On Fri, Oct 05, 2018 at 10:09:51AM -0500, Chris Brandt wrote:
> Add device tree binding documentation and header file for Renesas R7S9210
> (RZ/A2) SoCs.
>
> Signed-off-by: Chris Brandt <[email protected]>
> ---
> .../bindings/pinctrl/renesas,rza2-pinctrl.txt | 76
> ++++++++++++++++++++++
> include/dt-bindings/pinctrl/r7s9210-pinctrl.h | 47 +++++++++++++
> 2 files changed, 123 insertions(+)
> create mode 100644
> Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
> create mode 100644 include/dt-bindings/pinctrl/r7s9210-pinctrl.h
>
> diff --git
> a/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
> b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
> new file mode 100644
> index 000000000000..5f338054f493
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt
> @@ -0,0 +1,76 @@
> +Renesas RZ/A2 combined Pin and GPIO controller
> +
> +The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO
> controller.
> +Pin multiplexing and GPIO configuration is performed on a per-pin basis.
> +Each port features up to 8 pins, each of them configurable for GPIO
> +function (port mode) or in alternate function mode.
> +Up to 8 different alternate function modes exist for each single pin.
> +
> +Pin controller node
> +-------------------
> +
> +Required properties:
> + - compatible: should be:
> + - "renesas,r7s9210-pinctrl": for RZ/A2M
> +
> + - reg
> + address base and length of the memory area where the pin controller
> + hardware is mapped to.
> +
> +Optional properties:
> + - gpio-controller
> + Include this in order to enable GPIO functionality. When included, both
> + gpio_cells and gpio_ranges are then required.
> + - #gpio-cells
> + Must be 2
> + - gpio-ranges
> + Expresses the total number GPIO ports/pins in this SoC
Are these really optional? I guess in theory a board could use no GPIOs,
but that seems unlikely.
> +
> +
> +Example: Pin controller node for RZ/A2M SoC (r7s9210)
> +
> + pinctrl: pin-controller@fcffe000 {
> + compatible = "renesas,r7s9210-pinctrl";
> + reg = <0xfcffe000 0x9D1>;
> +
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pinctrl 0 0 176>;
> + };
> +
> +Sub-nodes
> +---------
> +
> +The child nodes of the pin controller node describe a pin multiplexing
> +function or a GPIO controller alternatively.
But the parent is already a GPIO controller. This needs to be fully
defined.
> +
> +- Pin multiplexing sub-nodes:
> + A pin multiplexing sub-node describes how to configure a set of
> + (or a single) pin in some desired alternate function mode.
> + The values for the pinmux properties are a combination of port name, pin
> + number and the desired function index. Use the RZA2_PINMUX macro located
> + in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily define these.
> + For assigning GPIO pins, use the macro RZA2_PIN_ID also in
> r7s9210-pinctrl.h
> + to express the desired port pin.
> +
> + Example: Board specific pins configuration
> +
> + &pinctrl {
> + /* Serial Console */
> + scif4_pins: serial4 {
> + pinmux = <RZA2_PINMUX(P9, 0, 4)>, /* TxD4 */
> + <RZA2_PINMUX(P9, 1, 4)>; /* RxD4 */
> + };
> + };
> +
> + Example: Assigning a GPIO:
> +
> + leds {
> + status = "okay";
> + compatible = "gpio-leds";
> +
> + led0 {
> + /* P6_0 */
> + gpios = <&pinctrl RZA2_PIN_ID(P6, 0) GPIO_ACTIVE_HIGH>;
> + };
> + };
