On Thu, Aug 25, 2011 at 9:49 PM, Guenter Roeck
<guenter.ro...@ericsson.com> wrote:
> On Thu, 2011-08-25 at 12:04 -0400, J, KEERTHY wrote:
>> On Thu, Aug 25, 2011 at 7:36 PM, Guenter Roeck
>> <guenter.ro...@ericsson.com> wrote:
>> > On Thu, Aug 25, 2011 at 06:30:07AM -0400, J, KEERTHY wrote:
>> >> On Wed, Aug 24, 2011 at 10:46 PM, Guenter Roeck
>> >> <guenter.ro...@ericsson.com> wrote:
>> >> > On Wed, Aug 24, 2011 at 10:37:12AM -0400, Keerthy wrote:
>> >> >> On chip temperature sensor driver. The driver monitors the temperature
>> >> >> of
>> >> >> the MPU subsystem of the OMAP4. It sends notifications to the user
>> >> >> space if
>> >> >> the temperature crosses user defined thresholds via kobject_uevent
>> >> >> interface.
>> >> >> The user is allowed to configure the temperature thresholds vis sysfs
>> >> >> nodes
>> >> >> exposed using hwmon interface.
>> >> >>
>> >> >> Signed-off-by: Keerthy <j-keer...@ti.com>
>> >> >> Cc: Jean Delvare <kh...@linux-fr.org>
>> >> >> Cc: Guenter Roeck <guenter.ro...@ericsson.com>
>> >> >> Cc: lm-sens...@lm-sensors.org
>> >> >
>> >> > Partial review only. Too many concerns, and after a while I tend to
>> >> > loose track.
>> >> >
>> >> >> ---
>> >> >> Documentation/hwmon/omap_temp_sensor | 27 +
>> >> >> drivers/hwmon/Kconfig | 11 +
>> >> >> drivers/hwmon/Makefile | 1 +
>> >> >> drivers/hwmon/omap_temp_sensor.c | 933
>> >> >> ++++++++++++++++++++++++++++++++++
>> >> >> 4 files changed, 972 insertions(+), 0 deletions(-)
>> >> >> create mode 100644 Documentation/hwmon/omap_temp_sensor
>> >> >> create mode 100644 drivers/hwmon/omap_temp_sensor.c
>> >> >>
>> >
>> > [ ... ]
>> >
>> >> >> +/* Sysfs hook functions */
>> >> >> +
>> >> >> +static ssize_t show_temp_max(struct device *dev,
>> >> >> + struct device_attribute *devattr, char *buf)
>> >> >> +{
>> >> >> + struct omap_temp_sensor *temp_sensor = dev_get_drvdata(dev);
>> >> >> + int temp;
>> >> >> +
>> >> >> + temp = omap_temp_sensor_readl(temp_sensor,
>> >> >> + temp_sensor->registers->bgap_threshold);
>> >> >> + temp = (temp & temp_sensor->registers->threshold_thot_mask)
>> >> >> + >>
>> >> >> __ffs(temp_sensor->registers->threshold_thot_mask);
>> >> >> +
>> >> >> + if (temp < OMAP_ADC_START_VALUE || temp > OMAP_ADC_END_VALUE) {
>> >> >> + dev_err(dev, "invalid value\n");
>> >> >> + return -EDOM;
>> >> >
>> >> > Please don't use EDOM, and drop the error message.
>> >>
>> >> The temperature is out of range. Should i use EIO?
>> >>
>> > It is out of range, but not due to a math error, but due to a bad reading
>> > from the chip
>> > or due to a chip failure. EIO is ok.
>>
>> Ok
>>
>> >
>> >> >
>> >> >> + }
>> >> >> +
>> >> >> + temp = adc_to_temp_conversion(temp);
>> >> >> +
>> >> >> + return snprintf(buf, 16, "%d\n", temp);
>> >> >> +}
>> >> >> +
>> >> >> +static ssize_t set_temp_max(struct device *dev,
>> >> >> + struct device_attribute *devattr,
>> >> >> + const char *buf, size_t count)
>> >> >> +{
>> >> >> + struct omap_temp_sensor *temp_sensor = dev_get_drvdata(dev);
>> >> >> + long val;
>> >> >> + u32 reg_val, t_cold, t_hot, temp;
>> >> >> +
>> >> >> + if (strict_strtol(buf, 10, &val)) {
>> >> >> + count = -EINVAL;
>> >> >> + goto out;
>> >> >
>> >> > This will try to release the not-acquired lock.
>> >>
>> >> I will correct this.
>> >>
>> >> >
>> >> >> + }
>> >> >> +
>> >> >> + t_hot = temp_to_adc_conversion(val);
>> >> >
>> >> > Bad error return check. Negative on error. Should be
>> >> > if (t_hot < 0)
>> >> > return t_hot;
>> >>
>> >> Ok.
>> >>
>> >> >
>> >> >> + if ((t_hot < OMAP_ADC_START_VALUE || t_hot >
>> >> >> OMAP_ADC_END_VALUE)) {
>> >> >
>> >> > Unnecessary (( ))
>> >>
>> >> This check is unnecessary with the negative check. I will remove.
>> >>
>> >> >
>> >> >> + count = -EINVAL;
>> >> >> + goto out;
>> >> >
>> >> > This will try to release the not-acquired lock.
>> >>
>> >> I will correct this.
>> >>
>> >> >
>> >> >> + }
>> >> >> +
>> >> >> + mutex_lock(&temp_sensor->sensor_mutex);
>> >> >> + /* obtain the T cold value */
>> >> >> + t_cold = omap_temp_sensor_readl(temp_sensor,
>> >> >> + temp_sensor->registers->bgap_threshold);
>> >> >> + t_cold = (t_cold &
>> >> >> temp_sensor->registers->threshold_tcold_mask) >>
>> >> >> +
>> >> >> __ffs(temp_sensor->registers->threshold_tcold_mask);
>> >> >> +
>> >> >> + if (t_hot < t_cold) {
>> >> >> + count = -EINVAL;
>> >> >> + goto out;
>> >> >
>> >> > Context specific limitations like this one are not a good idea, since
>> >> > it assumes an order of changing max
>> >> > and max_hysteresis which is not necessarily guaranteed by the
>> >> > application making the change, nor is a
>> >> > change order order well defined or even possible. Applications should
>> >> > not have to bother about this.
>> >>
>> >> The hardware behavior is like this. As long as the temperature is below
>> >> t_hot no interrupts are fired. Once the temperature increases above
>> >> t_hot we get an
>> >> interrupt. In order to avoid repeated interrupts we mask the t_hot
>> >> interrupt
>> >> in the interrupt handler and enable the t_cold interrupts. So we get a
>> >> t_cold
>> >> interrupt only when the temperature drops below the t_cold value. Hence
>> >> setting the t_cold higher than t_hot will mess up the state machine.
>> >>
>> >> t_hot value should be greater than t_cold value.
>> >>
>> > One option would be to update t_cold (max_hyst) automatically in that case.
>>
>> updating the t_cold without application's knowledge?
>>
> Why not ? Other drivers do the same. Happens all the time. Better than
> returning an error and leaving the application wondering what is wrong.
>
>> >
>> > Problem here is that you expect the aplication to know, depending on the
>> > current
>> > values of (max, max_hyst), how to update both limits in order. That is not
>> > a reasonable
>> > expectation.
>>
>> The thermal application which is configuring the thresholds must be
>> intelligent enough to configure the thresholds in the right order.
>> Configuring
>> the thresholds wrongly and missing the interrupt may even result in burning
>> the chip.
>>
>
> Applications are generic, and _can not_ be expected to know chip
> specific requirements such as order of initialization. What is needed
> for your chip may be completely different for another chip, so you have
> to make sure that _your driver_ prevents critical situations from
> happening. You can not blame applications for not knowing the oddities
> of your chips.
>
>> >
>> >> >
>> >> >> + }
>> >> >> +
>> >> >> + /* write the new t_hot value */
>> >> >> + reg_val = omap_temp_sensor_readl(temp_sensor,
>> >> >> + temp_sensor->registers->bgap_threshold);
>> >> >> + reg_val &= ~temp_sensor->registers->threshold_thot_mask;
>> >> >> + reg_val |= (t_hot <<
>> >> >> +
>> >> >> __ffs(temp_sensor->registers->threshold_thot_mask));
>> >> >> + omap_temp_sensor_writel(temp_sensor, reg_val,
>> >> >> + temp_sensor->registers->bgap_threshold);
>> >> >> +
>> >> >> + /* Read the current temperature */
>> >> >> + temp = omap_temp_sensor_readl(temp_sensor,
>> >> >> + temp_sensor->registers->temp_sensor_ctrl);
>> >> >> + temp &= temp_sensor->registers->bgap_dtemp_mask;
>> >> >> +
>> >> >> + /*
>> >> >> + * If user sets the HIGH threshold(t_hot) greater than the
>> >> >> current
>> >> >> + * temperature(temp) unmask the HOT interrupts
>> >> >> + */
>> >> >> + if (t_hot > temp) {
>> >> >> + reg_val = omap_temp_sensor_readl(temp_sensor,
>> >> >> +
>> >> >> temp_sensor->registers->bgap_mask_ctrl);
>> >> >> + reg_val &= ~temp_sensor->registers->mask_cold_mask;
>> >> >> + reg_val |= temp_sensor->registers->mask_hot_mask;
>> >> >> + omap_temp_sensor_writel(temp_sensor, reg_val,
>> >> >> +
>> >> >> temp_sensor->registers->bgap_mask_ctrl);
>> >> >> + }
>> >> >> +
>> >> >> + /*
>> >> >> + * If current temperature is in-between the hot and cold
>> >> >> thresholds,
>> >> >> + * Enable both masks.
>> >> >> + */
>> >> >> + if (temp > t_cold && temp < t_hot) {
>> >> >> + reg_val = omap_temp_sensor_readl(temp_sensor,
>> >> >> +
>> >> >> temp_sensor->registers->bgap_mask_ctrl);
>> >> >> + reg_val |= temp_sensor->registers->mask_cold_mask;
>> >> >> + reg_val |= temp_sensor->registers->mask_hot_mask;
>> >> >> + omap_temp_sensor_writel(temp_sensor, reg_val,
>> >> >> + OMAP4460_BGAP_CTRL_OFFSET);
>> >> >
>> >> > Why use OMAP4460_BGAP_CTRL_OFFSET here but bgap_mask_ctrl elsewhere ?
>> >>
>> >> Ok. I will change this.
>> >>
>> >> >
>> >> >> + }
>> >> >> + /*
>> >> >> + * else no need to do anything since HW will immediately
>> >> >> compare
>> >> >> + * the new threshold and generate interrupt accordingly
>> >> >> + */
>> >> >> +out:
>> >> >> + mutex_unlock(&temp_sensor->sensor_mutex);
>> >> >> +
>> >> >> + return count;
>> >> >> +}
>> >> >> +
>> >> >> +static ssize_t show_temp_max_hyst(struct device *dev,
>> >> >> + struct device_attribute *devattr, char *buf)
>> >> >> +{
>> >> >> + struct omap_temp_sensor *temp_sensor = dev_get_drvdata(dev);
>> >> >> + u32 temp;
>> >> >> +
>> >> >> + mutex_lock(&temp_sensor->sensor_mutex);
>> >> >
>> >> > This lock would only make sense if threshold_tcold_mask can change, and
>> >> > if that change
>> >> > would be protected by the mutex. I don't see that to be the case, thus
>> >> > the lock is unnecessary.
>> >> > Besides, the code in show_temp_max() is almost the same and does not
>> >> > use the lock.
>> >>
>> >> The masks are getting changed in show_temp_max() show_temp_max_hyst() and
>> >> the
>> >> ISR function. It is better to protect with mutex. I will add that in
>> >> required places.
>> >>
>> > Reeally ? I seem to be blind. I searched for threshold_tcold_mask in the
>> > patch but
>> > did not see where it is changed. Can you point me to the code ?
>>
>> I misread it. Yes threshold_tcold_mask is used only in show_temp_max_hyst(),
>> set_temp_max(), set_temp_max_hyst() functions. It is set only in the
>> set_temp_max_hyst()
>> function.
>>
> I am still lost. Where exactly ? I don't see it being changed in
> set_temp_max_hyst() either. Outside initialization code, I only see
> writes to
> bgap_threshold
bgap_threshold is the register and "threshold_tcold_mask" is a bit field
in that register which is written in the set_temp_max_hyst() function to
configure temp_max_hyst.
Similarly "threshold_thot_mask" is a bit field in the bgap_threshold
register which is written in the set_temp_max() function to configure
temp_max.
> bgap_counter
> bgap_mask_ctrl
> but not to any of the masks.
>
> Thanks,
> Guenter
>
>
>
--
Regards and Thanks,
Keerthy
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
