Hello, > -----Original Message----- > From: Heikki Krogerus [mailto:[email protected]] > Sent: 28. maaliskuuta 2011 12:13 > To: Jokiniemi Kalle (Nokia-MS/Tampere) > Cc: [email protected]; [email protected]; [email protected]; > [email protected]; [email protected] > Subject: Re: [PATCH v2 1/2] isp1704_charger: allow board specific powering > routine > > Hi, > > Add Anton Vorontsov <[email protected]> to your v3. This will > need ack from him, or this needs to go to him. In this case I guess we > are only dealing with RX51 stuff, so maybe this should go to Tony.
Thanks, I'll add Anton to cc. > > On Mon, Mar 28, 2011 at 09:51:38AM +0300, Kalle Jokiniemi wrote: > > The ISP1704/1707 chip can be put to full power down > > state by asserting the CHIP_SEL line. This patch enables > > platform or board specific hooks to put the device into > > power down mode in case not needed. > > > > These patches are preparatio for enabling this powering > > routine in n900 (rx-51) devices. > > > > Thanks to Heikki Krogerus for helping out with the patch. > > > > Signed-off-by: Kalle Jokiniemi <[email protected]> > > Cc: Heikki Krogerus <[email protected]> > > --- > > drivers/power/isp1704_charger.c | 26 ++++++++++++++++++++++++++ > > include/linux/power/isp1704_charger.h | 29 > +++++++++++++++++++++++++++++ > > 2 files changed, 55 insertions(+), 0 deletions(-) > > create mode 100644 include/linux/power/isp1704_charger.h > > > > diff --git a/drivers/power/isp1704_charger.c > b/drivers/power/isp1704_charger.c > > index 2ad9b14..c796b9f 100644 > > --- a/drivers/power/isp1704_charger.c > > +++ b/drivers/power/isp1704_charger.c > > @@ -33,6 +33,7 @@ > > #include <linux/usb/ulpi.h> > > #include <linux/usb/ch9.h> > > #include <linux/usb/gadget.h> > > +#include <linux/power/isp1704_charger.h> > > > > /* Vendor specific Power Control register */ > > #define ISP1704_PWR_CTRL 0x3d > > @@ -63,6 +64,7 @@ struct isp1704_charger { > > char model[8]; > > unsigned present:1; > > unsigned online:1; > > + unsigned init_done; > > Do we need this? Good point. I needed this for 2.6.37 meego kernel, because it calls otg_get_last_event in middle of the probing, which causes the isp1704_charger_work to be run with USB_EVENT_NONE, which then caused the power to be shut down from the isp during probe. But it seems the get_last_notifier is not called in upstream code, So I probably can drop that init_done variable. > > > unsigned current_max; > > > > /* temp storage variables */ > > @@ -71,6 +73,18 @@ struct isp1704_charger { > > }; > > > > /* > > + * Disable/enable the power from the isp1704 if a function for it > > + * has been provided with platform data. > > + */ > > +static void isp1704_charger_set_power(struct isp1704_charger *isp, bool > on) > > +{ > > + struct isp1704_charger_data *board = isp->dev->platform_data; > > + > > + if (board->set_power) > > + board->set_power(on); > > +} > > + > > +/* > > * Determine is the charging port DCP (dedicated charger) or CDP (Host/HUB > > * chargers). > > * > > @@ -222,6 +236,9 @@ static void isp1704_charger_work(struct work_struct > *data) > > > > mutex_lock(&lock); > > > > + if (event != USB_EVENT_NONE) > > + isp1704_charger_set_power(isp, 1); > > + > > switch (event) { > > case USB_EVENT_VBUS: > > isp->online = true; > > @@ -269,6 +286,9 @@ static void isp1704_charger_work(struct work_struct > *data) > > */ > > if (isp->otg->gadget) > > usb_gadget_disconnect(isp->otg->gadget); > > + /* If we're initialized, we can power down the isp */ > > + if (isp->init_done) > > + isp1704_charger_set_power(isp, 0); > > break; > > case USB_EVENT_ENUMERATED: > > if (isp->present) > > @@ -394,6 +414,8 @@ static int __devinit isp1704_charger_probe(struct > platform_device *pdev) > > isp->dev = &pdev->dev; > > platform_set_drvdata(pdev, isp); > > > > + isp1704_charger_set_power(isp, 1); > > + > > ret = isp1704_test_ulpi(isp); > > if (ret < 0) > > goto fail1; > > @@ -437,8 +459,11 @@ static int __devinit isp1704_charger_probe(struct > platform_device *pdev) > > if ((ret & ULPI_INT_VBUS_VALID) && !isp->otg->default_a) { > > isp->event = USB_EVENT_VBUS; > > schedule_work(&isp->work); > > + } else { > > + isp1704_charger_set_power(isp, 0); > > } > > I think the transceiver can be powered down even if we just scheduled > the work. This will basically cause hw reset on the transceiver which > is only a good thing IMO. Drop the else condition. Ok, I'll test that out and include it if it works w/o problems. Thanks for the excellent comments. - Kalle > > > + isp->init_done = 1; > > return 0; > > fail2: > > power_supply_unregister(&isp->psy); > > @@ -459,6 +484,7 @@ static int __devexit isp1704_charger_remove(struct > platform_device *pdev) > > otg_unregister_notifier(isp->otg, &isp->nb); > > power_supply_unregister(&isp->psy); > > otg_put_transceiver(isp->otg); > > + isp1704_charger_set_power(isp, 0); > > kfree(isp); > > > > return 0; > > -- > heikki -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
