We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+rene...@sang-engineering.com>
---
drivers/mmc/host/tmio_mmc.h | 3 +++
drivers/mmc/host/tmio_mmc_pio.c | 38 ++++++++++++++++++++++++++------------
2 files changed, 29 insertions(+), 12 deletions(-)
diff --git a/drivers/mmc/host/tmio_mmc.h b/drivers/mmc/host/tmio_mmc.h
index 4b501f2d529f6e..637581faf756b1 100644
--- a/drivers/mmc/host/tmio_mmc.h
+++ b/drivers/mmc/host/tmio_mmc.h
@@ -79,6 +79,9 @@
#define CLK_CTL_DIV_MASK 0xff
#define CLK_CTL_SCLKEN BIT(8)
+#define CARD_OPT_WIDTH8 BIT(13)
+#define CARD_OPT_WIDTH BIT(15)
+
#define TMIO_BBS 512 /* Boot block size */
/* Definitions for values the CTRL_SDIO_STATUS register can take. */
diff --git a/drivers/mmc/host/tmio_mmc_pio.c b/drivers/mmc/host/tmio_mmc_pio.c
index 46b5a456243b84..a0f05eb4f34490 100644
--- a/drivers/mmc/host/tmio_mmc_pio.c
+++ b/drivers/mmc/host/tmio_mmc_pio.c
@@ -340,7 +340,9 @@ static int tmio_mmc_start_command(struct tmio_mmc_host
*host, struct mmc_command
switch (mmc_resp_type(cmd)) {
case MMC_RSP_NONE: c |= RESP_NONE; break;
- case MMC_RSP_R1: c |= RESP_R1; break;
+ case MMC_RSP_R1:
+ case MMC_RSP_R1_NO_CRC:
+ c |= RESP_R1; break;
case MMC_RSP_R1B: c |= RESP_R1B; break;
case MMC_RSP_R2: c |= RESP_R2; break;
case MMC_RSP_R3: c |= RESP_R3; break;
@@ -737,12 +739,13 @@ static int tmio_mmc_start_data(struct tmio_mmc_host *host,
pr_debug("setup data transfer: blocksize %08x nr_blocks %d\n",
data->blksz, data->blocks);
- /* Some hardware cannot perform 2 byte requests in 4 bit mode */
- if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4) {
+ /* Some hardware cannot perform 2 byte requests in 4/8 bit mode */
+ if (host->mmc->ios.bus_width == MMC_BUS_WIDTH_4 ||
+ host->mmc->ios.bus_width == MMC_BUS_WIDTH_8) {
int blksz_2bytes = pdata->flags & TMIO_MMC_BLKSZ_2BYTES;
if (data->blksz < 2 || (data->blksz < 4 && !blksz_2bytes)) {
- pr_err("%s: %d byte block unsupported in 4 bit mode\n",
+ pr_err("%s: %d byte block unsupported in 4/8 bit
mode\n",
mmc_hostname(host->mmc), data->blksz);
return -EINVAL;
}
@@ -922,14 +925,16 @@ static void tmio_mmc_power_off(struct tmio_mmc_host *host)
static void tmio_mmc_set_bus_width(struct tmio_mmc_host *host,
unsigned char bus_width)
{
- switch (bus_width) {
- case MMC_BUS_WIDTH_1:
- sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x80e0);
- break;
- case MMC_BUS_WIDTH_4:
- sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x00e0);
- break;
- }
+ u16 reg = sd_ctrl_read16(host, CTL_SD_MEM_CARD_OPT)
+ & ~(CARD_OPT_WIDTH | CARD_OPT_WIDTH8);
+
+ /* reg now applies to MMC_BUS_WIDTH_4 */
+ if (bus_width == MMC_BUS_WIDTH_1)
+ reg |= CARD_OPT_WIDTH;
+ else if (bus_width == MMC_BUS_WIDTH_8)
+ reg |= CARD_OPT_WIDTH8;
+
+ sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, reg);
}
/* Set MMC clock / power.
@@ -1149,6 +1154,15 @@ int tmio_mmc_host_probe(struct tmio_mmc_host *_host,
!mmc_card_is_removable(mmc) ||
mmc->slot.cd_irq >= 0);
+ /*
+ * On Gen2+, eMMC with NONREMOVABLE currently fails because native
+ * hotplug gets disabled. It seems RuntimePM related yet we need further
+ * research. Since we are planning a PM overhaul anyway, let's enforce
+ * for now the device being active by enabling native hotplug always.
+ */
+ if (pdata->flags & TMIO_MMC_MIN_RCAR2)
+ _host->native_hotplug = true;
+
if (tmio_mmc_clk_enable(_host) < 0) {
mmc->f_max = pdata->hclk;
mmc->f_min = mmc->f_max / 512;
--
2.9.3
