From: Geert Uytterhoeven <[email protected]> Warning (unit_address_vs_reg): Node /keyboard/button@1 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /keyboard/button@2 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /keyboard/button@3 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /keyboard/button@4 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /regulator@1 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /regulator@2 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /regulator@3 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /regulator@4 has a unit name, but no reg property Warning (unit_address_vs_reg): Node /i2c@8 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <[email protected]> Signed-off-by: Simon Horman <[email protected]> --- arch/arm/boot/dts/r8a7790-lager.dts | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 749ba02b6a53..9d20ace33b01 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -76,28 +76,28 @@ keyboard { compatible = "gpio-keys"; - button@1 { + one { linux,code = <KEY_1>; label = "SW2-1"; wakeup-source; debounce-interval = <20>; gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; }; - button@2 { + two { linux,code = <KEY_2>; label = "SW2-2"; wakeup-source; debounce-interval = <20>; gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; }; - button@3 { + three { linux,code = <KEY_3>; label = "SW2-3"; wakeup-source; debounce-interval = <20>; gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; }; - button@4 { + four { linux,code = <KEY_4>; label = "SW2-4"; wakeup-source; @@ -119,7 +119,7 @@ }; }; - fixedregulator3v3: fixedregulator@0 { + fixedregulator3v3: regulator-3v3 { compatible = "regulator-fixed"; regulator-name = "fixed-3.3V"; regulator-min-microvolt = <3300000>; @@ -128,7 +128,7 @@ regulator-always-on; }; - vcc_sdhi0: regulator@1 { + vcc_sdhi0: regulator-vcc-sdhi0 { compatible = "regulator-fixed"; regulator-name = "SDHI0 Vcc"; @@ -139,7 +139,7 @@ enable-active-high; }; - vccq_sdhi0: regulator@2 { + vccq_sdhi0: regulator-vccq-sdhi0 { compatible = "regulator-gpio"; regulator-name = "SDHI0 VccQ"; @@ -152,7 +152,7 @@ 1800000 0>; }; - vcc_sdhi2: regulator@3 { + vcc_sdhi2: regulator-vcc-sdhi2 { compatible = "regulator-fixed"; regulator-name = "SDHI2 Vcc"; @@ -163,7 +163,7 @@ enable-active-high; }; - vccq_sdhi2: regulator@4 { + vccq_sdhi2: regulator-vccq-sdhi2 { compatible = "regulator-gpio"; regulator-name = "SDHI2 VccQ"; @@ -263,7 +263,7 @@ * instantiate the slave device at runtime according to the documentation. * You can then communicate with the slave via IIC3. */ - i2cexio: i2c@8 { + i2cexio: i2c-8 { compatible = "i2c-demux-pinctrl"; i2c-parent = <&iic0>, <&i2c0>; i2c-bus-name = "i2c-exio"; -- 2.1.4
