On Thu, Jan 10, 2019 at 05:33:57PM +0100, Niklas Söderlund wrote:
> Hi Keneko-san,
>
> Thanks for your work.
>
> Comments to this patch applies to all patches in this series.
>
> On 2018-12-21 05:49:39 +0900, Yoshihiro Kaneko wrote:
> > From: Dien Pham <[email protected]>
> >
> > [dien.pham.ry: arm64: dts: r8a7795: Add support IPA for CA53 core]
> >
> > Setup a thermal zone driven by SoC temperature sensor.
> > Create passive trip points and bind them to CPUFreq cooling
> > device that supports power extension.
> >
> > In R-Car Gen3, IPA is supportted for only one channel
> > (on H3/M3/M3N board, it is channel THS3). Reason:
> > Currently, IPA controls base on only CPU temperature.
> > And only one thermal channel is assembled closest
> > CPU cores is selected as target of IPA.
> > If other channels are used, IPA controlling is not properly.
> >
> > Signed-off-by: Keita Kobayashi <[email protected]>
> > [gaku.inami.xw: fix the trip temperature for cooling-device]
> > [gaku.inami.xw: fix the power coefficient]
> > Signed-off-by: Gaku Inami <[email protected]>
> > Signed-off-by: Hien Dang <[email protected]>
> > Signed-off-by: An Huynh <[email protected]>
> > [takeshi.kihara.df: fix W=1 dtc unit_address_vs_reg warnings]
> > Signed-off-by: Takeshi Kihara <[email protected]>
> > Signed-off-by: Yoshihiro Kaneko <[email protected]>
> > ---
> >
> > This patch is based on the devel branch of Simon Horman's renesas tree.
> >
> > arch/arm64/boot/dts/renesas/r8a7795.dtsi | 64
> > ++++++++++++++------------------
> > 1 file changed, 27 insertions(+), 37 deletions(-)
> >
> > diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
> > b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
> > index af9605d..dd52b50 100644
> > --- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
> > +++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
> > @@ -155,6 +155,9 @@
> > power-domains = <&sysc R8A7795_PD_CA57_CPU0>;
> > next-level-cache = <&L2_CA57>;
> > enable-method = "psci";
> > + dynamic-power-coefficient = <854>;
> > + cooling-min-level = <0>;
> > + cooling-max-level = <2>;
>
> I can't find any documentation or code which makes use of the
> cooling-min-level and cooling-max-level properties on v5.0-rc1. What is
> the intended usage for these properties?
It looks like these properties were removed in v4.17-rc1 by
bbcf071969b2 ("cpufreq: cpu0: rename driver and internals to 'cpufreq_dt'")
and should be dropped from this and similar patches.
>
> > clocks = <&cpg CPG_CORE R8A7795_CLK_Z>;
> > operating-points-v2 = <&cluster0_opp>;
> > capacity-dmips-mhz = <1024>;
> > @@ -207,6 +210,10 @@
> > power-domains = <&sysc R8A7795_PD_CA53_CPU0>;
> > next-level-cache = <&L2_CA53>;
> > enable-method = "psci";
> > + #cooling-cells = <2>;
> > + dynamic-power-coefficient = <277>;
> > + cooling-min-level = <0>;
> > + cooling-max-level = <2>;
> > clocks = <&cpg CPG_CORE R8A7795_CLK_Z2>;
> > operating-points-v2 = <&cluster1_opp>;
> > capacity-dmips-mhz = <535>;
> > @@ -3098,58 +3105,30 @@
> > polling-delay-passive = <250>;
> > polling-delay = <1000>;
> > thermal-sensors = <&tsc 0>;
> > + sustainable-power = <6313>;
> >
> > trips {
> > - sensor1_passive: sensor1-passive {
> > - temperature = <95000>;
> > - hysteresis = <1000>;
> > - type = "passive";
> > - };
> > sensor1_crit: sensor1-crit {
> > temperature = <120000>;
> > hysteresis = <1000>;
> > type = "critical";
> > };
> > };
> > -
> > - cooling-maps {
> > - map0 {
> > - trip = <&sensor1_passive>;
> > - cooling-device = <&a57_0 4 4>,
> > - <&a57_1 4 4>,
> > - <&a57_2 4 4>,
> > - <&a57_3 4 4>;
> > - };
> > - };
> > };
> >
> > sensor_thermal2: sensor-thermal2 {
> > polling-delay-passive = <250>;
> > polling-delay = <1000>;
> > thermal-sensors = <&tsc 1>;
> > + sustainable-power = <6313>;
> >
> > trips {
> > - sensor2_passive: sensor2-passive {
> > - temperature = <95000>;
> > - hysteresis = <1000>;
> > - type = "passive";
> > - };
> > sensor2_crit: sensor2-crit {
> > temperature = <120000>;
> > hysteresis = <1000>;
> > type = "critical";
> > };
> > };
> > -
> > - cooling-maps {
> > - map0 {
> > - trip = <&sensor2_passive>;
> > - cooling-device = <&a57_0 4 4>,
> > - <&a57_1 4 4>,
> > - <&a57_2 4 4>,
> > - <&a57_3 4 4>;
> > - };
> > - };
> > };
> >
> > sensor_thermal3: sensor-thermal3 {
> > @@ -3158,11 +3137,18 @@
> > thermal-sensors = <&tsc 2>;
> >
> > trips {
> > - sensor3_passive: sensor3-passive {
> > - temperature = <95000>;
> > + threshold: trip-point0 {
> > + temperature = <90000>;
> > + hysteresis = <1000>;
> > + type = "passive";
> > + };
>
> What is the usage of trip-point0? The label threshold is never
> referenced anywhere, or am I missing something?
Good point. Given this patch in its current form I think trip-point0
should be dropped.
>
> > +
> > + target: trip-point1 {
> > + temperature = <100000>;
> > hysteresis = <1000>;
> > type = "passive";
> > };
> > +
> > sensor3_crit: sensor3-crit {
> > temperature = <120000>;
> > hysteresis = <1000>;
> > @@ -3172,11 +3158,15 @@
> >
> > cooling-maps {
> > map0 {
> > - trip = <&sensor3_passive>;
> > - cooling-device = <&a57_0 4 4>,
> > - <&a57_1 4 4>,
> > - <&a57_2 4 4>,
> > - <&a57_3 4 4>;
> > + trip = <&target>;
> > + cooling-device = <&a57_0 0 2>;
>
> We have 5 (0-4) cooling states for the A57s on this SoC. Out of
> curiosity why allow states 0-2 here and not force it do more cooling or
> keep the to max cooling (4) as before this change as this is set to a
> trip point with a rather large temperature? Not saying this is wrong
> only curious :-)
This I do not know. Do you think it would be worth following-up on
internally?
> > + contribution = <1024>;
> > + };
> > +
> > + map1 {
> > + trip = <&target>;
> > + cooling-device = <&a53_0 0 2>;
> > + contribution = <1024>;
> > };
> > };
> > };
> > --
> > 1.9.1
> >
>
> --
> Regards,
> Niklas Söderlund
>
