Apparently some versions of nolo don't mux the necessary GPMC pins for the smc91x probe to work properly. Let's fix this issue by adding mux support for GPMC to the kernel.
Note that it's unclear why the GPMC clk pin has input enabled, but let's not touch that as in general the mux settings in nolo are correct. Cc: Kevin Hilman <[email protected]> Cc: Roger Quadros <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> --- arch/arm/boot/dts/omap3-n900.dts | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 739fcf2..e7210d1 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -142,6 +142,33 @@ >; }; + gpmc_pins: pinmux_gpmc_pins { + pinctrl-single,pins = < + + /* address lines */ + OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */ + OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */ + OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */ + + /* data lines, gpmc_d0..d7 not muxable according to TRM */ + OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */ + OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */ + OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */ + OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */ + OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */ + OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */ + OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */ + OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */ + + /* + * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable + * according to TRM. REVISIT: why does nolo set input for gpmc_clk? + */ + OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */ + OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */ @@ -588,6 +615,8 @@ ranges = <0 0 0x04000000 0x10000000>; /* 256MB */ ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */ <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */ + pinctrl-names = "default"; + pinctrl-0 = <&gpmc_pins>; /* gpio-irq for dma: 65 */ -- 2.1.1 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
