Hello all,

I've got an old PE 1950 with a PERC5/i RAID controller joining (2) 250 GB ATA HDDs runner RHEL 5.3 (yes, this is slated to retire shortly). Log entries below.

How do I tell which of the two drives is causing this error? What is the best procedure to remove/replace the drive once identified? I have replacement drives but I don't want to pull the wrong one.

Your guidance would be very much appreciated.

Thank you,
Scott



======================


[root@server log]# df -h
Filesystem            Size  Used Avail Use% Mounted on
/dev/sda1              30G  3.5G   25G  13% /
tmpfs                 3.0G     0  3.0G   0% /dev/shm
/dev/sda2             194G  135G   50G  74% /opt


*/var/log/messages*

Mar 30 12:06:14 server kernel: hda: status error: status=0x50 { DriveReady SeekComplete }
Mar 30 12:06:14 server kernel: ide: failed opcode was: unknown
Mar 30 12:38:05 server kernel: hda: status error: status=0x50 { DriveReady SeekComplete }
Mar 30 12:38:05 server kernel: ide: failed opcode was: unknown
Mar 31 10:42:35 server kernel: hda: status error: status=0x50 { DriveReady SeekComplete }
Mar 31 10:42:35 server kernel: ide: failed opcode was: unknown


*/var/log/dmesg*

SCSI subsystem initialized
usb 1-5: new high speed USB device using ehci_hcd and address 3
megasas: 00.00.04.08-RH2 Tues. May 5, 11:41:51 PST 2009
megasas: 0x1028:0x0015:0x1028:0x1f03: bus 2:slot 14:func 0
GSI 19 sharing vector 0x52 and IRQ 19
ACPI: PCI Interrupt 0000:02:0e.0[A] -> GSI 78 (level, low) -> IRQ 82
megasas: FW now in Ready state
scsi0 : LSI SAS based MegaRAID driver
  Vendor: ATA       Model: WDC WD2500JS-75N  Rev: 2E04
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: WDC WD2500JS-75N  Rev: 2E04
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: DP        Model: BACKPLANE         Rev: 1.05
  Type:   Enclosure                          ANSI SCSI revision: 05
  Vendor: DELL      Model: PERC 5/i          Rev: 1.03
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 10 08
SCSI device sda: drive cache: none w/ FUA
SCSI device sda: 487063552 512-byte hdwr sectors (249377 MB)
sda: Write Protect is off
sda: Mode Sense: 1f 00 10 08
SCSI device sda: drive cache: none w/ FUA
 sda: sda1 sda2 sda3
usb 1-5: configuration #1 chosen from 1 choice
hub 1-5:1.0: USB hub found
hub 1-5:1.0: 4 ports detected
sd 0:2:0:0: Attached scsi disk sda
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: [email protected]
device-mapper: dm-raid45: initialized v0.2594l
usb 3-2: new low speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
input: Raritan MCIM-USB as /class/input/input0
input: USB HID v1.10 Keyboard [Raritan MCIM-USB] on usb-0000:00:1d.1-2
input: Raritan MCIM-USB as /class/input/input1
input: USB HID v1.10 Mouse [Raritan MCIM-USB] on usb-0000:00:1d.1-2
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: sda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 7816265
ext3_orphan_cleanup: deleting unreferenced inode 7816264
EXT3-fs: sda1: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
type=1404 audit(1483710435.201:2): selinux=0 auid=4294967295 ses=4294967295
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v1.9.3 (March 17, 2009)
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 16 (level, low) -> IRQ 169
input: PC Speaker as /class/input/input2
EDAC MC: Ver: 2.0.1 Sep  3 2009
EDAC MC0: Giving out device to i5000_edac.c I5000: DEV 0000:00:10.0
intel_rng: FWH not detected
hda: ATAPI 24X DVD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 0015c5eaf218
ACPI: PCI Interrupt 0000:09:00.0[A] -> GSI 16 (level, low) -> IRQ 169
libata version 3.00 loaded.
scsi 0:0:8:0: Attached scsi generic sg0 type 13
sd 0:2:0:0: Attached scsi generic sg1 type 0
eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B1) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 0015c5eaf21a
floppy0: no floppy controllers found
lp: driver loaded but no devices found
ACPI: Power Button (FF) [PWRF]
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda1, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2096472k swap on /dev/sda3.  Priority:-1 extents:1 across:2096472k


*output of 'lshw'*

    description: Rack Mount Chassis
    product: PowerEdge 1950 ()
    vendor: Winbond Electronics
    serial: 38GT3C1
    width: 64 bits
    capabilities: smbios-2.5 dmi-2.5 vsyscall64 vsyscall32
    configuration: boot=normal chassis=rackmount 
uuid=44454C4C-3800-1047-8054-B3C04F334331
  *-core
       description: Motherboard
       product: 0NK937
       vendor: Winbond Electronics
       physical id: 0
       version: A00
     *-firmware
          description: BIOS
          vendor: Winbond Electronics
          physical id: 0
          version: 2.7.0
          date: 10/30/2010
          size: 64KiB
          capacity: 960KiB
          capabilities: isa pci pnp upgrade shadowing escd cdboot bootselect 
edd int13floppytoshiba int13floppy360 int13floppy1200 int13floppy720 
int5printscreen int9keyboard int14serial int17printer int10video acpi usb 
biosbootspecification netboot
     *-cpu:0
          description: CPU
          product: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz
          vendor: Intel Corp.
          physical id: 400
          bus info: cpu@0
          version: Intel(R) Xeon(R) CPU            5110  @ 1.60GHz
          slot: CPU1
          size: 1600MHz
          capacity: 3600MHz
          width: 64 bits
          clock: 1066MHz
          capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce 
cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss 
ht tm syscall nx constant_tsc pni monitor ds_cpl vmx tm2 cx16 xtpr lahf_lm
          configuration: cores=2 enabledcores=2 threads=2
        *-cache:0
             description: L1 cache
             physical id: 700
             size: 64KiB
             capacity: 64KiB
             capabilities: internal write-back data
        *-cache:1
             description: L2 cache
             physical id: 701
             size: 4MiB
             capacity: 4MiB
             capabilities: internal write-back unified
     *-cpu:1 DISABLED
          description: CPU [empty]
          vendor: Intel
          physical id: 401
          slot: CPU2
          capabilities: x86-64
     *-memory
          description: System Memory
          physical id: 1000
          slot: System board or motherboard
          size: 6GiB
  *<snip>*
     *-pci:0
          description: Host bridge
          product: 5000X Chipset Memory Controller Hub
          vendor: Intel Corporation
          physical id: 100
          bus info: pci@0000:00:00.0
          version: 12
          width: 32 bits
          clock: 33MHz
        *-pci:0
             description: PCI bridge
             product: 5000 Series Chipset PCI Express x4 Port 2
             vendor: Intel Corporation
             physical id: 2
             bus info: pci@0000:00:02.0
             version: 12
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm msi pciexpress normal_decode bus_master 
cap_list
             configuration: driver=pcieport-driver
             resources: irq:185 memory:f2000000-f7ffffff
           *-pci:0
                description: PCI bridge
                product: 6311ESB/6321ESB PCI Express Upstream Port
                vendor: Intel Corporation
                physical id: 0
                bus info: pci@0000:06:00.0
                version: 01
                width: 32 bits
                clock: 33MHz
                capabilities: pci pciexpress pm normal_decode bus_master 
cap_list
                configuration: driver=pcieport-driver
                resources: irq:169 memory:f4000000-f7ffffff
              *-pci:0
                   description: PCI bridge
                   product: 6311ESB/6321ESB PCI Express Downstream Port E1
                   vendor: Intel Corporation
                   physical id: 0
                   bus info: pci@0000:07:00.0
                   version: 01
                   width: 32 bits
                   clock: 33MHz
                   capabilities: pci pciexpress msi pm normal_decode bus_master 
cap_list
                   configuration: driver=pcieport-driver
                   resources: irq:50 memory:f4000000-f7ffffff
                 *-pci
                      description: PCI bridge
                      product: EPB PCI-Express to PCI-X Bridge
                      vendor: Broadcom
                      physical id: 0
                      bus info: pci@0000:08:00.0
                      version: c2
                      width: 32 bits
                      clock: 33MHz
                      capabilities: pci pciexpress pcix pm normal_decode 
bus_master cap_list
                      resources: memory:f4000000-f7ffffff
                    *-network DISABLED
                         description: Ethernet interface
                         product: NetXtreme II BCM5708 Gigabit Ethernet
                         vendor: Broadcom Corporation
                         physical id: 0
                         bus info: pci@0000:09:00.0
                         logical name: eth1
                         version: 11
                         serial: 00:15:c5:ea:f2:1a
                         capacity: 1Gbit/s
                         width: 64 bits
                         clock: 66MHz
                         capabilities: pcix pm vpd msi bus_master cap_list 
ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation
                         configuration: autonegotiation=on broadcast=yes 
driver=bnx2 driverversion=1.9.3 duplex=half firmware=1.8.0 latency=64 link=yes 
mingnt=64 multicast=yes port=twisted pair
                         resources: irq:169 memory:f4000000-f5ffffff
              *-pci:1
                   description: PCI bridge
                   product: 6311ESB/6321ESB PCI Express Downstream Port E2
                   vendor: Intel Corporation
                   physical id: 1
                   bus info: pci@0000:07:01.0
                   version: 01
                   width: 32 bits
                   clock: 33MHz
                   capabilities: pci pciexpress msi pm normal_decode bus_master 
cap_list
                   configuration: driver=pcieport-driver
                   resources: irq:58
           *-pci:1
                description: PCI bridge
                product: 6311ESB/6321ESB PCI Express to PCI-X Bridge
                vendor: Intel Corporation
                physical id: 0.3
                bus info: pci@0000:06:00.3
                version: 01
                width: 32 bits
                clock: 33MHz
                capabilities: pci pciexpress pm pcix normal_decode bus_master 
cap_list
        *-pci:1
             description: PCI bridge
             product: 5000 Series Chipset PCI Express x4 Port 3
             vendor: Intel Corporation
             physical id: 3
             bus info: pci@0000:00:03.0
             version: 12
             width: 32 bits
             clock: 33MHz
             capabilities: pci pm msi pciexpress normal_decode bus_master 
cap_list
             configuration: driver=pcieport-driver
             resources: irq:193 memory:fc300000-fc5fffff 
ioport:d8000000(size=1048576)
           *-pci:0
                description: PCI bridge
                product: 80333 Segment-A PCI Express-to-PCI Express Bridge
                vendor: Intel Corporation
                physical id: 0
                bus info: pci@0000:01:00.0
                version: 00
                width: 32 bits
                clock: 33MHz
                capabilities: pci pciexpress msi pm pcix normal_decode 
bus_master cap_list
                resources: memory:fc400000-fc5fffff 
ioport:d8000000(size=1048576)
              *-storage
                   description: RAID bus controller
                   product: PowerEdge Expandable RAID controller 5
                   vendor: Winbond Electronics
                   physical id: e
                   bus info: pci@0000:02:0e.0
                   logical name: scsi0
                   version: 00
                   width: 32 bits
                   clock: 66MHz
                   capabilities: storage pm msi pcix bus_master cap_list rom
                   configuration: driver=megaraid_sas latency=32 mingnt=128
                   resources: irq:82 memory:d80f0000-d80fffff(prefetchable) 
memory:fc5c0000-fc5dffff memory:fc400000-fc407fff(prefetchable)
                 *-enclosure UNCLAIMED
                      description: SCSI Enclosure
                      product: BACKPLANE
                      vendor: DP
                      physical id: 0.8.0
                      bus info: scsi@0:0.8.0
                      version: 1.05
                      configuration: ansiversion=5
                 *-disk
                      description: SCSI Disk
                      product: PERC 5/i
                      vendor: Winbond Electronics
                      physical id: 2.0.0
                      bus info: scsi@0:2.0.0
                      logical name: /dev/sda
                      version: 1.03
                      serial: 00e335057e3f820b1c00e36c40b08801
                      size: 232GiB (249GB)
                      capabilities: partitioned partitioned:dos
                      configuration: ansiversion=5 signature=00000080
                    *-volume:0
                         description: EXT3 volume
                         vendor: Linux
                         physical id: 1
                         bus info: scsi@0:2.0.0,1
                         logical name: /dev/sda1
                         logical name: /
                         version: 1.0
                         serial: ff81bca6-ac62-4a95-9110-ea4085368a4d
                         size: 30GiB
                         capacity: 30GiB
                         capabilities: primary bootable journaled 
extended_attributes large_files recover ext3 ext2 initialized
                         configuration: created=2007-04-24 11:03:03 
filesystem=ext3 label=/ lastmountpoint=/mnt/hormel-root modified=2017-01-06 
08:47:53 mount.fstype=ext3 mount.options=rw,data=ordered mounted=2017-01-06 
08:47:53 state=mounted
                    *-volume:1
                         description: EXT3 volume
                         vendor: Linux
                         physical id: 2
                         bus info: scsi@0:2.0.0,2
                         logical name: /dev/sda2
                         logical name: /opt
                         version: 1.0
                         serial: a8f72fb2-4fc1-442d-99ff-f7657b61acaf
                         size: 200GiB
                         capacity: 200GiB
                         capabilities: primary journaled extended_attributes 
large_files recover ext3 ext2 initialized
                         configuration: created=2007-04-24 11:03:53 
filesystem=ext3 label=/opt1 modified=2017-01-06 08:47:53 mount.fstype=ext3 
mount.options=rw,data=ordered mounted=2017-01-06 08:47:53 state=mounted
                    *-volume:2
                         description: Linux swap volume
                         physical id: 3
                         bus info: scsi@0:2.0.0,3
                         logical name: /dev/sda3
                         version: 1
                         serial: 32265d00-d09e-496c-8dcb-8809724c1734
                         size: 2047MiB
                         capacity: 2047MiB
                         capabilities: primary nofs swap initialized
                         configuration: filesystem=swap label=SWAP-sda3 
pagesize=4096
           *-pci:1


_______________________________________________
Linux-PowerEdge mailing list
[email protected]
https://lists.us.dell.com/mailman/listinfo/linux-poweredge

Reply via email to