Forward of a post I made to [EMAIL PROTECTED], as this is probably a more
appropriate place.
TIA
Richard
>From: "Richard Mottershead" <[EMAIL PROTECTED]>
>To: [EMAIL PROTECTED]
>Subject: Problems with multiple devices on AVA-2904
>Date: Thu, 02 Dec 1999 17:01:33 GMT
>
>Sorry, about the lengthy message but I included some dumps.
>
>Firstly, My Machine Specification:
> P5-166
> IDE HD/CDROM
> ADAPTEC AVA-2904
> Ricoh MP6200S SCSI CD-RW Drive
> Minolta Scan Dual SCSI Film Scanner
> AverMedia TVCapture Card
>
> Corel Linux 1.0 with 2.2.12 Kernel.
>
>I have a problem when loading the aic7xxx driver with both the CD-RW and
>Scanner turned on. Without the scanner turned on the CD-RW works fine.
>
>I have the same problem with driver versions 5.1.19 and 5.1.20.
>
>I tried loadin it as in the kernel ( machine wont boot), so I rebuilt the
>kernel and used some parameters to give the following information.
>
>This is the content of the 'aic7xxx=dump_card' parameter used when loading
>the module WITHOUT the film scanner.
>---
>
>scsi : 0 hosts.
>(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 18/0
>(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
>(scsi0) Downloading sequencer code... 406 instructions downloaded
>Adaptec AIC-7850 SCSI host adapter at PCI 18/0.
>PCI Dump:
>04:07 05:00 06:90 07:02 08:03 0c:08 0d:40 0e:00 10:01 11:ec 12:00 13:00
>14:00
>15:b0 16:bf 17:fe 28:00 29:00 2a:00 2b:00 30:00 31:00 32:00 33:00 3c:0a
>3d:01
>3e:04 3f:04 40:40 41:01 43:80 44:40 45:01 46:00 47:80
>Card Dump:
>00:00 01:80 02:3f 03:00 04:00 05:07 08:00 09:00 0a:00 0b:05 0c:00 0d:00
>0e:00
>0f:00 10:00 11:a4 18:03 19:00 1a:00 1b:00 1c:00 1d:40 1e:11 1f:00 60:10
>62:0b
>63:00 64:00 65:00 66:00 80:04 81:90 82:78 83:50 84:a1 85:40 86:c0 87:06
>88:00
>89:00 8a:00 8b:00 8c:00 8d:00 8e:00 90:00 91:00 92:00 93:00 94:29 95:00
>97:00
>9a:00 <3>(scsi0) BRKADRINT error(0x20):
> Scratch Ram/SCB Array Ram Parity Error
>(scsi0) SEQADDR=0xb
>9b:07 9c:00 <3>(scsi0) BRKADRINT error(0x20):
> Scratch Ram/SCB Array Ram Parity Error
>(scsi0) SEQADDR=0xc
>9d:07 9e:00 9f:00
>Scratch RAM:
>20:00 21:00 22:00 23:00 24:00 25:00 26:00 27:00 28:ff 29:ff 2a:ff 2b:ff
>2c:ff
>2d:ff 2e:ff 2f:ff 30:00 31:00 32:00 33:ff 34:08 35:01 36:00 37:50 38:01
>39:00
>3a:04 3b:a6 3c:03 3d:01 3e:ff 3f:ff 40:00 41:00 42:60 43:a6 44:03 45:78
>46:a3
>47:c7 48:03 49:00 4a:00 4b:00 4c:00 4d:00 4e:00 4f:00 50:00 51:40 52:01
>53:08
>54:ff 55:ff 56:ff 57:ff 58:ff 59:ff 5a:67 5b:07 5c:ff 5d:ff 5e:ff 5f:ff
>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.20/3.2.4
> <Adaptec AIC-7850 SCSI host adapter>
>scsi : 1 host.
> Vendor: RICOH Model: MP6200S Rev: 2.20
> Type: CD-ROM ANSI SCSI revision: 02
>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
>sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
>
>---
>
>This is the content of the aic7xxx='verbose;0xffff' parameter used when
>loading the module WITHOUT the film scanner.
>
>---
>
>aic7xxx: <Adaptec AIC-7850 SCSI host adapter> at PCI 18/0
>aic7xxx: Initial PCI_COMMAND value was 0x7
>aic7xxx: Initial DEVCONFIG value was 0x80000140
>aic7xxx: Loading serial EEPROM...
>aic7xxx: No SEEPROM available.
>aic7xxx: Using default values.
>(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 18/0
>(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
>(scsi0) BIOS disabled, IO Port 0xec00, IRQ 10
>(scsi0) IO Memory at 0xfebfb000, MMAP Memory at 0xc4098000
>(scsi0) Downloading sequencer code... 406 instructions downloaded
>(scsi0) Resetting channel
>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.20/3.2.4
> <Adaptec AIC-7850 SCSI host adapter>
>scsi : 1 host.
> Vendor: RICOH Model: MP6200S Rev: 2.20
> Type: CD-ROM ANSI SCSI revision: 02
>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
>sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
>
>---
>
>This is the content of the aic7xxx='verbose;0xffff' parameter used when
>loading the module WITH the film scanner. (The insmod was killed).
>
>---
>
>scsi : 0 hosts.
>aic7xxx: <Adaptec AIC-7850 SCSI host adapter> at PCI 18/0
>aic7xxx: Initial PCI_COMMAND value was 0x7
>aic7xxx: Initial DEVCONFIG value was 0x80000140
>aic7xxx: Loading serial EEPROM...
>aic7xxx: No SEEPROM available.
>aic7xxx: Using default values.
>(scsi0) <Adaptec AIC-7850 SCSI host adapter> found at PCI 18/0
>(scsi0) Narrow Channel, SCSI ID=7, 3/255 SCBs
>(scsi0) BIOS disabled, IO Port 0xec00, IRQ 10
>(scsi0) IO Memory at 0xfebfb000, MMAP Memory at 0xc4098000
>(scsi0) Downloading sequencer code... 406 instructions downloaded
>(scsi0) Resetting channel
>scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.20/3.2.4
> <Adaptec AIC-7850 SCSI host adapter>
>scsi : 1 host.
> Vendor: RICOH Model: MP6200S Rev: 2.20
> Type: CD-ROM ANSI SCSI revision: 02
>Detected scsi CD-ROM sr0 at scsi0, channel 0, id 5, lun 0
>scsi : aborting command due to timeout : pid 144, scsi0, channel 0, id 6,
>lun 0 Test Unit Ready 00 00 00 00 00
>(scsi0:0:6:0) Aborting scb 0, flags 0x6
>SCSI host 0 abort (pid 144) timed out - resetting
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x16
>(scsi0:0:6:0) Bus Device reset, scb flags 0x16, Data-In phase
>(scsi0:0:6:0) SCSISIGI 0x44, SEQADDR 0x10a, SSTAT0 0x0, SSTAT1 0x2
>(scsi0:0:6:0) Queueing device reset command.
>(scsi0:-1:-1:-1) 0 commands found and queued for completion.
>(scsi0:0:6:0) Bus device reset mailed.
>(scsi0:0:6:-1) Reset device, active_scb 0
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning QINFIFO.
>(scsi0:0:6:-1) Cleaning waiting_scbs.
>(scsi0:0:6:-1) Cleaning waiting for selection list.
>(scsi0:0:6:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:-1) Bus Device Reset delivered.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>SCSI host 0 channel 0 reset (pid 144) timed out - trying harder
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x6
>(scsi0:0:-1:-1) Reset channel called, will initiate reset.
>(scsi0:0:-1:-1) Resetting currently active channel.
>(scsi0:0:-1:-1) Channel reset
>(scsi0:0:-1:-1) Reset device, active_scb 0
>(scsi0:0:0:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:1:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:2:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:3:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:4:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:5:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:-1:-1) Cleaning QINFIFO.
>(scsi0:0:-1:-1) Cleaning waiting_scbs.
>(scsi0:0:-1:-1) Cleaning waiting for selection list.
>(scsi0:0:-1:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>SCSI host 0 abort (pid 144) timed out - resetting
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x6
>(scsi0:0:6:0) Bus Device reset, scb flags 0x6, Command phase
>(scsi0:0:6:0) SCSISIGI 0x84, SEQADDR 0x14d, SSTAT0 0x7, SSTAT1 0x2
>(scsi0:0:6:0) Queueing device reset command.
>(scsi0:-1:-1:-1) 0 commands found and queued for completion.
>(scsi0:0:6:0) Bus device reset mailed.
>(scsi0:0:6:-1) Reset device, active_scb 0
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning QINFIFO.
>(scsi0:0:6:-1) Cleaning waiting_scbs.
>(scsi0:0:6:-1) Cleaning waiting for selection list.
>(scsi0:0:6:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:-1) Bus Device Reset delivered.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>SCSI host 0 channel 0 reset (pid 144) timed out - trying harder
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x6
>(scsi0:0:-1:-1) Reset channel called, will initiate reset.
>(scsi0:0:-1:-1) Resetting currently active channel.
>(scsi0:0:-1:-1) Channel reset
>(scsi0:0:-1:-1) Reset device, active_scb 0
>(scsi0:0:0:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:1:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:2:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:3:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:4:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:5:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:-1:-1) Cleaning QINFIFO.
>(scsi0:0:-1:-1) Cleaning waiting_scbs.
>(scsi0:0:-1:-1) Cleaning waiting for selection list.
>(scsi0:0:-1:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>SCSI host 0 abort (pid 144) timed out - resetting
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x6
>(scsi0:0:6:0) Bus Device reset, scb flags 0x6, Data-In phase
>(scsi0:0:6:0) SCSISIGI 0x44, SEQADDR 0x109, SSTAT0 0x0, SSTAT1 0x2
>(scsi0:0:6:0) Queueing device reset command.
>(scsi0:-1:-1:-1) 0 commands found and queued for completion.
>(scsi0:0:6:0) Bus device reset mailed.
>(scsi0:0:6:-1) Reset device, active_scb 0
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning QINFIFO.
>(scsi0:0:6:-1) Cleaning waiting_scbs.
>(scsi0:0:6:-1) Cleaning waiting for selection list.
>(scsi0:0:6:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:-1) Bus Device Reset delivered.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>SCSI host 0 channel 0 reset (pid 144) timed out - trying harder
>SCSI bus is being reset for host 0 channel 0.
>(scsi0:0:6:0) Reset called, scb 0, flags 0x6
>(scsi0:0:-1:-1) Reset channel called, will initiate reset.
>(scsi0:0:-1:-1) Resetting currently active channel.
>(scsi0:0:-1:-1) Channel reset
>(scsi0:0:-1:-1) Reset device, active_scb 0
>(scsi0:0:0:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:1:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:2:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:3:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:4:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:5:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:6:-1) Cleaning up status information and delayed_scbs.
>(scsi0:0:-1:-1) Cleaning QINFIFO.
>(scsi0:0:-1:-1) Cleaning waiting_scbs.
>(scsi0:0:-1:-1) Cleaning waiting for selection list.
>(scsi0:0:-1:-1) Cleaning disconnected scbs list.
>(scsi0:0:6:0) Aborting scb 0
>(scsi0:0:6:0) Aborting scb 1
>(scsi0:-1:-1:-1) 2 commands found and queued for completion.
>scsi : aborting command due to timeout : pid 145, scsi0, channel 0, id 5,
>lun 0 Mode Sense 00 2a 00 80 00
>(scsi0:0:5:0) Aborting scb 0, flags 0x6
>(scsi0:0:5:0) SCB found on waiting list and aborted.
>(scsi0:0:5:0) Aborting scb 0
>(scsi0:-1:-1:-1) 1 commands found and queued for completion.
>sr0: scsi3-mmc drive: 6x/6x writer cd/rw xa/form2 cdda tray
>
>---
>
>This is the /proc/scsi/scsi file after I killed the insmod.
>
>---
>
>Attached devices:
>Host: scsi0 Channel: 00 Id: 05 Lun: 00
> Vendor: RICOH Model: MP6200S Rev: 2.20
> Type: CD-ROM ANSI SCSI revision: 02
>
>---
>
>This is the /proc/scsi/aic7xxx file after I killed the insmod.
>
>---
>
>Adaptec AIC7xxx driver version: 5.1.20/3.2.4
>Compile Options:
> TCQ Enabled By Default : Disabled
> AIC7XXX_PROC_STATS : Enabled
> AIC7XXX_RESET_DELAY : 5
>
>Adapter Configuration:
> SCSI Adapter: Adaptec AIC-7850 SCSI host adapter
> Narrow Controller
> PCI MMAPed I/O Base: 0xfebfb000
>Adapter SEEPROM Config: SEEPROM not found, using defaults.
> Adaptec SCSI BIOS: Disabled
> IRQ: 10
> SCBs: Active 0, Max Active 1,
> Allocated 15, HW 3, Page 255
> Interrupts: 17094
> BIOS Control Word: 0x0000
> Adapter Control Word: 0x0000
> Extended Translation: Disabled
>Disconnect Enable Flags: 0x00ff
>Tag Queue Enable Flags: 0x0000
>Ordered Queue Tag Flags: 0x0000
>Default Tag Queue Depth: 8
> Tagged Queue By Device array for aic7xxx host instance 0:
> {255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
> Actual queue depth per device for aic7xxx host instance 0:
> {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}
>
>Statistics:
>
>(scsi0:0:5:0)
> Device using Narrow/Async transfers.
> Transinfo settings: current(0/0/0/0), goal(0/0/0/0), user(25/15/0/0)
> Total transfers 0 (0 reads and 0 writes)
> < 2K 2K+ 4K+ 8K+ 16K+ 32K+ 64K+ 128K+
> Reads: 0 0 0 0 0 0 0 0
> Writes: 0 0 0 0 0 0 0 0
>
>---
>
>If you require any more information don't hesitate to ask.
>
>Once, I solve this issue and test the scanner software I have, I can
>finally
>kick M$ software off my PC.
>
>TIA
>
>Richard Mottershead
>
>P.S. It works fine under Windows 95 (had to get that one in)
>
>
>______________________________________________________
>Get Your Private, Free Email at http://www.hotmail.com
>
>
>To Unsubscribe: send mail to [EMAIL PROTECTED]
>with "unsubscribe aic7xxx" in the body of the message
______________________________________________________
Get Your Private, Free Email at http://www.hotmail.com
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to [EMAIL PROTECTED]
