and it works fine, but for some reason, I can't get it to
work in RH5.2, using the same settings as in the other versions.
Here is what the /var/log/messages says:
Feb 8 20:04:12 viper pppd[495]: pppd 2.3.5 started by root, uid 0
Feb 8 20:04:19 viper innd[425]: s
Feb 8 20:04:29 viper pppd[495]: Serial connection established.
Feb 8 20:04:30 viper pppd[495]: Using interface ppp0
Feb 8 20:04:30 viper pppd[495]: Connect: ppp0 <--> /dev/modem
Feb 8 20:04:46 viper pppd[495]: Remote message: Login Succeeded
Feb 8 20:04:47 viper pppd[495]: not replacing existing default route to
eth0 [192.168.0.1]
Feb 8 20:04:47 viper pppd[495]: local IP address 209.30.51.108
Feb 8 20:04:47 viper pppd[495]: remote IP address 209.30.51.5
Feb 8 20:05:17 viper pppd[495]: CCP: timeout sending Config-Requests
Feb 8 20:06:02 viper innfeed[453]: decwrl can't resolve hostname:
news1.pa.dec.com : (Host name lookup failure)
Feb 8 20:06:02 viper innfeed[453]: decwrl spooling no active
connections
I got the CD from cheapbytes, as with all my other versions. Any help
would be appreciated.
TIA,
JT
------------------------------
From: "Mark Peoples" <[EMAIL PROTECTED]>
Subject: IP Masquerading
Date: Mon, 8 Feb 1999 20:56:22 -0700
Hello All,
I have IP Masquerading working (my linux box is currently connected to my
ISP and I am using Outlook Express on my Win98 machine to write this). I
can "surf" the web...whatever that means and send/receive e-mail/news.
However, I can't ftp or telnet to my linux box.
Any ideas?
Thanks,
Mark Peoples
------------------------------
From: [EMAIL PROTECTED] (Don Stafford)
Subject: Blocking email domain names
Date: Tue, 09 Feb 1999 13:15:06 GMT
Reply-To: [EMAIL PROTECTED]
Is there a way using the POP3 and SENDMAIL servers that come with
Redhat 5.2, to deny email messages being sent to and received from
specific domains?
Don Stafford, Director of Information Technologies
UAV Entertainment
2200 Carolina Place
Fort Mill, SC 29715
Phone: 803.548.1056 x159
Fax: 803.548.2493
[EMAIL PROTECTED]
http://www.uavco.com/
------------------------------
From: [EMAIL PROTECTED]
Subject: This needs to be said.............
Date: Tue, 09 Feb 1999 03:54:44 GMT
Lately I learned of the Service Pack 3 failure to fix the Y2K problem
in Windows NT 4.0. This extremely angers me that a company charging so much
money for a product can market such a poor product. Nowhere else would this
be tolerated. But we tolerate it because it is the graphical interface that
we all know and can use. Why are Microsofts two current frontline products
such a failure with Y2k? Where is the liability. It makes no sense. Hopefully
there are no American flags on their products. That would bring a tear to the
Native American in the commercial. When speaking to Novell Network
Administrators they speak of many things, but one small comment keeps popping
up, "This server has been up and running for I don't remember how long". That
is the bottom line in Information Technology. Period. The day NT can stand in
that shadow I will stop proclaiming that I like to "Tickle its toes and poke
at its belly, because it is just a child". In the race of Networking, NT
can't seem to get by the "Restarting" line. The stories of NT 2000, no lets
say it, Windows 2005, weighted with "cut and paste visual programming"
requiring 128 MB memory is pathetic. The boys over at the memory
manufacturers should applaud. They have a pal in Mr. Gates. Give
credit where credit is due, The current Win 95/98 interface is I believe the
best workstation. All users are not computer professionals. 95/98 runs
circles around NT Workstation and can be very secure with a boot-lock program
and bios password. NT 4.0 Workstation is just too slow, even at 64 mb. If NT
was a breathing entity I would ask it what sauce it likes on its memory chips
before devouring them. I still applaud NT for being part of the IT
world which I find so special. It is still part of one of the coolest things
on the face of this earth. But NT is fed by industry money, and corporate
fanfare. True professionals stand by their products laurels. Some feel like
they have to "deal" with NT while other operating systems reside in their
hearts. Let the magazine writers write their stories of NT. There is a
product that is beginning to rise based on reliability. Many programmers have
put their lives into this product so you could taste rock-solid computing. We
need to help this product along. Take out your favorite distribution for a
weekend, just like the "Big Brother" program. Linux, or what it stands for,
lives in the heart of true professionals. Linus I am publically saying
"Thank-you". Applaud Red Hat Software for adopting Gnome the true GPL window
manager. The tide was traveling otherwise. Of heart they are true. If
Windows 2005, the latest overpriced beta coming out of Washington State comes
to the show buggy, it has failed. If it comes too late it has failed. Is an
intelligent person tempted to change to a product in the year prior to 2000
that is not even 2000 compliant? I hope not. They may be forced to change
because some vendor chooses NT platform for their software base. Vendors,
consultants, and service professionals know there is money in NT. Fixing
something broken provides revenue. Business may ruin what Linux is
trying to do, as it has raped many other things. Get this, many business
people wonder why IT people don't reveal their secret for the sake of a
paycheck. Infornmation Technology is art first. They will never understand.
For them God created NT.
Live, Ride, Breath Linux, not for money, but to create the best product
possible without deadlines.........
This needed to be said........................
============= Posted via Deja News, The Discussion Network ============
http://www.dejanews.com/ Search, Read, Discuss, or Start Your Own
------------------------------
From: "Neil Shanks" <[EMAIL PROTECTED]>
Subject: Firewall Problems
Date: Tue, 09 Feb 1999 13:25:18 GMT
I have a firewall setup up running Slackware 3.5.0 . It is a packet
forwarding firewall. I have three windows machines on the home network. 2
running win98 1 running win95.
My problem is the people on my network want to be able to play online
games such as Diablo, Quake, Civ2, etc. Which means I need (if posssible)
one soulution that will allow all these various games to work. Any help
would be greatly appreciated.
------------------------------
Date: Mon, 08 Feb 1999 21:04:55 -0700
From: Chris Funk <[EMAIL PROTECTED]>
Subject: ipfwadm: setsockopt failed
Hi, I am trying to get ip masq. set up.
I have the pppd part working, but when i try to issue any ipfwadm
commands I get the following errors
[ns2]# ipfwadm -F -p deny
"ipfwadm: setsockopt failed: Invalid argument
[ns2]# ipfwadm -F -a m -S 192.168.0.1/32 -D 0.0.0.0/0
"ipfwadm: setsockopt failed: No such file or directory
I compiled in ip masq. etc. Did i miss something?
Also, I have the demand line in my /etc/ppp/options file.
Should a pppd :xxx.xxx.xxx.xxx command fire up the modem?
I thought that it required me to ping something on the outside world
before it would dial the modem
Thanks
Chris Funk
------------------------------
From: "S" <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.questions,comp.os.linux.admin,comp.os.linux.setup
Subject: Enabling NT authentication from Linux
Date: Mon, 8 Feb 1999 23:09:58 -0500
I've set up a lone Linux (Redhat 5.2) box that's part of an NT network.
Instead of creating local accounts for everyone who wants to use the
machine, it would be great if the Linux machine can authenticate against an
NT PDC. Anyone know how to set this up? I'm aware of Linux Pluggable
Authentication Modules that supposedly enable this feature but the
documentation is weak. Can someone point me to some through documentation
or send me step-by-step instructions?
Thanks.
------------------------------
From: Jay Copeland <[EMAIL PROTECTED]>
Subject: I know it's been asked a million times...
Date: Thu, 28 Jan 1999 23:12:25 -0500
Reply-To: [EMAIL PROTECTED]
We have two linux boxes in our house. The older one (defiant) is a 486
66 with all kinds of dead parts with hardware workarounds. It works. I
can surf or whatever I want to do when I have a phone line plugged in.
The newer one (voyager) is an AMD 233. It's great. It's fast enough for
what we want to do.
I have been trying for about a week to get IP Masquing (sp?) to work.
I've recompiled the kernel on what will be the gateway. I've followed
the mini-HOWTO to the letter. I still haven't been able to get it to
work.
The two machines work fine together. We share files, doom, whatever
else. I just can't get to the internet unless I telnet into the gateway.
That's fine if I just want to use lynx. I can't use Netscape or its
e-mail client. I can't irc (not that it's important). What else do I
need to do?
# hosts on gateway
#
127.0.0.1 localhost
aaa.bbb.ccc.32 voyager.qx.net voyager
aaa.bbb.ccc.33 defiant.qx.net defiant
I ran net config and put voyager's address as the gateway. I'm running
Slackware 3.5, linux 2.0.34.
Thanks in advance
Jay
--
__
/ / __ __ __ __ __ __ __
/ /__ / / / \/ / / /__/ / \ \/ /
/_____/ /_/ /_/\__/ |_____/ /_/ \_\
Don't fear the Penguin.
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.networking) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Networking Digest
******************************
