* Carlos Aguiar <[EMAIL PROTECTED]> [080416 08:44]:
> From: Carlos Eduardo Aguiar <[EMAIL PROTECTED]>
> 
> This patch makes the following general code cleanup and cosmetic fixes:
> 
> - Use #include <linux/io.h> instead of <asm/io.h>, according to warning
> reported by scripts/checkpatch.pl on arch/arm/mach-omap2/board-sdp-hsmmc.c
> 
> - Use if (power_on) instead of if (power_on == 1) and if (!power_on) instead
> of if (power_on == 0).
> 
> - Use if (ret) instead of if (ret != 0).
> 
> - Add an extra-line to separate labels.
> 
> Signed-off-by: Carlos Eduardo Aguiar <[EMAIL PROTECTED]>
> Acked-by: Anderson Lizardo <[EMAIL PROTECTED]>
> Acked-by: Eduardo Valentin <[EMAIL PROTECTED]>
> ---
>  arch/arm/mach-omap2/board-sdp-hsmmc.c |   41 
> ++++++++++++++++-----------------
>  1 files changed, 20 insertions(+), 21 deletions(-)
> 
> diff --git a/arch/arm/mach-omap2/board-sdp-hsmmc.c 
> b/arch/arm/mach-omap2/board-sdp-hsmmc.c
> index 3ae5b20..71b6a21 100644
> --- a/arch/arm/mach-omap2/board-sdp-hsmmc.c
> +++ b/arch/arm/mach-omap2/board-sdp-hsmmc.c
> @@ -9,6 +9,7 @@
>   * published by the Free Software Foundation.
>   */
>  #include <linux/err.h>
> +#include <linux/io.h>
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/interrupt.h>
> @@ -17,7 +18,6 @@
>  #include <asm/hardware.h>
>  #include <asm/arch/mmc.h>
>  #include <asm/arch/board.h>
> -#include <asm/io.h>
>  
>  #if defined(CONFIG_MMC_OMAP_HS) || defined(CONFIG_MMC_OMAP_HS_MODULE)
>  
> @@ -31,7 +31,7 @@
>  #define TWL_GPIO_ISR1A               0x19
>  #define LDO_CLR                      0x00
>  #define VSEL_S2_CLR          0x40
> -#define GPIO_0_BIT_POS               1 << 0
> +#define GPIO_0_BIT_POS               (1 << 0)
>  #define MMC1_CD_IRQ          0
>  #define MMC2_CD_IRQ          1
>  
> @@ -51,27 +51,27 @@ static int sdp_mmc_late_init(struct device *dev)
>        * Configure TWL4030 GPIO parameters for MMC hotplug irq
>        */
>       ret = twl4030_request_gpio(MMC1_CD_IRQ);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       ret = twl4030_set_gpio_edge_ctrl(MMC1_CD_IRQ,
>                       TWL4030_GPIO_EDGE_RISING | TWL4030_GPIO_EDGE_FALLING);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       ret = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, 0x02,
>                                               TWL_GPIO_PUPDCTR1);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       ret = twl4030_set_gpio_debounce(MMC1_CD_IRQ, TWL4030_GPIO_IS_ENABLE);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       return ret;
> +
>  err:
>       dev_err(dev, "Failed to configure TWL4030 GPIO IRQ\n");
> -
>       return ret;
>  }
>  
> @@ -80,7 +80,7 @@ static void sdp_mmc_cleanup(struct device *dev)
>       int ret = 0;
>  
>       ret = twl4030_free_gpio(MMC1_CD_IRQ);
> -     if (ret != 0)
> +     if (ret)
>               dev_err(dev, "Failed to configure TWL4030 GPIO IRQ\n");
>  }
>  
> @@ -96,24 +96,25 @@ static int mask_cd_interrupt(int mask)
>       u8 reg = 0, ret = 0;
>  
>       ret = twl4030_i2c_read_u8(TWL4030_MODULE_GPIO, &reg, TWL_GPIO_IMR1A);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       reg = (mask == 1) ? (reg | GPIO_0_BIT_POS) : (reg & ~GPIO_0_BIT_POS);
>  
>       ret = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, reg, TWL_GPIO_IMR1A);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       ret = twl4030_i2c_read_u8(TWL4030_MODULE_GPIO, &reg, TWL_GPIO_ISR1A);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
>  
>       reg = (mask == 1) ? (reg | GPIO_0_BIT_POS) : (reg & ~GPIO_0_BIT_POS);
>  
>       ret = twl4030_i2c_write_u8(TWL4030_MODULE_GPIO, reg, TWL_GPIO_ISR1A);
> -     if (ret != 0)
> +     if (ret)
>               goto err;
> +
>  err:
>       return ret;
>  }
> @@ -155,7 +156,7 @@ static int sdp_mmc_set_power(struct device *dev, int 
> slot, int power_on,
>       #define OMAP2_CONTROL_PBIAS 0x48002520
>  #endif
>  
> -     if (power_on == 1) {
> +     if (power_on) {
>               if (cpu_is_omap24xx())
>                       devconf = omap_readl(0x490022E8);
>               else
> @@ -186,12 +187,12 @@ static int sdp_mmc_set_power(struct device *dev, int 
> slot, int power_on,
>  
>               ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
>                                               P1_DEV_GRP, VMMC1_DEV_GRP);
> -             if (ret != 0)
> +             if (ret)
>                       goto err;
>  
>               ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
>                                               vdd_sel, VMMC1_DEDICATED);
> -             if (ret != 0)
> +             if (ret)
>                       goto err;
>  
>               msleep(100);
> @@ -202,7 +203,7 @@ static int sdp_mmc_set_power(struct device *dev, int 
> slot, int power_on,
>  
>               return ret;
>  
> -     } else if (power_on == 0) {
> +     } else if (!power_on) {
>               /* Power OFF */
>  
>               /* For MMC1, Toggle PBIAS before every power up sequence */

I guess the above else if be just else with this patch?


> @@ -210,24 +211,22 @@ static int sdp_mmc_set_power(struct device *dev, int 
> slot, int power_on,
>                                       OMAP2_CONTROL_PBIAS);
>               ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
>                                               LDO_CLR, VMMC1_DEV_GRP);
> -             if (ret != 0)
> +             if (ret)
>                       goto err;
>  
>               ret = twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER,
>                                               VSEL_S2_CLR, VMMC1_DEDICATED);
> -             if (ret != 0)
> +             if (ret)
>                       goto err;
>  
>               /* 100ms delay required for PBIAS configuration */
>               msleep(100);
>               omap_writel(omap_readl(OMAP2_CONTROL_PBIAS) | 0x7,
>                       OMAP2_CONTROL_PBIAS);
> -     } else {
> -             ret = -1;
> -             goto err;
>       }
>  
>       return 0;
> +
>  err:
>       return 1;
>  }
> -- 1.5.3.GIT
> 
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to