This patch moves twl4030-usb to platform_device. Later patches
will come adding proper notifications for twl usb irq events
via sysfs. The files will be placed under
/sys/devices/platform/twl4030-usb/
Also get rid of transceiver mode Kconfig selection, that will be
done by passing the desired mode via platform_data.
Signed-off-by: Felipe Balbi <[EMAIL PROTECTED]>
---
arch/arm/mach-omap2/usb-musb.c | 19 ++
drivers/i2c/chips/Kconfig | 16 --
drivers/i2c/chips/twl4030-usb.c | 550 +++++++++++----------------------------
include/linux/i2c/twl4030-usb.h | 257 ++++++++++++++++++
4 files changed, 422 insertions(+), 420 deletions(-)
create mode 100644 include/linux/i2c/twl4030-usb.h
diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c
index 3f90a93..afb377d 100644
--- a/arch/arm/mach-omap2/usb-musb.c
+++ b/arch/arm/mach-omap2/usb-musb.c
@@ -146,9 +146,28 @@ static struct platform_device musb_device = {
};
#endif
+#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE)
+static struct twl4030_usb_platform_data twl4030_usb_plat = {
+ .usb_mode = T2_USB_MODE_ULPI,
+};
+
+static struct platform_device twl4030_usb_device = {
+ .name = "twl4030-usb",
+ .id = -1,
+ .dev = {
+ .platform_data = &twl4030_usb_plat,
+ },
+};
+#endif
void __init usb_musb_init(void)
{
+#if defined(CONFIG_TWL4030_USB) || defined(CONFIG_TWL4030_USB_MODULE)
+ if (platform_device_register(&twl4030_usb_device) < 0) {
+ printk(KERN_ERR "Unable to register TWL4030 USB device\n");
+ return;
+ }
+#endif
#ifdef CONFIG_USB_MUSB_SOC
if (platform_device_register(&musb_device) < 0) {
printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n");
diff --git a/drivers/i2c/chips/Kconfig b/drivers/i2c/chips/Kconfig
index e91be60..121aec9 100644
--- a/drivers/i2c/chips/Kconfig
+++ b/drivers/i2c/chips/Kconfig
@@ -186,22 +186,6 @@ config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE
-choice
- prompt "Transceiver mode"
- depends on TWL4030_USB
- help
- TWL4030 USB transceiver can operate in various
- mutually-exclusive modes. Select one of them.
-
-config TWL4030_USB_HS_ULPI
- depends on TWL4030_USB
- bool "High-speed ULPI"
- help
- Say Y here if the TWL4030 is connected to high-speed USB
- controller through a ULPI interface.
-
-endchoice
-
config TWL4030_PWRBUTTON
tristate "TWL4030 Power button Driver"
depends on TWL4030_CORE
diff --git a/drivers/i2c/chips/twl4030-usb.c b/drivers/i2c/chips/twl4030-usb.c
index 2906b82..0d62e65 100644
--- a/drivers/i2c/chips/twl4030-usb.c
+++ b/drivers/i2c/chips/twl4030-usb.c
@@ -2,6 +2,8 @@
* twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller
*
* Copyright (C) 2004-2007 Texas Instruments
+ * Copyright (C) 2008 Nokia Corporation
+ * Contact: Felipe Balbi <[EMAIL PROTECTED]>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
@@ -22,268 +24,37 @@
* - 3-pin mode support may be added in future.
*/
-
#include <linux/module.h>
#include <linux/init.h>
#include <linux/time.h>
#include <linux/interrupt.h>
+#include <linux/platform_device.h>
#include <linux/io.h>
#include <linux/usb.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <linux/usb/otg.h>
#include <linux/i2c/twl4030.h>
+#include <linux/i2c/twl4030-usb.h>
#include <mach/usb.h>
-/* Register defines */
-
-#define VENDOR_ID_LO 0x00
-#define VENDOR_ID_HI 0x01
-#define PRODUCT_ID_LO 0x02
-#define PRODUCT_ID_HI 0x03
-
-#define FUNC_CTRL 0x04
-#define FUNC_CTRL_SET 0x05
-#define FUNC_CTRL_CLR 0x06
-#define FUNC_CTRL_SUSPENDM (1 << 6)
-#define FUNC_CTRL_RESET (1 << 5)
-#define FUNC_CTRL_OPMODE_MASK (3 << 3) /* bits 3 and 4 */
-#define FUNC_CTRL_OPMODE_NORMAL (0 << 3)
-#define FUNC_CTRL_OPMODE_NONDRIVING (1 << 3)
-#define FUNC_CTRL_OPMODE_DISABLE_BIT_NRZI (2 << 3)
-#define FUNC_CTRL_TERMSELECT (1 << 2)
-#define FUNC_CTRL_XCVRSELECT_MASK (3 << 0) /* bits 0 and 1 */
-#define FUNC_CTRL_XCVRSELECT_HS (0 << 0)
-#define FUNC_CTRL_XCVRSELECT_FS (1 << 0)
-#define FUNC_CTRL_XCVRSELECT_LS (2 << 0)
-#define FUNC_CTRL_XCVRSELECT_FS4LS (3 << 0)
-
-#define IFC_CTRL 0x07
-#define IFC_CTRL_SET 0x08
-#define IFC_CTRL_CLR 0x09
-#define IFC_CTRL_INTERFACE_PROTECT_DISABLE (1 << 7)
-#define IFC_CTRL_AUTORESUME (1 << 4)
-#define IFC_CTRL_CLOCKSUSPENDM (1 << 3)
-#define IFC_CTRL_CARKITMODE (1 << 2)
-#define IFC_CTRL_FSLSSERIALMODE_3PIN (1 << 1)
-
-#define TWL4030_OTG_CTRL 0x0A
-#define TWL4030_OTG_CTRL_SET 0x0B
-#define TWL4030_OTG_CTRL_CLR 0x0C
-#define TWL4030_OTG_CTRL_DRVVBUS (1 << 5)
-#define TWL4030_OTG_CTRL_CHRGVBUS (1 << 4)
-#define TWL4030_OTG_CTRL_DISCHRGVBUS (1 << 3)
-#define TWL4030_OTG_CTRL_DMPULLDOWN (1 << 2)
-#define TWL4030_OTG_CTRL_DPPULLDOWN (1 << 1)
-#define TWL4030_OTG_CTRL_IDPULLUP (1 << 0)
-
-#define USB_INT_EN_RISE 0x0D
-#define USB_INT_EN_RISE_SET 0x0E
-#define USB_INT_EN_RISE_CLR 0x0F
-#define USB_INT_EN_FALL 0x10
-#define USB_INT_EN_FALL_SET 0x11
-#define USB_INT_EN_FALL_CLR 0x12
-#define USB_INT_STS 0x13
-#define USB_INT_LATCH 0x14
-#define USB_INT_IDGND (1 << 4)
-#define USB_INT_SESSEND (1 << 3)
-#define USB_INT_SESSVALID (1 << 2)
-#define USB_INT_VBUSVALID (1 << 1)
-#define USB_INT_HOSTDISCONNECT (1 << 0)
-
-#define CARKIT_CTRL 0x19
-#define CARKIT_CTRL_SET 0x1A
-#define CARKIT_CTRL_CLR 0x1B
-#define CARKIT_CTRL_MICEN (1 << 6)
-#define CARKIT_CTRL_SPKRIGHTEN (1 << 5)
-#define CARKIT_CTRL_SPKLEFTEN (1 << 4)
-#define CARKIT_CTRL_RXDEN (1 << 3)
-#define CARKIT_CTRL_TXDEN (1 << 2)
-#define CARKIT_CTRL_IDGNDDRV (1 << 1)
-#define CARKIT_CTRL_CARKITPWR (1 << 0)
-#define CARKIT_PLS_CTRL 0x22
-#define CARKIT_PLS_CTRL_SET 0x23
-#define CARKIT_PLS_CTRL_CLR 0x24
-#define CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3)
-#define CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
-#define CARKIT_PLS_CTRL_RXPLSEN (1 << 1)
-#define CARKIT_PLS_CTRL_TXPLSEN (1 << 0)
-
-#define MCPC_CTRL 0x30
-#define MCPC_CTRL_SET 0x31
-#define MCPC_CTRL_CLR 0x32
-#define MCPC_CTRL_RTSOL (1 << 7)
-#define MCPC_CTRL_EXTSWR (1 << 6)
-#define MCPC_CTRL_EXTSWC (1 << 5)
-#define MCPC_CTRL_VOICESW (1 << 4)
-#define MCPC_CTRL_OUT64K (1 << 3)
-#define MCPC_CTRL_RTSCTSSW (1 << 2)
-#define MCPC_CTRL_HS_UART (1 << 0)
-
-#define MCPC_IO_CTRL 0x33
-#define MCPC_IO_CTRL_SET 0x34
-#define MCPC_IO_CTRL_CLR 0x35
-#define MCPC_IO_CTRL_MICBIASEN (1 << 5)
-#define MCPC_IO_CTRL_CTS_NPU (1 << 4)
-#define MCPC_IO_CTRL_RXD_PU (1 << 3)
-#define MCPC_IO_CTRL_TXDTYP (1 << 2)
-#define MCPC_IO_CTRL_CTSTYP (1 << 1)
-#define MCPC_IO_CTRL_RTSTYP (1 << 0)
-
-#define MCPC_CTRL2 0x36
-#define MCPC_CTRL2_SET 0x37
-#define MCPC_CTRL2_CLR 0x38
-#define MCPC_CTRL2_MCPC_CK_EN (1 << 0)
-
-#define OTHER_FUNC_CTRL 0x80
-#define OTHER_FUNC_CTRL_SET 0x81
-#define OTHER_FUNC_CTRL_CLR 0x82
-#define OTHER_FUNC_CTRL_BDIS_ACON_EN (1 << 4)
-#define OTHER_FUNC_CTRL_FIVEWIRE_MODE (1 << 2)
-
-#define OTHER_IFC_CTRL 0x83
-#define OTHER_IFC_CTRL_SET 0x84
-#define OTHER_IFC_CTRL_CLR 0x85
-#define OTHER_IFC_CTRL_OE_INT_EN (1 << 6)
-#define OTHER_IFC_CTRL_CEA2011_MODE (1 << 5)
-#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN (1 << 4)
-#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT (1 << 3)
-#define OTHER_IFC_CTRL_HIZ_ULPI (1 << 2)
-#define OTHER_IFC_CTRL_ALT_INT_REROUTE (1 << 0)
-
-#define OTHER_INT_EN_RISE 0x86
-#define OTHER_INT_EN_RISE_SET 0x87
-#define OTHER_INT_EN_RISE_CLR 0x88
-#define OTHER_INT_EN_FALL 0x89
-#define OTHER_INT_EN_FALL_SET 0x8A
-#define OTHER_INT_EN_FALL_CLR 0x8B
-#define OTHER_INT_STS 0x8C
-#define OTHER_INT_LATCH 0x8D
-#define OTHER_INT_VB_SESS_VLD (1 << 7)
-#define OTHER_INT_DM_HI (1 << 6) /* not valid for
"latch" reg */
-#define OTHER_INT_DP_HI (1 << 5) /* not valid for
"latch" reg */
-#define OTHER_INT_BDIS_ACON (1 << 3) /* not valid for "fall" regs */
-#define OTHER_INT_MANU (1 << 1)
-#define OTHER_INT_ABNORMAL_STRESS (1 << 0)
-
-#define ID_STATUS 0x96
-#define ID_RES_FLOAT (1 << 4)
-#define ID_RES_440K (1 << 3)
-#define ID_RES_200K (1 << 2)
-#define ID_RES_102K (1 << 1)
-#define ID_RES_GND (1 << 0)
-
-#define POWER_CTRL 0xAC
-#define POWER_CTRL_SET 0xAD
-#define POWER_CTRL_CLR 0xAE
-#define POWER_CTRL_OTG_ENAB (1 << 5)
-
-#define OTHER_IFC_CTRL2 0xAF
-#define OTHER_IFC_CTRL2_SET 0xB0
-#define OTHER_IFC_CTRL2_CLR 0xB1
-#define OTHER_IFC_CTRL2_ULPI_STP_LOW (1 << 4)
-#define OTHER_IFC_CTRL2_ULPI_TXEN_POL (1 << 3)
-#define OTHER_IFC_CTRL2_ULPI_4PIN_2430 (1 << 2)
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK (3 << 0) /* bits 0 and 1 */
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N (0 << 0)
-#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N (1 << 0)
-
-#define REG_CTRL_EN 0xB2
-#define REG_CTRL_EN_SET 0xB3
-#define REG_CTRL_EN_CLR 0xB4
-#define REG_CTRL_ERROR 0xB5
-#define ULPI_I2C_CONFLICT_INTEN (1 << 0)
-
-#define OTHER_FUNC_CTRL2 0xB8
-#define OTHER_FUNC_CTRL2_SET 0xB9
-#define OTHER_FUNC_CTRL2_CLR 0xBA
-#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN (1 << 0)
-
-/* following registers do not have separate _clr and _set registers */
-#define VBUS_DEBOUNCE 0xC0
-#define ID_DEBOUNCE 0xC1
-#define VBAT_TIMER 0xD3
-#define PHY_PWR_CTRL 0xFD
-#define PHY_PWR_PHYPWD (1 << 0)
-#define PHY_CLK_CTRL 0xFE
-#define PHY_CLK_CTRL_CLOCKGATING_EN (1 << 2)
-#define PHY_CLK_CTRL_CLK32K_EN (1 << 1)
-#define REQ_PHY_DPLL_CLK (1 << 0)
-#define PHY_CLK_CTRL_STS 0xFF
-#define PHY_DPLL_CLK (1 << 0)
-
-/* In module TWL4030_MODULE_PM_MASTER */
-#define PROTECT_KEY 0x0E
-
-/* In module TWL4030_MODULE_PM_RECEIVER */
-#define VUSB_DEDICATED1 0x7D
-#define VUSB_DEDICATED2 0x7E
-#define VUSB1V5_DEV_GRP 0x71
-#define VUSB1V5_TYPE 0x72
-#define VUSB1V5_REMAP 0x73
-#define VUSB1V8_DEV_GRP 0x74
-#define VUSB1V8_TYPE 0x75
-#define VUSB1V8_REMAP 0x76
-#define VUSB3V1_DEV_GRP 0x77
-#define VUSB3V1_TYPE 0x78
-#define VUSB3V1_REMAP 0x79
-
-#define ID_STATUS 0x96
-#define ID_RES_FLOAT (1 << 4) /* mini-B */
-#define ID_RES_440K (1 << 3) /* type 2 charger */
-#define ID_RES_200K (1 << 2) /* 5-wire carkit or
- type 1 charger */
-#define ID_RES_102K (1 << 1) /* phone */
-#define ID_RES_GND (1 << 0) /* mini-A */
-
-/* In module TWL4030_MODULE_INTBR */
-#define PMBR1 0x0D
-#define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
-
-/* In module TWL4030_MODULE_INT */
-#define REG_PWR_ISR1 0x00
-#define REG_PWR_IMR1 0x01
-#define USB_PRES (1 << 2)
-#define REG_PWR_EDR1 0x05
-#define USB_PRES_FALLING (1 << 4)
-#define USB_PRES_RISING (1 << 5)
-#define REG_PWR_SIH_CTRL 0x07
-#define COR (1 << 2)
-
-/* internal define on top of container_of */
-#define xceiv_to_twl(x) container_of((x), struct twl4030_usb,
otg);
-
-/* bits in OTG_CTRL */
-
-#define OTG_XCEIV_OUTPUTS \
- (OTG_ASESSVLD|OTG_BSESSEND|OTG_BSESSVLD|OTG_VBUSVLD|OTG_ID)
-#define OTG_XCEIV_INPUTS \
- (OTG_PULLDOWN|OTG_PULLUP|OTG_DRV_VBUS|OTG_PD_VBUS|OTG_PU_VBUS|OTG_PU_ID)
-#define OTG_CTRL_BITS \
- (OTG_A_BUSREQ|OTG_A_SETB_HNPEN|OTG_B_BUSREQ|OTG_B_HNPEN|OTG_BUSDROP)
- /* and OTG_PULLUP is sometimes written */
-
-#define OTG_CTRL_MASK (OTG_DRIVER_SEL| \
- OTG_XCEIV_OUTPUTS|OTG_XCEIV_INPUTS| \
- OTG_CTRL_BITS)
-
-
-/*-------------------------------------------------------------------------*/
-
struct twl4030_usb {
struct otg_transceiver otg;
+ struct device *dev;
+
+ /* pin configuration */
+ enum twl4030_usb_mode usb_mode;
int irq;
- u8 usb_mode; /* pin configuration */
-#define T2_USB_MODE_ULPI 1
-/* #define T2_USB_MODE_CEA2011_3PIN 2 */
u8 asleep;
};
-static struct twl4030_usb *the_transceiver;
+/* internal define on top of container_of */
+#define xceiv_to_twl(x) container_of((x), struct twl4030_usb,
otg);
/*-------------------------------------------------------------------------*/
-static int twl4030_i2c_write_u8_verify(u8 module, u8 data, u8 address)
+static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
+ u8 module, u8 data, u8 address)
{
u8 check;
@@ -297,46 +68,51 @@ static int twl4030_i2c_write_u8_verify(u8 module, u8 data,
u8 address)
(check == data))
return 0;
/* Failed again: Return error */
+
return -EBUSY;
}
-#define twl4030_usb_write_verify(address, data) \
- twl4030_i2c_write_u8_verify(TWL4030_MODULE_USB, (data), (address))
+#define twl4030_usb_write_verify(twl, address, data) \
+ twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_USB, (data), (address))
-static inline int twl4030_usb_write(u8 address, u8 data)
+static inline int twl4030_usb_write(struct twl4030_usb *twl,
+ u8 address, u8 data)
{
int ret = 0;
+
ret = twl4030_i2c_write_u8(TWL4030_MODULE_USB, data, address);
if (ret >= 0) {
#if 0 /* debug */
u8 data1;
if (twl4030_i2c_read_u8(TWL4030_MODULE_USB, &data1,
address) < 0)
- printk(KERN_ERR "re-read failed\n");
+ dev_err(twl->dev, "re-read failed\n");
else
- printk(KERN_INFO
+ dev_dbg(twl->dev,
"Write %s wrote %x read %x from reg %x\n",
(data1 == data) ? "succeed" : "mismatch",
data, data1, address);
#endif
} else {
- printk(KERN_WARNING
+ dev_warn(twl->dev,
"TWL4030:USB:Write[0x%x] Error %d\n", address, ret);
}
+
return ret;
}
-static inline int twl4030_usb_read(u8 address)
+static inline int twl4030_usb_read(struct twl4030_usb *twl, u8 address)
{
u8 data;
int ret = 0;
+
ret = twl4030_i2c_read_u8(TWL4030_MODULE_USB, &data, address);
- if (ret >= 0) {
+ if (ret >= 0)
ret = data;
- } else {
- printk(KERN_WARNING
+ else
+ dev_warn(twl->dev,
"TWL4030:USB:Read[0x%x] Error %d\n", address, ret);
- }
+
return ret;
}
@@ -345,14 +121,13 @@ static inline int twl4030_usb_read(u8 address)
static inline int
twl4030_usb_set_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
{
- return twl4030_usb_write(reg + 1, bits);
+ return twl4030_usb_write(twl, reg + 1, bits);
}
static inline int
twl4030_usb_clear_bits(struct twl4030_usb *twl, u8 reg, u8 bits)
{
- return twl4030_usb_write(reg + 2, bits);
-
+ return twl4030_usb_write(twl, reg + 2, bits);
}
/*-------------------------------------------------------------------------*/
@@ -380,185 +155,130 @@ static void twl4030_usb_set_mode(struct twl4030_usb
*twl, int mode)
};
}
-#ifdef CONFIG_TWL4030_USB_HS_ULPI
-static void hs_usb_init(struct twl4030_usb *twl)
-{
- twl->usb_mode = T2_USB_MODE_ULPI;
- return;
-}
-
-#endif
-
-static void twl4030_i2c_access(int on)
+static void twl4030_i2c_access(struct twl4030_usb *twl, int on)
{
unsigned long timeout;
- int val = twl4030_usb_read(PHY_CLK_CTRL);
+ int val = twl4030_usb_read(twl, PHY_CLK_CTRL);
if (val >= 0) {
if (on) {
/* enable DPLL to access PHY registers over I2C */
val |= REQ_PHY_DPLL_CLK;
- if (twl4030_usb_write_verify(PHY_CLK_CTRL,
- (u8)val) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+ (u8)val) < 0);
timeout = jiffies + HZ;
- while (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
+ while (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK)
&& time_before(jiffies, timeout))
udelay(10);
- if (!(twl4030_usb_read(PHY_CLK_CTRL_STS) &
+ if (!(twl4030_usb_read(twl, PHY_CLK_CTRL_STS) &
PHY_DPLL_CLK))
- printk(KERN_ERR "Timeout setting T2 HSUSB "
+ dev_err(twl->dev, "Timeout setting T2 HSUSB "
"PHY DPLL clock\n");
} else {
/* let ULPI control the DPLL clock */
val &= ~REQ_PHY_DPLL_CLK;
- if (twl4030_usb_write_verify(PHY_CLK_CTRL,
- (u8)val) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- }
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_CLK_CTRL,
+ (u8)val) < 0);
}
}
- return;
}
-static void usb_irq_enable(int rising, int falling)
+static void usb_irq_enable(struct twl4030_usb *twl, int rising, int falling)
{
u8 val;
/* edge setup */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
+ &val, REG_PWR_EDR1) < 0);
+
val &= ~(USB_PRES_RISING | USB_PRES_FALLING);
if (rising)
val = val | USB_PRES_RISING;
if (falling)
val = val | USB_PRES_FALLING;
- if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
- REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_INT,
+ val, REG_PWR_EDR1) < 0);
/* un-mask interrupt */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_IMR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
+ &val, REG_PWR_IMR1) < 0);
+
val &= ~USB_PRES;
- if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
- REG_PWR_IMR1) < 0)
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
+ WARN_ON(twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_INT,
+ val, REG_PWR_IMR1) < 0);
}
-static void usb_irq_disable(void)
+static void usb_irq_disable(struct twl4030_usb *twl)
{
u8 val;
/* undo edge setup */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
+ &val, REG_PWR_EDR1) < 0);
val &= ~(USB_PRES_RISING | USB_PRES_FALLING);
- if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
- REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_INT,
+ val, REG_PWR_EDR1) < 0);
/* mask interrupt */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_IMR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- return;
- }
+ WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
+ &val, REG_PWR_IMR1) < 0);
val |= USB_PRES;
- if (twl4030_i2c_write_u8_verify(TWL4030_MODULE_INT, val,
- REG_PWR_IMR1) < 0)
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
+ WARN_ON(twl4030_i2c_write_u8_verify(twl, TWL4030_MODULE_INT,
+ val, REG_PWR_IMR1) < 0);
}
static void twl4030_phy_power(struct twl4030_usb *twl, int on)
{
u8 pwr;
- pwr = twl4030_usb_read(PHY_PWR_CTRL);
+ pwr = twl4030_usb_read(twl, PHY_PWR_CTRL);
if (on) {
pwr &= ~PHY_PWR_PHYPWD;
- if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- return;
- }
- twl4030_usb_write(PHY_CLK_CTRL,
- twl4030_usb_read(PHY_CLK_CTRL) |
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
+ twl4030_usb_write(twl, PHY_CLK_CTRL,
+ twl4030_usb_read(twl, PHY_CLK_CTRL) |
(PHY_CLK_CTRL_CLOCKGATING_EN |
PHY_CLK_CTRL_CLK32K_EN));
} else {
pwr |= PHY_PWR_PHYPWD;
- if (twl4030_usb_write_verify(PHY_PWR_CTRL, pwr) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c write failed,"
- " line %d\n", __LINE__);
- }
+ WARN_ON(twl4030_usb_write_verify(twl, PHY_PWR_CTRL, pwr) < 0);
}
- return;
}
-static void twl4030_phy_suspend(int controller_off)
+static void twl4030_phy_suspend(struct twl4030_usb *twl, int controller_off)
{
- struct twl4030_usb *twl = the_transceiver;
-
if (controller_off)
- usb_irq_disable();
+ usb_irq_disable(twl);
if (twl->asleep)
return;
if (!controller_off)
/* enable rising edge interrupt to detect cable attach */
- usb_irq_enable(1, 0);
+ usb_irq_enable(twl, 1, 0);
twl4030_phy_power(twl, 0);
twl->asleep = 1;
- return;
}
-static void twl4030_phy_resume(void)
+static void twl4030_phy_resume(struct twl4030_usb *twl)
{
- struct twl4030_usb *twl = the_transceiver;
-
if (!twl->asleep)
return;
/* enable falling edge interrupt to detect cable detach */
- usb_irq_enable(0, 1);
+ usb_irq_enable(twl, 0, 1);
twl4030_phy_power(twl, 1);
- twl4030_i2c_access(1);
+ twl4030_i2c_access(twl, 1);
twl4030_usb_set_mode(twl, twl->usb_mode);
if (twl->usb_mode == T2_USB_MODE_ULPI)
- twl4030_i2c_access(0);
+ twl4030_i2c_access(twl, 0);
twl->asleep = 0;
- return;
}
static void twl4030_usb_ldo_init(struct twl4030_usb *twl)
@@ -591,59 +311,57 @@ static void twl4030_usb_ldo_init(struct twl4030_usb *twl)
static irqreturn_t twl4030_usb_irq(int irq, void *_twl)
{
- int ret = IRQ_NONE;
+ struct twl4030_usb *twl = _twl;
u8 val;
/* action based on cable attach or detach */
- if (twl4030_i2c_read_u8(TWL4030_MODULE_INT, &val, REG_PWR_EDR1) < 0) {
- printk(KERN_ERR "twl4030_usb: i2c read failed,"
- " line %d\n", __LINE__);
- goto done;
- }
+ WARN_ON(twl4030_i2c_read_u8(TWL4030_MODULE_INT,
+ &val, REG_PWR_EDR1) < 0);
if (val & USB_PRES_RISING) {
- twl4030_phy_resume();
+ twl4030_phy_resume(twl);
twl4030charger_usb_en(1);
} else {
twl4030charger_usb_en(0);
- twl4030_phy_suspend(0);
+ twl4030_phy_suspend(twl, 0);
}
- ret = IRQ_HANDLED;
-
-done:
- return ret;
+ return IRQ_HANDLED;
}
static int twl4030_set_suspend(struct otg_transceiver *x, int suspend)
{
+ struct twl4030_usb *twl = xceiv_to_twl(x);
+
if (suspend)
- twl4030_phy_suspend(1);
+ twl4030_phy_suspend(twl, 1);
else
- twl4030_phy_resume();
+ twl4030_phy_resume(twl);
return 0;
}
-static int twl4030_set_peripheral(struct otg_transceiver *xceiv,
+static int twl4030_set_peripheral(struct otg_transceiver *x,
struct usb_gadget *gadget)
{
+ struct twl4030_usb *twl;
u32 l;
- struct twl4030_usb *twl = xceiv_to_twl(xceiv);
- if (!xceiv)
+ if (!x)
return -ENODEV;
+ twl = xceiv_to_twl(x);
+
if (!gadget) {
omap_writew(0, OTG_IRQ_EN);
- twl4030_phy_suspend(1);
+ twl4030_phy_suspend(twl, 1);
twl->otg.gadget = NULL;
return -ENODEV;
}
twl->otg.gadget = gadget;
- twl4030_phy_resume();
+ twl4030_phy_resume(twl);
l = omap_readl(OTG_CTRL) & OTG_CTRL_MASK;
l &= ~(OTG_XCEIV_OUTPUTS|OTG_CTRL_BITS);
@@ -660,23 +378,25 @@ static int twl4030_set_peripheral(struct otg_transceiver
*xceiv,
return 0;
}
-static int twl4030_set_host(struct otg_transceiver *xceiv, struct usb_bus
*host)
+static int twl4030_set_host(struct otg_transceiver *x, struct usb_bus *host)
{
- struct twl4030_usb *twl = xceiv_to_twl(xceiv);
+ struct twl4030_usb *twl;
- if (!xceiv)
+ if (!x)
return -ENODEV;
+ twl = xceiv_to_twl(x);
+
if (!host) {
omap_writew(0, OTG_IRQ_EN);
- twl4030_phy_suspend(1);
+ twl4030_phy_suspend(twl, 1);
twl->otg.host = NULL;
return -ENODEV;
}
twl->otg.host = host;
- twl4030_phy_resume();
+ twl4030_phy_resume(twl);
twl4030_usb_set_bits(twl, TWL4030_OTG_CTRL,
TWL4030_OTG_CTRL_DMPULLDOWN
@@ -689,63 +409,65 @@ static int twl4030_set_host(struct otg_transceiver
*xceiv, struct usb_bus *host)
return 0;
}
-static int __init twl4030_usb_init(void)
+static int __init twl4030_usb_probe(struct platform_device *pdev)
{
+ struct twl4030_usb_platform_data *pdata = pdev->dev.platform_data;
struct twl4030_usb *twl;
int status;
- if (the_transceiver)
- return 0;
-
twl = kzalloc(sizeof *twl, GFP_KERNEL);
if (!twl)
- return 0;
-
- the_transceiver = twl;
+ return -ENOMEM;
+ twl->dev = &pdev->dev;
twl->irq = TWL4030_PWRIRQ_USB_PRES;
twl->otg.set_host = twl4030_set_host;
twl->otg.set_peripheral = twl4030_set_peripheral;
twl->otg.set_suspend = twl4030_set_suspend;
- usb_irq_disable();
+ if (!pdata) {
+ dev_info(&pdev->dev, "platform_data not available, defaulting"
+ " to ULPI mode\n");
+ twl->usb_mode = T2_USB_MODE_ULPI;
+ } else {
+ twl->usb_mode = pdata->usb_mode;
+ }
+
+ usb_irq_disable(twl);
status = request_irq(twl->irq, twl4030_usb_irq, 0, "twl4030_usb", twl);
if (status < 0) {
- printk(KERN_DEBUG "can't get IRQ %d, err %d\n",
+ dev_dbg(&pdev->dev, "can't get IRQ %d, err %d\n",
twl->irq, status);
kfree(twl);
- return -ENODEV;
+ return status;
}
-#if defined(CONFIG_TWL4030_USB_HS_ULPI)
- hs_usb_init(twl);
-#endif
+
twl4030_usb_ldo_init(twl);
twl4030_phy_power(twl, 1);
- twl4030_i2c_access(1);
+ twl4030_i2c_access(twl, 1);
twl4030_usb_set_mode(twl, twl->usb_mode);
- if (twl->usb_mode == T2_USB_MODE_ULPI)
- twl4030_i2c_access(0);
twl->asleep = 0;
- if (twl->usb_mode == T2_USB_MODE_ULPI)
- twl4030_phy_suspend(1);
+ if (twl->usb_mode == T2_USB_MODE_ULPI) {
+ twl4030_i2c_access(twl, 0);
+ twl4030_phy_suspend(twl, 0);
+ }
otg_set_transceiver(&twl->otg);
-
- printk(KERN_INFO "Initialized TWL4030 USB module\n");
+ dev_set_drvdata(&pdev->dev, twl);
+ dev_info(&pdev->dev, "Initialized TWL4030 USB module\n");
return 0;
}
-
-static void __exit twl4030_usb_exit(void)
+static int __exit twl4030_usb_remove(struct platform_device *pdev)
{
- struct twl4030_usb *twl = the_transceiver;
+ struct twl4030_usb *twl = dev_get_drvdata(&pdev->dev);
int val;
- usb_irq_disable();
+ usb_irq_disable(twl);
free_irq(twl->irq, twl);
/* set transceiver mode to power on defaults */
@@ -755,11 +477,11 @@ static void __exit twl4030_usb_exit(void)
* clear dpll clock request for i2c access,
* disable 32KHz
*/
- val = twl4030_usb_read(PHY_CLK_CTRL);
+ val = twl4030_usb_read(twl, PHY_CLK_CTRL);
if (val >= 0) {
val |= PHY_CLK_CTRL_CLOCKGATING_EN;
val &= ~(PHY_CLK_CTRL_CLK32K_EN | REQ_PHY_DPLL_CLK);
- twl4030_usb_write(PHY_CLK_CTRL, (u8)val);
+ twl4030_usb_write(twl, PHY_CLK_CTRL, (u8)val);
}
/* disable complete OTG block */
@@ -768,12 +490,32 @@ static void __exit twl4030_usb_exit(void)
twl4030_phy_power(twl, 0);
kfree(twl);
+
+ return 0;
+}
+
+static struct platform_driver twl4030_driver = {
+ .probe = twl4030_usb_probe,
+ .remove = __exit_p(twl4030_remove),
+ .driver = {
+ .name = "twl4030-usb",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init twl4030_usb_init(void)
+{
+ return platform_driver_register(&twl4030_driver);
}
+module_init(twl4030_usb_init);
-subsys_initcall(twl4030_usb_init);
+static void __exit twl4030_usb_exit(void)
+{
+ platform_driver_unregister(&twl4030_driver);
+}
module_exit(twl4030_usb_exit);
-MODULE_ALIAS("i2c:twl4030-usb");
-MODULE_AUTHOR("Texas Instruments, Inc.");
+MODULE_ALIAS("platform:twl4030-usb");
+MODULE_AUTHOR("Texas Instruments, Inc, Nokia Corporation");
MODULE_DESCRIPTION("TWL4030 USB transceiver driver");
MODULE_LICENSE("GPL");
diff --git a/include/linux/i2c/twl4030-usb.h b/include/linux/i2c/twl4030-usb.h
new file mode 100644
index 0000000..9cd2e50
--- /dev/null
+++ b/include/linux/i2c/twl4030-usb.h
@@ -0,0 +1,257 @@
+/*
+ * twl4030-usb.h - header for TWL4030 USB Transceiver
+ *
+ * Copyright (C) 2004-2007 Texas Instruments
+ * Copyright (C) 2008 Nokia Corporation
+ * Contact: Felipe Balbi <[EMAIL PROTECTED]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#ifndef __TWL4030_USB_H_
+#define __TWL4030_USB_H_
+
+/* Register defines */
+
+#define VENDOR_ID_LO 0x00
+#define VENDOR_ID_HI 0x01
+#define PRODUCT_ID_LO 0x02
+#define PRODUCT_ID_HI 0x03
+
+#define FUNC_CTRL 0x04
+#define FUNC_CTRL_SET 0x05
+#define FUNC_CTRL_CLR 0x06
+#define FUNC_CTRL_SUSPENDM (1 << 6)
+#define FUNC_CTRL_RESET (1 << 5)
+#define FUNC_CTRL_OPMODE_MASK (3 << 3) /* bits 3 and 4 */
+#define FUNC_CTRL_OPMODE_NORMAL (0 << 3)
+#define FUNC_CTRL_OPMODE_NONDRIVING (1 << 3)
+#define FUNC_CTRL_OPMODE_DISABLE_BIT_NRZI (2 << 3)
+#define FUNC_CTRL_TERMSELECT (1 << 2)
+#define FUNC_CTRL_XCVRSELECT_MASK (3 << 0) /* bits 0 and 1 */
+#define FUNC_CTRL_XCVRSELECT_HS (0 << 0)
+#define FUNC_CTRL_XCVRSELECT_FS (1 << 0)
+#define FUNC_CTRL_XCVRSELECT_LS (2 << 0)
+#define FUNC_CTRL_XCVRSELECT_FS4LS (3 << 0)
+
+#define IFC_CTRL 0x07
+#define IFC_CTRL_SET 0x08
+#define IFC_CTRL_CLR 0x09
+#define IFC_CTRL_INTERFACE_PROTECT_DISABLE (1 << 7)
+#define IFC_CTRL_AUTORESUME (1 << 4)
+#define IFC_CTRL_CLOCKSUSPENDM (1 << 3)
+#define IFC_CTRL_CARKITMODE (1 << 2)
+#define IFC_CTRL_FSLSSERIALMODE_3PIN (1 << 1)
+
+#define TWL4030_OTG_CTRL 0x0A
+#define TWL4030_OTG_CTRL_SET 0x0B
+#define TWL4030_OTG_CTRL_CLR 0x0C
+#define TWL4030_OTG_CTRL_DRVVBUS (1 << 5)
+#define TWL4030_OTG_CTRL_CHRGVBUS (1 << 4)
+#define TWL4030_OTG_CTRL_DISCHRGVBUS (1 << 3)
+#define TWL4030_OTG_CTRL_DMPULLDOWN (1 << 2)
+#define TWL4030_OTG_CTRL_DPPULLDOWN (1 << 1)
+#define TWL4030_OTG_CTRL_IDPULLUP (1 << 0)
+
+#define USB_INT_EN_RISE 0x0D
+#define USB_INT_EN_RISE_SET 0x0E
+#define USB_INT_EN_RISE_CLR 0x0F
+#define USB_INT_EN_FALL 0x10
+#define USB_INT_EN_FALL_SET 0x11
+#define USB_INT_EN_FALL_CLR 0x12
+#define USB_INT_STS 0x13
+#define USB_INT_LATCH 0x14
+#define USB_INT_IDGND (1 << 4)
+#define USB_INT_SESSEND (1 << 3)
+#define USB_INT_SESSVALID (1 << 2)
+#define USB_INT_VBUSVALID (1 << 1)
+#define USB_INT_HOSTDISCONNECT (1 << 0)
+
+#define CARKIT_CTRL 0x19
+#define CARKIT_CTRL_SET 0x1A
+#define CARKIT_CTRL_CLR 0x1B
+#define CARKIT_CTRL_MICEN (1 << 6)
+#define CARKIT_CTRL_SPKRIGHTEN (1 << 5)
+#define CARKIT_CTRL_SPKLEFTEN (1 << 4)
+#define CARKIT_CTRL_RXDEN (1 << 3)
+#define CARKIT_CTRL_TXDEN (1 << 2)
+#define CARKIT_CTRL_IDGNDDRV (1 << 1)
+#define CARKIT_CTRL_CARKITPWR (1 << 0)
+#define CARKIT_PLS_CTRL 0x22
+#define CARKIT_PLS_CTRL_SET 0x23
+#define CARKIT_PLS_CTRL_CLR 0x24
+#define CARKIT_PLS_CTRL_SPKRRIGHT_BIASEN (1 << 3)
+#define CARKIT_PLS_CTRL_SPKRLEFT_BIASEN (1 << 2)
+#define CARKIT_PLS_CTRL_RXPLSEN (1 << 1)
+#define CARKIT_PLS_CTRL_TXPLSEN (1 << 0)
+
+#define MCPC_CTRL 0x30
+#define MCPC_CTRL_SET 0x31
+#define MCPC_CTRL_CLR 0x32
+#define MCPC_CTRL_RTSOL (1 << 7)
+#define MCPC_CTRL_EXTSWR (1 << 6)
+#define MCPC_CTRL_EXTSWC (1 << 5)
+#define MCPC_CTRL_VOICESW (1 << 4)
+#define MCPC_CTRL_OUT64K (1 << 3)
+#define MCPC_CTRL_RTSCTSSW (1 << 2)
+#define MCPC_CTRL_HS_UART (1 << 0)
+
+#define MCPC_IO_CTRL 0x33
+#define MCPC_IO_CTRL_SET 0x34
+#define MCPC_IO_CTRL_CLR 0x35
+#define MCPC_IO_CTRL_MICBIASEN (1 << 5)
+#define MCPC_IO_CTRL_CTS_NPU (1 << 4)
+#define MCPC_IO_CTRL_RXD_PU (1 << 3)
+#define MCPC_IO_CTRL_TXDTYP (1 << 2)
+#define MCPC_IO_CTRL_CTSTYP (1 << 1)
+#define MCPC_IO_CTRL_RTSTYP (1 << 0)
+
+#define MCPC_CTRL2 0x36
+#define MCPC_CTRL2_SET 0x37
+#define MCPC_CTRL2_CLR 0x38
+#define MCPC_CTRL2_MCPC_CK_EN (1 << 0)
+
+#define OTHER_FUNC_CTRL 0x80
+#define OTHER_FUNC_CTRL_SET 0x81
+#define OTHER_FUNC_CTRL_CLR 0x82
+#define OTHER_FUNC_CTRL_BDIS_ACON_EN (1 << 4)
+#define OTHER_FUNC_CTRL_FIVEWIRE_MODE (1 << 2)
+
+#define OTHER_IFC_CTRL 0x83
+#define OTHER_IFC_CTRL_SET 0x84
+#define OTHER_IFC_CTRL_CLR 0x85
+#define OTHER_IFC_CTRL_OE_INT_EN (1 << 6)
+#define OTHER_IFC_CTRL_CEA2011_MODE (1 << 5)
+#define OTHER_IFC_CTRL_FSLSSERIALMODE_4PIN (1 << 4)
+#define OTHER_IFC_CTRL_HIZ_ULPI_60MHZ_OUT (1 << 3)
+#define OTHER_IFC_CTRL_HIZ_ULPI (1 << 2)
+#define OTHER_IFC_CTRL_ALT_INT_REROUTE (1 << 0)
+
+#define OTHER_INT_EN_RISE 0x86
+#define OTHER_INT_EN_RISE_SET 0x87
+#define OTHER_INT_EN_RISE_CLR 0x88
+#define OTHER_INT_EN_FALL 0x89
+#define OTHER_INT_EN_FALL_SET 0x8A
+#define OTHER_INT_EN_FALL_CLR 0x8B
+#define OTHER_INT_STS 0x8C
+#define OTHER_INT_LATCH 0x8D
+#define OTHER_INT_VB_SESS_VLD (1 << 7)
+#define OTHER_INT_DM_HI (1 << 6) /* not valid for
"latch" reg */
+#define OTHER_INT_DP_HI (1 << 5) /* not valid for
"latch" reg */
+#define OTHER_INT_BDIS_ACON (1 << 3) /* not valid for "fall" regs */
+#define OTHER_INT_MANU (1 << 1)
+#define OTHER_INT_ABNORMAL_STRESS (1 << 0)
+
+#define ID_STATUS 0x96
+#define ID_RES_FLOAT (1 << 4)
+#define ID_RES_440K (1 << 3)
+#define ID_RES_200K (1 << 2)
+#define ID_RES_102K (1 << 1)
+#define ID_RES_GND (1 << 0)
+
+#define POWER_CTRL 0xAC
+#define POWER_CTRL_SET 0xAD
+#define POWER_CTRL_CLR 0xAE
+#define POWER_CTRL_OTG_ENAB (1 << 5)
+
+#define OTHER_IFC_CTRL2 0xAF
+#define OTHER_IFC_CTRL2_SET 0xB0
+#define OTHER_IFC_CTRL2_CLR 0xB1
+#define OTHER_IFC_CTRL2_ULPI_STP_LOW (1 << 4)
+#define OTHER_IFC_CTRL2_ULPI_TXEN_POL (1 << 3)
+#define OTHER_IFC_CTRL2_ULPI_4PIN_2430 (1 << 2)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_MASK (3 << 0) /* bits 0 and 1 */
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT1N (0 << 0)
+#define OTHER_IFC_CTRL2_USB_INT_OUTSEL_INT2N (1 << 0)
+
+#define REG_CTRL_EN 0xB2
+#define REG_CTRL_EN_SET 0xB3
+#define REG_CTRL_EN_CLR 0xB4
+#define REG_CTRL_ERROR 0xB5
+#define ULPI_I2C_CONFLICT_INTEN (1 << 0)
+
+#define OTHER_FUNC_CTRL2 0xB8
+#define OTHER_FUNC_CTRL2_SET 0xB9
+#define OTHER_FUNC_CTRL2_CLR 0xBA
+#define OTHER_FUNC_CTRL2_VBAT_TIMER_EN (1 << 0)
+
+/* following registers do not have separate _clr and _set registers */
+#define VBUS_DEBOUNCE 0xC0
+#define ID_DEBOUNCE 0xC1
+#define VBAT_TIMER 0xD3
+#define PHY_PWR_CTRL 0xFD
+#define PHY_PWR_PHYPWD (1 << 0)
+#define PHY_CLK_CTRL 0xFE
+#define PHY_CLK_CTRL_CLOCKGATING_EN (1 << 2)
+#define PHY_CLK_CTRL_CLK32K_EN (1 << 1)
+#define REQ_PHY_DPLL_CLK (1 << 0)
+#define PHY_CLK_CTRL_STS 0xFF
+#define PHY_DPLL_CLK (1 << 0)
+
+/* In module TWL4030_MODULE_PM_MASTER */
+#define PROTECT_KEY 0x0E
+
+/* In module TWL4030_MODULE_PM_RECEIVER */
+#define VUSB_DEDICATED1 0x7D
+#define VUSB_DEDICATED2 0x7E
+#define VUSB1V5_DEV_GRP 0x71
+#define VUSB1V5_TYPE 0x72
+#define VUSB1V5_REMAP 0x73
+#define VUSB1V8_DEV_GRP 0x74
+#define VUSB1V8_TYPE 0x75
+#define VUSB1V8_REMAP 0x76
+#define VUSB3V1_DEV_GRP 0x77
+#define VUSB3V1_TYPE 0x78
+#define VUSB3V1_REMAP 0x79
+
+/* In module TWL4030_MODULE_INTBR */
+#define PMBR1 0x0D
+#define GPIO_USB_4PIN_ULPI_2430C (3 << 0)
+
+/* In module TWL4030_MODULE_INT */
+#define REG_PWR_ISR1 0x00
+#define REG_PWR_IMR1 0x01
+#define USB_PRES (1 << 2)
+#define REG_PWR_EDR1 0x05
+#define USB_PRES_FALLING (1 << 4)
+#define USB_PRES_RISING (1 << 5)
+#define REG_PWR_SIH_CTRL 0x07
+#define COR (1 << 2)
+
+/* bits in OTG_CTRL */
+#define OTG_XCEIV_OUTPUTS \
+ (OTG_ASESSVLD|OTG_BSESSEND|OTG_BSESSVLD|OTG_VBUSVLD|OTG_ID)
+#define OTG_XCEIV_INPUTS \
+ (OTG_PULLDOWN|OTG_PULLUP|OTG_DRV_VBUS|OTG_PD_VBUS|OTG_PU_VBUS|OTG_PU_ID)
+#define OTG_CTRL_BITS \
+ (OTG_A_BUSREQ|OTG_A_SETB_HNPEN|OTG_B_BUSREQ|OTG_B_HNPEN|OTG_BUSDROP)
+ /* and OTG_PULLUP is sometimes written */
+
+#define OTG_CTRL_MASK (OTG_DRIVER_SEL| \
+ OTG_XCEIV_OUTPUTS|OTG_XCEIV_INPUTS| \
+ OTG_CTRL_BITS)
+
+enum twl4030_usb_mode {
+ T2_USB_MODE_ULPI = 1,
+ T2_USB_MODE_CEA2011_3PIN = 2,
+};
+
+struct twl4030_usb_platform_data {
+ enum twl4030_usb_mode usb_mode;
+};
+
+#endif /* End of __TWL4030_USB_H */
+
--
1.6.0.1.126.ga118
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
