Add the necessary dss configuration to drive the startek lcd on CompuLab
sbc-t43 single board computer.
Signed-off-by: Nikita Kiryanov <nik...@compulab.co.il>
Cc: Tony Lindgren <t...@atomide.com>
Cc: Benoit Cousson <bcous...@baylibre.com>
Cc: Rob Herring <r...@kernel.org>
Cc: Mark Rutland <mark.rutl...@arm.com>
Cc: Pawel Moll <pawel.m...@arm.com>
Cc: Igor Grinberg <grinb...@compulab.co.il>
Cc: Dmitry Lifshitz <lifsh...@compulab.co.il>
Cc: Ian Campbell <ijc+devicet...@hellion.org.uk>
---
Changes in V2:
- No changes.
arch/arm/boot/dts/am437x-sbc-t43.dts | 65 ++++++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)
diff --git a/arch/arm/boot/dts/am437x-sbc-t43.dts
b/arch/arm/boot/dts/am437x-sbc-t43.dts
index 6b51151..5f750c0 100644
--- a/arch/arm/boot/dts/am437x-sbc-t43.dts
+++ b/arch/arm/boot/dts/am437x-sbc-t43.dts
@@ -12,6 +12,10 @@
/ {
model = "CompuLab CM-T43 on SB-SOM-T43";
compatible = "compulab,am437x-sbc-t43", "compulab,am437x-cm-t43",
"ti,am4372", "ti,am43";
+
+ aliases {
+ display0 = &lcd0;
+ };
};
&am43xx_pinmux {
@@ -28,6 +32,41 @@
>;
};
+ dss_pinctrl_default: dss_pinctrl_default {
+ pinctrl-single,pins = <
+ AM4372_IOPAD(0x9b0, PIN_OUTPUT_PULLUP | MUX_MODE2) /*
cam0 hd -> DSS DATA 23 */
+ AM4372_IOPAD(0x9b4, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9b8, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9bc, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9c0, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9c4, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9c8, PIN_OUTPUT_PULLUP | MUX_MODE2)
+ AM4372_IOPAD(0x9cc, PIN_OUTPUT_PULLUP | MUX_MODE2) /*
cam1 data 9 -> DSS DATA 16 */
+
+ AM4372_IOPAD(0x8a0, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS DATA 0 */
+ AM4372_IOPAD(0x8a4, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8a8, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8ac, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8b0, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8b4, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8b8, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8bc, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8c0, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8c4, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8c8, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8cc, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8d0, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8d4, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8d8, PIN_OUTPUT_PULLUP | MUX_MODE0)
+ AM4372_IOPAD(0x8dc, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS DATA 15 */
+ AM4372_IOPAD(0x8e0, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS VSYNC */
+ AM4372_IOPAD(0x8e4, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS HSYNC */
+ AM4372_IOPAD(0x8e8, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS PCLK */
+ AM4372_IOPAD(0x8ec, PIN_OUTPUT_PULLUP | MUX_MODE0) /*
DSS AC BIAS EN */
+ AM4372_IOPAD(0xa20, PIN_OUTPUT_PULLUP | MUX_MODE7)
+ >;
+ };
+
uart0_pins_default: uart0_pins_default {
pinctrl-single,pins = <
AM4372_IOPAD(0x968, DS0_PULL_UP_DOWN_EN | INPUT_EN |
MUX_MODE0)
@@ -99,6 +138,20 @@
wp-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
};
+&dss {
+ status = "ok";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_pinctrl_default>;
+
+ port {
+ dpi_lcd_out: endpoint@0 {
+ remote-endpoint = <&lcd_in>;
+ data-lines = <24>;
+ };
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_default>;
@@ -113,3 +166,15 @@
pinctrl-names = "default";
pinctrl-0 = <&usb2_phy2_default>;
};
+
+&lcd0 {
+ enable-gpios = <&pca9555 14 GPIO_ACTIVE_HIGH
+ &gpio4 28 GPIO_ACTIVE_HIGH>;
+
+ port {
+ lcd_in: endpoint {
+ remote-endpoint = <&dpi_lcd_out>;
+ data-lines = <24>;
+ };
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
