Thara Gopinath <[email protected]> writes:
> This patch converts the exisitng smartreflex library into a
> platform driver with device , driver registrations using hardware mods.
> As part of this Ntarget values are passed as platform data.
>
> Signed-off-by: Thara Gopinath <[email protected]>
>
> ---
> arch/arm/mach-omap2/Makefile | 2 +-
> arch/arm/mach-omap2/smartreflex.c | 325
> +++++++++++++------------------------
> arch/arm/mach-omap2/smartreflex.h | 26 +++
> arch/arm/mach-omap2/sr_device.c | 139 ++++++++++++++++
> 4 files changed, 278 insertions(+), 214 deletions(-)
> create mode 100644 arch/arm/mach-omap2/sr_device.c
>
> diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
> index ab47043..62accd2 100644
> --- a/arch/arm/mach-omap2/Makefile
> +++ b/arch/arm/mach-omap2/Makefile
> @@ -48,7 +48,7 @@ obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
> obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o
> obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o cpuidle34xx.o
> obj-$(CONFIG_PM_DEBUG) += pm-debug.o
> -obj-$(CONFIG_OMAP_SMARTREFLEX) += smartreflex.o
> +obj-$(CONFIG_OMAP_SMARTREFLEX) += sr_device.o smartreflex.o
>
> AFLAGS_sleep24xx.o :=-Wa,-march=armv6
> AFLAGS_sleep34xx.o :=-Wa,-march=armv7-a
> diff --git a/arch/arm/mach-omap2/smartreflex.c
> b/arch/arm/mach-omap2/smartreflex.c
> index dc8d6e1..b4e98e5 100644
> --- a/arch/arm/mach-omap2/smartreflex.c
> +++ b/arch/arm/mach-omap2/smartreflex.c
> @@ -3,6 +3,9 @@
> *
> * OMAP34XX SmartReflex Voltage Control
> *
> + * Copyright (C) 2010 Texas Instruments, Inc.
> + * Thara Gopinath <[email protected]>
> + *
> * Copyright (C) 2008 Nokia Corporation
> * Kalle Jokiniemi
> *
> @@ -14,7 +17,6 @@
> * published by the Free Software Foundation.
> */
>
> -
> #include <linux/kernel.h>
> #include <linux/init.h>
> #include <linux/interrupt.h>
> @@ -29,10 +31,11 @@
> #include <linux/list.h>
>
> #include <plat/omap34xx.h>
> -#include <plat/control.h>
> #include <plat/clock.h>
> #include <plat/opp.h>
> #include <plat/opp_twl_tps.h>
> +#include <plat/omap_hwmod.h>
> +#include <plat/omap_device.h>
>
> #include "prm.h"
> #include "smartreflex.h"
> @@ -41,45 +44,44 @@
> #define MAX_TRIES 100
>
> struct omap_sr {
> - int srid;
> - int is_sr_reset;
> - int is_autocomp_active;
> - struct clk *clk;
> - struct clk *vdd_opp_clk;
> - u32 clk_length;
> - u32 req_opp_no;
> - u32 opp1_nvalue, opp2_nvalue, opp3_nvalue, opp4_nvalue;
> - u32 opp5_nvalue;
> - u32 senp_mod, senn_mod;
> - void __iomem *srbase_addr;
I think you should leave the srbase_addr here and keep the register
access the way it is (using __raw_[read|write]*) My preference for
general drivers is to keep the omap_hwmod/omap_device usage in the
driver to a minimum. More on this below in comments on the _probe
function.
I would just rename it from 'srbase_addr' to 'base'.
> + int srid;
> + int is_sr_reset;
> + int is_autocomp_active;
> + struct clk *vdd_opp_clk;
> + u32 clk_length;
> + unsigned int irq;
> + struct platform_device *pdev;
> struct list_head node;
> };
>
> /* sr_list contains all the instances of smartreflex module */
> static LIST_HEAD(sr_list);
>
> -#define SR_REGADDR(offs) (sr->srbase_addr + offset)
> -
> static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32
> value)
> {
> - __raw_writel(value, SR_REGADDR(offset));
> + struct omap_device *odev = to_omap_device(sr->pdev);
> +
> + omap_hwmod_writel(value, odev->hwmods[0], offset);
> }
>
> static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32
> mask,
> u32 value)
> {
> + struct omap_device *odev = to_omap_device(sr->pdev);
> u32 reg_val;
>
> - reg_val = __raw_readl(SR_REGADDR(offset));
> + reg_val = omap_hwmod_readl(odev->hwmods[0], offset);
> reg_val &= ~mask;
> reg_val |= value;
>
> - __raw_writel(reg_val, SR_REGADDR(offset));
> + omap_hwmod_writel(reg_val, odev->hwmods[0], offset);
> }
>
> static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)
> {
> - return __raw_readl(SR_REGADDR(offset));
> + struct omap_device *odev = to_omap_device(sr->pdev);
> +
> + return omap_hwmod_readl(odev->hwmods[0], offset);
> }
>
> static struct omap_sr *_sr_lookup(int srid)
> @@ -98,71 +100,22 @@ static struct omap_sr *_sr_lookup(int srid)
>
> static int sr_clk_enable(struct omap_sr *sr)
> {
> - if (clk_enable(sr->clk) != 0) {
> - pr_err("Could not enable %s\n", sr->clk->name);
> - return -1;
> - }
> + struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;
>
> - /* set fclk- active , iclk- idle */
> - sr_modify_reg(sr, ERRCONFIG, SR_CLKACTIVITY_MASK,
> - SR_CLKACTIVITY_IOFF_FON);
> + if (pdata->device_enable)
> + pdata->device_enable(sr->pdev);
>
> return 0;
> }
>
> static void sr_clk_disable(struct omap_sr *sr)
> {
> - /* set fclk, iclk- idle */
> - sr_modify_reg(sr, ERRCONFIG, SR_CLKACTIVITY_MASK,
> - SR_CLKACTIVITY_IOFF_FOFF);
> -
> - clk_disable(sr->clk);
> - sr->is_sr_reset = 1;
> -}
> -
> -static struct omap_sr sr1 = {
> - .srid = SR1,
> - .is_sr_reset = 1,
> - .is_autocomp_active = 0,
> - .clk_length = 0,
> - .srbase_addr = OMAP2_L4_IO_ADDRESS(OMAP34XX_SR1_BASE),
> -};
> -
> -static struct omap_sr sr2 = {
> - .srid = SR2,
> - .is_sr_reset = 1,
> - .is_autocomp_active = 0,
> - .clk_length = 0,
> - .srbase_addr = OMAP2_L4_IO_ADDRESS(OMAP34XX_SR2_BASE),
> -};
> -
> -static void cal_reciprocal(u32 sensor, u32 *sengain, u32 *rnsen)
> -{
> - u32 gn, rn, mul;
> -
> - for (gn = 0; gn < GAIN_MAXLIMIT; gn++) {
> - mul = 1 << (gn + 8);
> - rn = mul / sensor;
> - if (rn < R_MAXLIMIT) {
> - *sengain = gn;
> - *rnsen = rn;
> - }
> - }
> -}
> -
> -static u32 cal_test_nvalue(u32 sennval, u32 senpval)
> -{
> - u32 senpgain, senngain;
> - u32 rnsenp, rnsenn;
> + struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;
>
> - /* Calculating the gain and reciprocal of the SenN and SenP values */
> - cal_reciprocal(senpval, &senpgain, &rnsenp);
> - cal_reciprocal(sennval, &senngain, &rnsenn);
> + if (pdata->device_idle)
> + pdata->device_idle(sr->pdev);
>
> - return (senpgain << NVALUERECIPROCAL_SENPGAIN_SHIFT) |
> - (senngain << NVALUERECIPROCAL_SENNGAIN_SHIFT) |
> - (rnsenp << NVALUERECIPROCAL_RNSENP_SHIFT) |
> - (rnsenn << NVALUERECIPROCAL_RNSENN_SHIFT);
> + sr->is_sr_reset = 1;
> }
>
> static u8 get_vdd1_opp(void)
> @@ -255,76 +208,6 @@ static void sr_set_clk_length(struct omap_sr *sr)
> }
> }
>
> -static void sr_set_efuse_nvalues(struct omap_sr *sr)
> -{
> - if (sr->srid == SR1) {
> - sr->senn_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
> - OMAP343X_SR1_SENNENABLE_MASK) >>
> - OMAP343X_SR1_SENNENABLE_SHIFT;
> - sr->senp_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
> - OMAP343X_SR1_SENPENABLE_MASK) >>
> - OMAP343X_SR1_SENPENABLE_SHIFT;
> -
> - sr->opp5_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP5_VDD1);
> - sr->opp4_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP4_VDD1);
> - sr->opp3_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP3_VDD1);
> - sr->opp2_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP2_VDD1);
> - sr->opp1_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP1_VDD1);
> - } else if (sr->srid == SR2) {
> - sr->senn_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
> - OMAP343X_SR2_SENNENABLE_MASK) >>
> - OMAP343X_SR2_SENNENABLE_SHIFT;
> -
> - sr->senp_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
> - OMAP343X_SR2_SENPENABLE_MASK) >>
> - OMAP343X_SR2_SENPENABLE_SHIFT;
> -
> - sr->opp3_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP3_VDD2);
> - sr->opp2_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP2_VDD2);
> - sr->opp1_nvalue = omap_ctrl_readl(
> - OMAP343X_CONTROL_FUSE_OPP1_VDD2);
> - }
> -}
> -
> -/* Hard coded nvalues for testing purposes, may cause device to hang! */
> -static void sr_set_testing_nvalues(struct omap_sr *sr)
> -{
> - if (sr->srid == SR1) {
> - sr->senp_mod = 0x03; /* SenN-M5 enabled */
> - sr->senn_mod = 0x03;
> -
> - /* calculate nvalues for each opp */
> - sr->opp5_nvalue = cal_test_nvalue(0xacd + 0x330, 0x848 + 0x330);
> - sr->opp4_nvalue = cal_test_nvalue(0x964 + 0x2a0, 0x727 + 0x2a0);
> - sr->opp3_nvalue = cal_test_nvalue(0x85b + 0x200, 0x655 + 0x200);
> - sr->opp2_nvalue = cal_test_nvalue(0x506 + 0x1a0, 0x3be + 0x1a0);
> - sr->opp1_nvalue = cal_test_nvalue(0x373 + 0x100, 0x28c + 0x100);
> - } else if (sr->srid == SR2) {
> - sr->senp_mod = 0x03;
> - sr->senn_mod = 0x03;
> -
> - sr->opp3_nvalue = cal_test_nvalue(0x76f + 0x200, 0x579 + 0x200);
> - sr->opp2_nvalue = cal_test_nvalue(0x4f5 + 0x1c0, 0x390 + 0x1c0);
> - sr->opp1_nvalue = cal_test_nvalue(0x359, 0x25d);
> - }
> -
> -}
> -
> -static void sr_set_nvalues(struct omap_sr *sr)
> -{
> - if (SR_TESTING_NVALUES)
> - sr_set_testing_nvalues(sr);
> - else
> - sr_set_efuse_nvalues(sr);
> -}
> -
> static void sr_configure_vp(int srid)
> {
> u32 vpconfig;
> @@ -438,12 +321,13 @@ static void sr_configure(struct omap_sr *sr)
> {
> u32 sr_config;
> u32 senp_en , senn_en;
> + struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;
>
> if (sr->clk_length == 0)
> sr_set_clk_length(sr);
>
> - senp_en = sr->senp_mod;
> - senn_en = sr->senn_mod;
> + senp_en = pdata->senp_mod;
> + senn_en = pdata->senn_mod;
> if (sr->srid == SR1) {
> sr_config = SR1_SRCONFIG_ACCUMDATA |
> (sr->clk_length << SRCONFIG_SRCLKLENGTH_SHIFT) |
> @@ -571,57 +455,28 @@ static int sr_enable(struct omap_sr *sr, u32
> target_opp_no)
> {
> u32 nvalue_reciprocal, v;
> struct omap_opp *opp;
> + struct omap_smartreflex_data *pdata = sr->pdev->dev.platform_data;
> int uvdc;
> char vsel;
>
> - sr->req_opp_no = target_opp_no;
> -
> if (sr->srid == SR1) {
> - switch (target_opp_no) {
> - case 5:
> - nvalue_reciprocal = sr->opp5_nvalue;
> - break;
> - case 4:
> - nvalue_reciprocal = sr->opp4_nvalue;
> - break;
> - case 3:
> - nvalue_reciprocal = sr->opp3_nvalue;
> - break;
> - case 2:
> - nvalue_reciprocal = sr->opp2_nvalue;
> - break;
> - case 1:
> - nvalue_reciprocal = sr->opp1_nvalue;
> - break;
> - default:
> - nvalue_reciprocal = sr->opp3_nvalue;
> - break;
> - }
> -
> opp = opp_find_by_opp_id(OPP_MPU, target_opp_no);
> if (!opp)
> return false;
> } else {
> - switch (target_opp_no) {
> - case 3:
> - nvalue_reciprocal = sr->opp3_nvalue;
> - break;
> - case 2:
> - nvalue_reciprocal = sr->opp2_nvalue;
> - break;
> - case 1:
> - nvalue_reciprocal = sr->opp1_nvalue;
> - break;
> - default:
> - nvalue_reciprocal = sr->opp3_nvalue;
> - break;
> - }
> -
> opp = opp_find_by_opp_id(OPP_L3, target_opp_no);
> if (!opp)
> return false;
> }
>
> + if (!pdata->sr_nvalue) {
> + pr_notice("N target values does not exist for SR%d\n",
> + sr->srid);
> + return false;
> + }
> +
> + nvalue_reciprocal = pdata->sr_nvalue[target_opp_no - 1];
> +
> if (nvalue_reciprocal == 0) {
> pr_notice("OPP%d doesn't support SmartReflex\n",
> target_opp_no);
> @@ -1033,49 +888,93 @@ static struct kobj_attribute sr_vdd2_autocomp = {
> .store = omap_sr_vdd2_autocomp_store,
> };
>
> +static int __devinit omap_smartreflex_probe(struct platform_device *pdev)
> +{
> + struct omap_sr *sr_info = kzalloc(sizeof(struct omap_sr), GFP_KERNEL);
> + struct omap_device *odev = to_omap_device(pdev);
> + int ret = 0;
> +
> + if (WARN_ON(!sr_info))
> + return -ENOMEM;
> + sr_info->pdev = pdev;
> + sr_info->srid = pdev->id + 1;
> + sr_info->is_sr_reset = 1,
> + sr_info->is_autocomp_active = 0;
> + sr_info->clk_length = 0;
> + if (odev->hwmods[0]->mpu_irqs)
> + sr_info->irq = odev->hwmods[0]->mpu_irqs[0].irq;
You should use platform_get_resource(..., IORESOURCE_IRQ) here instead
of accessing the hwmod. (or better, platform_get_irq().)
Remember that omap_device_build() builds a platform_device as well
with all the resources (base addresses, IRQs, DMA channels) so the
standard platform_get_resource() calls should be used to get all
those.
And, for the base address, use
sr_info->base = platform_get_resource(pdev, IORESOURCE_MEM);
Ideally, as generic driver here should have no (or minimal) knowledge of
omap_device/omap_hwmod internals.
> + sr_set_clk_length(sr_info);
> +
> + if (sr_info->srid == SR1) {
> + sr_info->vdd_opp_clk = clk_get(NULL, "dpll1_ck");
> + ret = sysfs_create_file(power_kobj, &sr_vdd1_autocomp.attr);
> + if (ret)
> + pr_err("sysfs_create_file failed: %d\n", ret);
> + } else {
> + sr_info->vdd_opp_clk = clk_get(NULL, "l3_ick");
> + ret = sysfs_create_file(power_kobj, &sr_vdd2_autocomp.attr);
> + if (ret)
> + pr_err("sysfs_create_file failed: %d\n", ret);
> + }
> +
> + /* Call the VPConfig */
> + sr_configure_vp(sr_info->srid);
> + list_add(&sr_info->node, &sr_list);
> + pr_info("SmartReflex driver initialized\n");
> +
> + return ret;
> +}
> +
> +static int __devexit omap_smartreflex_remove(struct platform_device *pdev)
> +{
> + struct omap_sr *sr_info = _sr_lookup(pdev->id + 1);
>
> + /* Disable Autocompensation if enabled before removing the module */
> + if (sr_info->is_autocomp_active == 1)
> + sr_stop_vddautocomap(sr_info->srid);
> + list_del(&sr_info->node);
> + kfree(sr_info);
>
> -static int __init omap3_sr_init(void)
> + return 0;
> +}
> +
> +static struct platform_driver smartreflex_driver = {
> + .probe = omap_smartreflex_probe,
minor nit... since you're using platform_device_probe(), you don't
need a .probe function here, and you can make omap_smartreflex_probe()
__init.
> + .remove = omap_smartreflex_remove,
> + .driver = {
> + .name = "smartreflex",
> + },
> +};
> +
> +static int __init sr_init(void)
> {
> int ret = 0;
> u8 RdReg;
>
> + /* TODO: Find an appropriate place for this */
> /* Enable SR on T2 */
> ret = twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &RdReg,
> R_DCDC_GLOBAL_CFG);
> -
> RdReg |= DCDC_GLOBAL_CFG_ENABLE_SRFLX;
> ret |= twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, RdReg,
> R_DCDC_GLOBAL_CFG);
> - if (cpu_is_omap34xx()) {
> - sr1.clk = clk_get(NULL, "sr1_fck");
> - sr2.clk = clk_get(NULL, "sr2_fck");
> - }
> - sr1.vdd_opp_clk = clk_get(NULL, "dpll1_ck");
> - sr2.vdd_opp_clk = clk_get(NULL, "l3_ick");
> - sr_set_clk_length(&sr1);
> - sr_set_clk_length(&sr2);
> -
> - /* Call the VPConfig, VCConfig, set N Values. */
> - sr_set_nvalues(&sr1);
> - sr_configure_vp(SR1);
> -
> - sr_set_nvalues(&sr2);
> - sr_configure_vp(SR2);
> -
> - pr_info("SmartReflex driver initialized\n");
>
> - ret = sysfs_create_file(power_kobj, &sr_vdd1_autocomp.attr);
> - if (ret)
> - pr_err("sysfs_create_file failed: %d\n", ret);
> + ret = platform_driver_probe(&smartreflex_driver,
> + omap_smartreflex_probe);
>
> - ret = sysfs_create_file(power_kobj, &sr_vdd2_autocomp.attr);
> if (ret)
> - pr_err("sysfs_create_file failed: %d\n", ret);
> - list_add(&sr1.node, &sr_list);
> - list_add(&sr2.node, &sr_list);
> -
> + pr_err("platform driver register failed for smartreflex");
> return 0;
> }
>
> -late_initcall(omap3_sr_init);
> +void __exit sr_exit(void)
> +{
> + platform_driver_unregister(&smartreflex_driver);
> +}
> +late_initcall(sr_init);
> +module_exit(sr_exit);
> +
> +MODULE_DESCRIPTION("OMAP SMARTREFLEX DRIVER");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:" DRIVER_NAME);
> +MODULE_AUTHOR("Texas Instruments Inc");
> diff --git a/arch/arm/mach-omap2/smartreflex.h
> b/arch/arm/mach-omap2/smartreflex.h
> index d239eb2..5eb8846 100644
> --- a/arch/arm/mach-omap2/smartreflex.h
> +++ b/arch/arm/mach-omap2/smartreflex.h
> @@ -14,6 +14,8 @@
> * published by the Free Software Foundation.
> */
>
> +#include <linux/platform_device.h>
> +
> #define PHY_TO_OFF_PM_MASTER(p) (p - 0x36)
> #define PHY_TO_OFF_PM_RECIEVER(p) (p - 0x5b)
> #define PHY_TO_OFF_PM_INT(p) (p - 0x2e)
> @@ -276,6 +278,30 @@ struct omap_smartreflex_dev_data {
> * do anything.
> */
> #ifdef CONFIG_OMAP_SMARTREFLEX
> +/**
> + * omap_smartreflex_data - Smartreflex platform data
> + *
> + * @senp_mod : SENPENABLE value for the sr
> + * @senn_mod : SENNENABLE value for sr
> + * @sr_nvalue : array of n target values for sr
> + * @enable_on_init : whether this sr module needs to enabled at
> + * boot up or not
> + * @device_enable : fn pointer to be populated with omap_device
> + * enable API
> + * @device_shutdown : fn pointer to be populated with omap_device
> + * shutdown API
> + * @device_idle : fn pointer to be pouplated with omap_device
> idle API
You can drop the comments about omap_device API. These are intended to
be generic pointers. The device part is free to fill those out
> + */
> +struct omap_smartreflex_data {
Also, how about a rename to omap_sr_data;
> + u32 senp_mod;
> + u32 senn_mod;
> + u32 *sr_nvalue;
> + bool enable_on_init;
> + int (*device_enable)(struct platform_device *pdev);
> + int (*device_shutdown)(struct platform_device *pdev);
> + int (*device_idle)(struct platform_device *pdev);
> +};
> +
> void enable_smartreflex(int srid);
> void disable_smartreflex(int srid);
> int sr_voltagescale_vcbypass(u32 t_opp, u32 c_opp, u8 t_vsel, u8 c_vsel);
> diff --git a/arch/arm/mach-omap2/sr_device.c b/arch/arm/mach-omap2/sr_device.c
> new file mode 100644
> index 0000000..a9c1ef0
> --- /dev/null
> +++ b/arch/arm/mach-omap2/sr_device.c
> @@ -0,0 +1,139 @@
> +/*
> + * linux/arch/arm/mach-omap2/sr_device.c
Please drop the filename from the header.
> + * OMAP3/OMAP4 smartreflex device file
> + *
> + * Author: Thara Gopinath <[email protected]>
> + *
> + * Based originally on code from smartreflex.c
> + * Copyright (C) 2010 Texas Instruments, Inc.
> + * Thara Gopinath <[email protected]>
> + *
> + * Copyright (C) 2008 Nokia Corporation
> + * Kalle Jokiniemi
> + *
> + * Copyright (C) 2007 Texas Instruments, Inc.
> + * Lesly A M <[email protected]>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/err.h>
> +
> +#include <plat/control.h>
> +#include <plat/omap_hwmod.h>
> +#include <plat/omap_device.h>
> +#include <plat/opp.h>
> +
> +#include "smartreflex.h"
> +
> +#define MAX_HWMOD_NAME_LEN 16
> +
> +struct omap_device_pm_latency omap_sr_latency[] = {
> + {
> + .deactivate_func = omap_device_idle_hwmods,
> + .activate_func = omap_device_enable_hwmods,
> + .flags = OMAP_DEVICE_LATENCY_AUTO_ADJUST
> + },
> +};
> +
> +/* Read EFUSE values from control registers for OMAP3430 */
> +static void __init sr_read_efuse(
> + struct omap_smartreflex_dev_data *dev_data,
> + struct omap_smartreflex_data *sr_data)
> +{
> + int i;
> +
> + if (WARN_ON(!dev_data || !dev_data->volts_supported ||
> + !dev_data->efuse_sr_control ||
> + !dev_data->efuse_nvalues_offs))
> + return;
> +
> + sr_data->sr_nvalue = kzalloc(sizeof(sr_data->sr_nvalue) *
> + dev_data->volts_supported , GFP_KERNEL);
> + sr_data->senn_mod = (omap_ctrl_readl(dev_data->efuse_sr_control) &
> + (0x3 << dev_data->sennenable_shift) >>
> + dev_data->sennenable_shift);
> + sr_data->senp_mod = (omap_ctrl_readl(dev_data->efuse_sr_control) &
> + (0x3 << dev_data->senpenable_shift) >>
> + dev_data->senpenable_shift);
> + for (i = 0; i < dev_data->volts_supported; i++)
> + sr_data->sr_nvalue[i] = omap_ctrl_readl(
> + dev_data->efuse_nvalues_offs[i]);
> +}
> +
> +/*
> + * Hard coded nvalues for testing purposes for OMAP3430,
> + * may cause device to hang!
> + */
> +static void __init sr_set_testing_nvalues(
> + struct omap_smartreflex_dev_data *dev_data,
> + struct omap_smartreflex_data *sr_data)
> +{
> + int i;
> +
> + if (WARN_ON(!dev_data || !dev_data->volts_supported ||
> + !dev_data->test_nvalues))
> + return;
> +
> + sr_data->sr_nvalue = kzalloc(sizeof(sr_data->sr_nvalue) *
> + dev_data->volts_supported , GFP_KERNEL);
> + sr_data->senn_mod = dev_data->test_sennenable;
> + sr_data->senp_mod = dev_data->test_senpenable;
> + for (i = 0; i < dev_data->volts_supported; i++)
> + sr_data->sr_nvalue[i] = dev_data->test_nvalues[i];
> +}
> +
> +static void __init sr_set_nvalues(struct omap_smartreflex_dev_data *dev_data,
> + struct omap_smartreflex_data *sr_data)
> +{
> + if (cpu_is_omap34xx()) {
Why this check? Looks like the called functions already check for
valid data. Also, I don't see this changed/updated in the 3630 patches.
> + if (SR_TESTING_NVALUES)
> + sr_set_testing_nvalues(dev_data, sr_data);
> + else
> + sr_read_efuse(dev_data, sr_data);
> + }
> +}
> +
> +static int __init omap_devinit_smartreflex(void)
> +{
> + int i = 0;
> + char *name = "smartreflex";
> +
> + do {
> + struct omap_smartreflex_data *sr_data;
> + struct omap_smartreflex_dev_data *sr_dev_data;
> + struct omap_device *od;
> + struct omap_hwmod *oh;
> + char oh_name[MAX_HWMOD_NAME_LEN + 1];
> +
> + snprintf(oh_name, MAX_HWMOD_NAME_LEN, "sr%d_hwmod", i + 1);
> + oh = omap_hwmod_lookup(oh_name);
Should be using the hwmod_class to iterate: omap_hwmod_for_each_by_class()
> + if (!oh)
> + break;
> +
> + sr_data = kzalloc(sizeof(struct omap_smartreflex_data),
> + GFP_KERNEL);
> + sr_dev_data = (struct omap_smartreflex_dev_data *)oh->dev_attr;
> + if (WARN_ON(!sr_data))
> + return -ENOMEM;
> +
> + sr_data->enable_on_init = false;
> + sr_data->device_enable = omap_device_enable;
> + sr_data->device_shutdown = omap_device_shutdown;
> + sr_data->device_idle = omap_device_idle;
> + sr_set_nvalues(sr_dev_data, sr_data);
> +
> + od = omap_device_build(name, i, oh, sr_data, sizeof(*sr_data),
> + omap_sr_latency,
> + ARRAY_SIZE(omap_sr_latency), 0);
> + WARN(IS_ERR(od), "Could not build omap_device for %s: %s.\n",
> + name, oh->name);
> + i++;
> + } while (1);
> +
> + return 0;
> +}
> +arch_initcall(omap_devinit_smartreflex);
Kevin
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
