Hi,
Some comments and a fix to the omap mux code below.
* Adrian Hunter <adrian.hun...@nokia.com> [100113 03:39]:
> From 060702bca6c60dd0f63f4e82e381ae1b8b112dec Mon Sep 17 00:00:00 2001
> From: Adrian Hunter <adrian.hun...@nokia.com>
> Date: Tue, 5 Jan 2010 13:46:57 +0200
> Subject: [PATCH] omap_hsmmc: RX51: set padconfs to pull down when powering
> off eMMC
>
> It has been discovered that, when eMMC is powered off, current
> will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
> Configuring pads for off-mode does not help because eMMC is
> powered off independently of off-mode. Hence the pads are now
> re-configured when eMMC is powered on or off.
>
> Signed-off-by: Adrian Hunter <adrian.hun...@nokia.com>
> ---
> arch/arm/mach-omap2/board-rx51-peripherals.c | 27
> +++++++++++++++++++++++++-
> arch/arm/mach-omap2/hsmmc.c | 2 +
> arch/arm/mach-omap2/hsmmc.h | 2 +
> arch/arm/plat-omap/include/plat/control.h | 6 +++++
> arch/arm/plat-omap/include/plat/mmc.h | 1 +
> drivers/mmc/host/omap_hsmmc.c | 8 +++++++
> 6 files changed, 45 insertions(+), 1 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c
> b/arch/arm/mach-omap2/board-rx51-peripherals.c
> index b6318b1..4d9dbb4 100644
> --- a/arch/arm/mach-omap2/board-rx51-peripherals.c
> +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c
> @@ -32,6 +32,7 @@
> #include <plat/gpmc.h>
> #include <plat/onenand.h>
> #include <plat/gpmc-smc91x.h>
> +#include <plat/control.h>
>
> #include "mux.h"
> #include "hsmmc.h"
> @@ -225,6 +226,29 @@ static void rx51_mmc_set_pm_constraints(struct device
> *dev, int on)
> #define rx51_mmc_set_pm_constraints NULL
> #endif
>
> +/*
> + * Current flows to eMMC when eMMC is off and the data lines are pulled up,
> + * so pull them down. N.B. we pull 8 lines because we are using 8 lines.
> + */
> +static void rx51_mmc_2_pad_conf(struct device *dev, int slot, int power_on)
> +{
> + if (power_on) {
> + /* Pull up */
> + omap_ctrl_writew( 0x118, OMAP343X_PADCONF_MMC2_CMD);
> + omap_ctrl_writel(0x1180118, OMAP343X_PADCONF_MMC2_DAT0);
> + omap_ctrl_writel(0x1180118, OMAP343X_PADCONF_MMC2_DAT2);
> + omap_ctrl_writel(0x1180118, OMAP343X_PADCONF_MMC2_DAT4);
> + omap_ctrl_writel(0x1180118, OMAP343X_PADCONF_MMC2_DAT6);
> + } else {
> + /* Pull down */
> + omap_ctrl_writew( 0x108, OMAP343X_PADCONF_MMC2_CMD);
> + omap_ctrl_writel(0x1080108, OMAP343X_PADCONF_MMC2_DAT0);
> + omap_ctrl_writel(0x1080108, OMAP343X_PADCONF_MMC2_DAT2);
> + omap_ctrl_writel(0x1080108, OMAP343X_PADCONF_MMC2_DAT4);
> + omap_ctrl_writel(0x1080108, OMAP343X_PADCONF_MMC2_DAT6);
> + }
> +}
> +
> static struct omap2_hsmmc_info mmc[] __initdata = {
> {
> .name = "external",
We really want to do all the dynamic muxing using the mux code
instead of adding custom code. But as the mux signal names are dropped
during __init, we cannot use omap_mux_init_signal().
So could you please give the attached patch a try? With this patch
you should be able to do the dynamic remuxing like this:
/*
* Enable input logic and pull all lines up when eMMC is on.
*
* REVISIT: Are the defaul values OK for omap off-idle, or is
* OMAP_PIN_OFF_OUTPUT_LOW also needed to keep the pins down?
*/
static struct omap_board_mux mmc2_on_mux[] = {
OMAP3_MUX(SDMMC2_CMD, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT0, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT1, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT2, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT3, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT4, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT5, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT6, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT7, OMAP_PIN_INPUT_PULLUP | OMAP_MUX_MODE0),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
/*
* Disable input logic and pull all lines down when eMMC is off.
*
* REVISIT1: The input logic should not be needed here, just
* OMAP_PULL_ENA to pull the lines down. If that does not work,
* use OMAP_PIN_INPUT_PULLUP.
*
* REVISIT2: Are the default values OK for omap off-idle, or is
* OMAP_PIN_OFF_OUTPUT_LOW also needed to keep the pins down?
*/
static struct omap_board_mux mmc2_off_mux[] = {
OMAP3_MUX(SDMMC2_CMD, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT0, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT1, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT2, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT3, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT4, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT5, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT6, OMAP_PULL_ENA | OMAP_MUX_MODE0),
OMAP3_MUX(SDMMC2_DAT7, OMAP_PULL_ENA | OMAP_MUX_MODE0),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
static void mmc2_remux(struct device *dev, int slot, int power_on)
{
if (power_on)
omap_mux_write_array(mmc2_on_mux);
else
omap_mux_write_array(mmc2_off_mux);
}
You might want to check what happens in omap off-idle mode in these cases
and see if enabling OMAP_PIN_OFF_INPUT_PULLDOWN makes any difference in
power consumption in off state. That probably does not matter unless the
floating lines cause the eMMC to do something on it's own :)
Note that I've used "remux" instead of "pad_conf" to make it easier to
grep all the code for muxing, so maybe use "remux" instead in your updated
patch too?
> --- a/arch/arm/plat-omap/include/plat/control.h
> +++ b/arch/arm/plat-omap/include/plat/control.h
> @@ -183,6 +183,12 @@
> #define OMAP343X_PADCONF_ETK_D14 OMAP343X_PADCONF_ETK(16)
> #define OMAP343X_PADCONF_ETK_D15 OMAP343X_PADCONF_ETK(17)
>
> +#define OMAP343X_PADCONF_MMC2_CMD (OMAP2_CONTROL_PADCONFS + 0x12A)
> +#define OMAP343X_PADCONF_MMC2_DAT0 (OMAP2_CONTROL_PADCONFS + 0x12C)
> +#define OMAP343X_PADCONF_MMC2_DAT2 (OMAP2_CONTROL_PADCONFS + 0x130)
> +#define OMAP343X_PADCONF_MMC2_DAT4 (OMAP2_CONTROL_PADCONFS + 0x134)
> +#define OMAP343X_PADCONF_MMC2_DAT6 (OMAP2_CONTROL_PADCONFS + 0x138)
> +
> /* 34xx GENERAL_WKUP regist offsets */
> #define OMAP343X_CONTROL_WKUP_DEBOBSMUX(i) (OMAP343X_CONTROL_GENERAL_WKUP + \
> 0x008 + (i))
No need for these, they are all defined already in mux34xx.h, and
available via mux.h.
Regards,
Tony
>From bafb6a3d19149a4344e9e927f036df5411b9819a Mon Sep 17 00:00:00 2001
From: Tony Lindgren <t...@atomide.com>
Date: Wed, 13 Jan 2010 10:27:17 -0800
Subject: [PATCH] omap: Add functions for dynamic remuxing of pins
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <t...@atomide.com>
diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c
index 459ef23..28722a7 100644
--- a/arch/arm/mach-omap2/mux.c
+++ b/arch/arm/mach-omap2/mux.c
@@ -51,7 +51,7 @@ struct omap_mux_entry {
static unsigned long mux_phys;
static void __iomem *mux_base;
-static inline u16 omap_mux_read(u16 reg)
+u16 omap_mux_read(u16 reg)
{
if (cpu_is_omap24xx())
return __raw_readb(mux_base + reg);
@@ -59,7 +59,7 @@ static inline u16 omap_mux_read(u16 reg)
return __raw_readw(mux_base + reg);
}
-static inline void omap_mux_write(u16 val, u16 reg)
+void omap_mux_write(u16 val, u16 reg)
{
if (cpu_is_omap24xx())
__raw_writeb(val, mux_base + reg);
@@ -67,6 +67,14 @@ static inline void omap_mux_write(u16 val, u16 reg)
__raw_writew(val, mux_base + reg);
}
+void omap_mux_write_array(struct omap_board_mux *board_mux)
+{
+ while (board_mux->reg_offset != OMAP_MUX_TERMINATOR) {
+ omap_mux_write(board_mux->value, board_mux->reg_offset);
+ board_mux++;
+ }
+}
+
#if defined(CONFIG_ARCH_OMAP24XX) && defined(CONFIG_OMAP_MUX)
static struct omap_mux_cfg arch_mux_cfg;
@@ -833,14 +841,6 @@ static void __init omap_mux_set_cmdline_signals(void)
kfree(options);
}
-static void __init omap_mux_set_board_signals(struct omap_board_mux *board_mux)
-{
- while (board_mux->reg_offset != OMAP_MUX_TERMINATOR) {
- omap_mux_write(board_mux->value, board_mux->reg_offset);
- board_mux++;
- }
-}
-
static int __init omap_mux_copy_names(struct omap_mux *src,
struct omap_mux *dst)
{
@@ -999,7 +999,7 @@ int __init omap_mux_init(u32 mux_pbase, u32 mux_size,
if (package_balls)
omap_mux_package_init_balls(package_balls, superset);
omap_mux_set_cmdline_signals();
- omap_mux_set_board_signals(board_mux);
+ omap_mux_write_array(board_mux);
#endif
omap_mux_init_list(superset);
diff --git a/arch/arm/mach-omap2/mux.h b/arch/arm/mach-omap2/mux.h
index d8b4d5a..f8c2e7a 100644
--- a/arch/arm/mach-omap2/mux.h
+++ b/arch/arm/mach-omap2/mux.h
@@ -147,6 +147,30 @@ u16 omap_mux_get_gpio(int gpio);
void omap_mux_set_gpio(u16 val, int gpio);
/**
+ * omap_mux_read() - read mux register
+ * @mux_offset: Offset of the mux register
+ *
+ */
+u16 omap_mux_read(u16 mux_offset);
+
+/**
+ * omap_mux_write() - write mux register
+ * @val: New mux register value
+ * @mux_offset: Offset of the mux register
+ *
+ * This should be only needed for dynamic remuxing of non-gpio signals.
+ */
+void omap_mux_write(u16 val, u16 mux_offset);
+
+/**
+ * omap_mux_write_array() - write an array of mux registers
+ * @board_mux: Array of mux registers terminated by MAP_MUX_TERMINATOR
+ *
+ * This should be only needed for dynamic remuxing of non-gpio signals.
+ */
+void omap_mux_write_array(struct omap_board_mux *board_mux);
+
+/**
* omap3_mux_init() - initialize mux system with board specific set
* @board_mux: Board specific mux table
* @flags: OMAP package type used for the board
