* Roger Quadros <[email protected]> [141030 05:01]: > On 10/30/2014 02:28 AM, Tony Lindgren wrote: > > + > > + /* > > + * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, > > gpmc_wait0 not muxable > > + * according to TRM. REVISIT: why does nolo set input > > for gpmc_clk? > > + */ > > + OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) > > /* gpmc_ncs1.gpmc_ncs1 */ > > + OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) > > /* gpmc_clk.gpmc_clk */ > > Right about the comment. GPMC_CLK should feed the CLK input of the OneNAND. > This needs to be an OUTPUT pin. > > Does OneNAND work when this pin is configured as output?
Does not seem to work, it produces onenand_wait: ECC error = 0xffff. It seems the clock needs to be copied to GPMC too in some cases. For MMC, there's the MMCSDIO2ADPCLKISEL option to copy the clock to account for level shifter latencies [1]. But in the OneNAND case I don't think there are any level shifters, and I don't think we have "copy clock" option for GPMC either in SCM so it somehow is automatic in GPMC. Anyways, updated patch below with wrong guessing removed. Regards, Tony [1] http://processors.wiki.ti.com/index.php/SD-MMC_Usage_Notes_on_OMAP35x_and_AM37x 8< -------------------- From: Tony Lindgren <[email protected]> Date: Wed, 29 Oct 2014 17:16:47 -0700 Subject: [PATCH] ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins Apparently some versions of nolo don't mux the all the necessary GPMC pins for the smc91x probe to work properly. Let's fix this issue by adding mux support for GPMC to the kernel. Note that GPMC clk needs input enabled for OnenNAND to work. Cc: Kevin Hilman <[email protected]> Cc: Roger Quadros <[email protected]> Signed-off-by: Tony Lindgren <[email protected]> --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -142,6 +142,33 @@ >; }; + gpmc_pins: pinmux_gpmc_pins { + pinctrl-single,pins = < + + /* address lines */ + OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */ + OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */ + OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */ + + /* data lines, gpmc_d0..d7 not muxable according to TRM */ + OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */ + OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */ + OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */ + OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */ + OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */ + OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */ + OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */ + OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */ + + /* + * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable + * according to TRM. OneNAND seems to require PIN_INPUT on clock. + */ + OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */ + OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0x18a (PIN_INPUT | MUX_MODE0) /* i2c1_scl */ @@ -588,6 +615,8 @@ ranges = <0 0 0x04000000 0x10000000>; /* 256MB */ ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */ <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */ + pinctrl-names = "default"; + pinctrl-0 = <&gpmc_pins>; /* gpio-irq for dma: 65 */ -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
