Hello PPL,
I've got 2 scsi cdroms on my scsi chain. The first is a
Plextor cd-r that is mountable. The second is a Pioneer DR-506S which
whenever the cd-r is on the chain, will not be mountable. If I remove the
cd-r from the chain the cdrom works perfectly. Now I haven't been able to
define this as a non-jumper termination problem. The cdrom (I was told)
was set as terminant, and the cd-r was non-terminant. They both have
different IDs also. Here is some info on my system:
Motherboard: ASUS P2B-D
SCSI card: Symbios Logic SYM8951U
SCSI card: Symbios Logic 875
and so that this doesn't get redundant if I need to respond, here's whats
being said in my messages file:
Jan 17 11:08:25 kevlar kernel: Vendor: QUANTUM Model: VIKING II 4.5WLS Rev: 3506
Jan 17 11:08:25 kevlar kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 17 11:08:25 kevlar kernel: Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Jan 17 11:08:25 kevlar kernel: ncr53c895-0-<0,0>: tagged command queue depth set to 4
Jan 17 11:08:25 kevlar kernel: Vendor: UMAX Model: Astra 1220S Rev: V1.3
Jan 17 11:08:25 kevlar kernel: Type: Scanner ANSI SCSI
revision: 02
Jan 17 11:08:25 kevlar kernel: Detected scsi generic sgb at scsi1, channel 0, id 3,
lun 0
Jan 17 11:08:25 kevlar kernel: Vendor: PLEXTOR Model: CD-R PX-R412C Rev: 1.04
Jan 17 11:08:25 kevlar kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 17 11:08:25 kevlar kernel: Detected scsi CD-ROM sr0 at scsi1, channel 0, id 4, lun 0
Jan 17 11:08:25 kevlar kernel: Vendor: IOMEGA Model: ZIP 100 Rev: J.03
Jan 17 11:08:25 kevlar kernel: Type: Direct-Access ANSI SCSI
revision: 02
Jan 17 11:08:25 kevlar kernel: Detected scsi removable disk sdb at scsi1, channel 0,
id 5, lun 0
Jan 17 11:08:25 kevlar kernel: Vendor: PIONEER Model: CD-ROM DR-U06S Rev: 1.05
Jan 17 11:08:25 kevlar kernel: Type: CD-ROM ANSI SCSI
revision: 02
Jan 17 11:08:25 kevlar kernel: Detected scsi CD-ROM sr1 at scsi1, channel 0, id 6, lun 0
Jan 17 11:08:25 kevlar kernel: scsi : detected 2 SCSI cdroms 2 SCSI disks total.
Jan 17 11:08:25 kevlar kernel: ncr53c875-1-<4,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
Jan 17 11:08:25 kevlar kernel: sr0: scsi3-mmc drive: 12x/12x writer cd/rw xa/form2
cdda caddy
Jan 17 11:08:25 kevlar kernel: Uniform CDROM driver Revision: 2.51
Jan 17 11:08:25 kevlar kernel: ncr53c875-1-<6,*>: FAST-20 SCSI 16.0 MB/s (62 ns,
offset 16)
Jan 17 11:08:25 kevlar kernel: scsi1 channel 0 : resetting for second half of retries.
Jan 17 11:08:25 kevlar kernel: SCSI bus is being reset for host 1 channel 0.
Jan 17 11:08:25 kevlar kernel: ncr53c8xx_reset: pid=71 reset_flags=1 serial_number=0
serial_number_at_timeout=0
Jan 17 11:08:25 kevlar kernel: ncr53c875-1: resetting, command processing suspended
for 2 seconds
Jan 17 11:08:25 kevlar kernel: scsi1: device driver called scsi_done() for a
syncronous reset.
Jan 17 11:08:25 kevlar kernel: ncr53c875-1: restart (scsi reset).
Jan 17 11:08:25 kevlar kernel: ncr53c875-1: enabling clock multiplier
Jan 17 11:08:25 kevlar kernel: ncr53c875-1: Downloading SCSI SCRIPTS.
Jan 17 11:08:25 kevlar kernel: ncr53c875-1: command processing resumed
Jan 17 11:08:25 kevlar kernel: ncr53c875-1-<6,*>: FAST-20 SCSI 16.0 MB/s (62 ns,
offset 16)
Jan 17 11:08:25 kevlar kernel: sr1: CDROM (ioctl) error, command: Mode Sense 00 2a 00
80 00
Jan 17 11:08:25 kevlar kernel: extra data not valid Current error sr00:00: sense key
Aborted Command
Jan 17 11:08:25 kevlar kernel: Additional sense indicates Initiator detected error
message received
Jan 17 11:08:25 kevlar kernel: sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Jan 17 11:08:25 kevlar kernel: ncr53c895-0-<0,*>: WIDE SCSI (16 bit) enabled.
Jan 17 11:08:25 kevlar kernel: ncr53c895-0-<0,*>: FAST-40 WIDE SCSI 80.0 MB/s (25 ns,
offset 31)
Jan 17 11:08:25 kevlar kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
8910423 [4350 MB] [4.4 GB]
Jan 17 11:08:25 kevlar kernel: ncr53c875-1-<5,*>: SYNC transfers not supported.
Also here is the debugg info when trying to mount the cdrom:
sr1: CDROM (ioctl) error, command: Read TOC 00 00 00 00 00
00 00 0c 40
extra data not valid Current error sr00:00: sense key Aborted Command
Additional sense indicates Initiator detected error message received
scsi1 channel 0 : resetting for second half of retries.
SCSI bus is being reset for host 1 channel 0.
ncr53c8xx_reset: pid=4170 reset_flags=1 serial_number=0
serial_number_at_timeout=0
ncr53c875-1: resetting, command processing suspended for 2 seconds
scsi1: device driver called scsi_done() for a syncronous reset.
ncr53c875-1: enabling clock multiplier
ncr53c875-1: Downloading SCSI SCRIPTS.
ncr53c875-1: command processing resumed
Thanks for making it this far, and please don't rip me too hard if there's
a really simple solution, I'm very new to scsi.
~~Kev
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
