Tyan Titan Pro MB w/ 2 180MHz PPro.
PCI Buslogic BT958 SCSI controller
When 2.0.35 kernel boots, I get this scsi info in dmesg:
--------
scsi: ***** BusLogic SCSI Driver Version 2.0.14 of 29 April 1998 *****
scsi: Copyright 1995-1998 by Leonard N. Zubkoff <[EMAIL PROTECTED]>
scsi0: Configuring BusLogic Model BT-958 PCI Wide Ultra SCSI Host Adapter
scsi0: Firmware Version: 5.07B, I/O Address: 0x8000, IRQ Channel:
11/Level
scsi0: PCI Bus: 0, Device: 10, Address: 0xE0000000, Host Adapter SCSI
ID: 7
scsi0: Parity Checking: Enabled, Extended Translation: Enabled
scsi0: Synchronous Negotiation: Ultra, Wide Negotiation: Enabled
scsi0: Disconnect/Reconnect: Enabled, Tagged Queuing: Enabled
scsi0: Scatter/Gather Limit: 128 of 8192 segments, Mailboxes: 211
scsi0: Driver Queue Depth: 211, Host Adapter Queue Depth: 192
scsi0: Tagged Queue Depth: Automatic, Untagged Queue Depth: 3
scsi0: Error Recovery Strategy: Default, SCSI Bus Reset: Enabled
scsi0: SCSI Bus Termination: Both Enabled, SCAM: Enabled, Level 1
scsi0: *** BusLogic BT-958 Initialized Successfully ***
scsi0 : BusLogic BT-958
scsi : 1 host.
Vendor: IBM Model: DDRS-39130W Rev: S92A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 6, lun 0
scsi0: Target 6: Queue Depth 28, Wide Synchronous at 40.0 MB/sec, offset
15
scsi : detected 1 SCSI disk total.
-------
When I boot 2.1.131, the scsi info gets to the line "scsi : 1 host." like
above, then after 15 or 20 seconds it comes up with a message about a
timeout, then resets the BT958 and times out again...continues to loop
like this.
Which settings in the config file should I be looking at?
Thanks,
Curt
----------
These are a few lines from the .config file for the 2.0.35 kernel:
----------
CONFIG_PCI=y
# CONFIG_PCI_OPTIMIZE is not set
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_BLK_DEV_IDE_PCMCIA is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_TRITON=y
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
# SCSI low-level drivers
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
# CONFIG_OVERRIDE_CMDS is not set
# CONFIG_AIC7XXX_PROC_STATS is not set
CONFIG_AIC7XXX_RESET_DELAY=15
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
CONFIG_SCSI_BUSLOGIC=y
---------------------
These are a few from the 2.1.131 .config:
---------------------
CONFIG_PCI=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_QUIRKS=y
# CONFIG_PCI_OPTIMIZE is not set
CONFIG_PCI_OLD_PROC=y
# CONFIG_MCA is not set
CONFIG_BLK_DEV_FD=y
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_BLK_DEV_IDECD=y
# CONFIG_BLK_DEV_IDETAPE is not set
# CONFIG_BLK_DEV_IDEFLOPPY is not set
# CONFIG_BLK_DEV_IDESCSI is not set
# CONFIG_BLK_DEV_CMD640 is not set
# CONFIG_BLK_DEV_RZ1000 is not set
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_NS87415 is not set
# CONFIG_BLK_DEV_VIA82C586 is not set
# CONFIG_BLK_DEV_CMD646 is not set
# CONFIG_IDE_CHIPSETS is not set
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_MD is not set
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_BLK_DEV_XD is not set
CONFIG_PARIDE_PARPORT=y
# CONFIG_PARIDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_ST=y
# CONFIG_BLK_DEV_SR is not set
# CONFIG_CHR_DEV_SG is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_AHA152X is not set
# CONFIG_SCSI_AHA1542 is not set
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=y
# CONFIG_OVERRIDE_CMDS is not set
# CONFIG_AIC7XXX_PROC_STATS is not set
CONFIG_AIC7XXX_RESET_DELAY=15
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
CONFIG_SCSI_BUSLOGIC=y
# CONFIG_SCSI_OMIT_FLASHPOINT is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
-
Linux SMP list: FIRST see FAQ at http://www.irisa.fr/prive/mentre/smp-faq/
To Unsubscribe: send "unsubscribe linux-smp" to [EMAIL PROTECTED]
