Fixed.
U-Boot SPL 2014.04 (Jun 28 2014 - 12:19:24)
Board: A20-SOM
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600
U-Boot 2014.04 (Jun 28 2014 - 12:19:24) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Board: A20-SOM
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Net: dwmac.1c50000
Hit any key to stop autoboot: 0
sun7i#
sun7i# ping 192.100.1.10
Speed: 100, full duplex
Using dwmac.1c50000 device
host 192.100.1.10 is alive
sun7i#
--- ./boards.cfg 2014-06-28 11:20:49.695132898 +0100
+++ ./boards.cfg 2014-06-28 11:23:27.311513187 +0100
@@ -383,6 +383,7 @@ Active arm armv7 sunxi
Active arm armv7 sunxi - sunxi
A13_MID sun5i:A13_MID,SPL,CONS_INDEX=2
-
Active arm armv7 sunxi - sunxi
A20-OLinuXino_MICRO
sun7i:A20_OLINUXINO_M,CONS_INDEX=1,STATUSLED=226,SPL,SUNXI_EMAC
-
Active arm armv7 sunxi - sunxi
A20-OLinuXino_MICRO_FEL
sun7i:A20_OLINUXINO_M,CONS_INDEX=1,STATUSLED=226,SPL_FEL,SUNXI_EMAC
-
+Active arm armv7 sunxi - sunxi
A20-SOM
sun7i:A20_SOM,SPL,SUNXI_GMAC,RGMII,STATUSLED1=245,FAST_MBUS
-
Active arm armv7 sunxi - sunxi
Auxtek-T003
sun5i:AUXTEK_T003,SPL,AXP152_POWER,STATUSLED=34
-
Active arm armv7 sunxi - sunxi
Auxtek-T004
sun5i:AUXTEK_T004,SPL,AXP152_POWER,STATUSLED=34
-
Active arm armv7 sunxi - sunxi
ba10_tv_box
sun4i:BA10_TV_BOX,SPL,SUNXI_EMAC
-
--- ./board/sunxi/Makefile 2014-06-28 12:14:20.554482957 +0100
+++ ./board/sunxi/Makefile 2014-06-28 12:16:38.838088151 +0100
@@ -17,6 +17,7 @@ obj-$(CONFIG_A13_OLINUXINO) += dram_a13_
obj-$(CONFIG_A13_OLINUXINOM) += dram_a13_oli_micro.o
obj-$(CONFIG_A13_MID) += dram_a13_mid.o
obj-$(CONFIG_A20_OLINUXINO_M) += dram_sun7i_384_1024_iow16.o
+obj-$(CONFIG_A20_SOM) += dram_sun7i_384_1024_iow16.o
obj-$(CONFIG_AUXTEK_T003) += dram_auxtek_t003.o
# This is not a typo, uses the same mem settings as the a10s-olinuxino-m
obj-$(CONFIG_AUXTEK_T004) += dram_a10s_olinuxino_m.o
On Fri, Jun 27, 2014 at 7:52 PM, bruce bushby <[email protected]>
wrote:
>
> sadly the a20-som and pcduino3 are sufficiently different that the
> Linksprit_pcDuino3 uboot image doesn't work :(
>
> U-Boot 2014.04 (Jun 27 2014 - 12:49:04) Allwinner Technology
>
> CPU: Allwinner A20 (SUN7I)
> Board: Linksprite_pcDuino3
> I2C: ready
> DRAM: 1 GiB
> MMC: SUNXI SD/MMC: 0
> In: serial
> Out: serial
> Err: serial
> Net: dwmac.1c50000
> Hit any key to stop autoboot: 0
> sun7i#
> sun7i# ping 192.100.1.10
> ping failed; host 192.100.1.10 is not alive
> sun7i#
>
>
>
>
>
>
>
> On Fri, Jun 27, 2014 at 1:23 PM, bruce bushby <[email protected]>
> wrote:
>
>> Hi Pillar
>>
>> I was only testing from uboot, I used ping and tftp.
>>
>> I can't thank you enough for your response, I'm going to try pcDuino3
>> uboot and uImage as soon as I get home and will post the results. I'm
>> hoping your use of GMAC resolves my issue.
>>
>>
>> Bruce
>>
>>
>>
>>
>> On Fri, Jun 27, 2014 at 10:32 AM, 左宝柱 <[email protected]> wrote:
>>
>>> pcDuinov3 uboot (running on A20-SOM) ethernet else working.
>>> U-Boot 2014.04-01537-g257ae94 (Jun 26 2014 - 11:12:14) Allwinner
>>> Technology
>>>
>>> CPU: Allwinner A20 (SUN7I)
>>> Board: Linksprite_pcDuino3
>>> I2C: ready
>>> DRAM: 1 GiB
>>> MMC: SUNXI SD/MMC: 0
>>> *** Warning - bad CRC, using default environment
>>>
>>> In: serial
>>> Out: serial
>>> Err: serial
>>> Net: dwmac.1c50000
>>> Hit any key to stop autoboot: 0
>>> reading uEnv.txt
>>> 322 bytes read in 16 ms (19.5 KiB/s)
>>> Loaded environment from uEnv.txt
>>> Running uenvcmd ...
>>> Speed: 100, full duplex
>>> BOOTP broadcast 1
>>> DHCP client bound to address 192.168.1.119
>>> Speed: 100, full duplex
>>> Using dwmac.1c50000 device
>>> TFTP from server 192.168.1.100; our IP address is 192.168.1.119
>>> Filename 'arch/arm/boot/uImage'.
>>> Load address: 0x46000000
>>> Loading:
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################################
>>> #################################################
>>> 340.8 KiB/s
>>> done
>>> Bytes transferred = 8351104 (7f6d80 hex)
>>> Speed: 100, full duplex
>>> Using dwmac.1c50000 device
>>> TFTP from server 192.168.1.100; our IP address is 192.168.1.119
>>> Filename 'arch/arm/boot/dts/sun7i-a20-pcduino3.dtb'.
>>> Load address: 0x49000000
>>> Loading: ##
>>> 294.9 KiB/s
>>> done
>>> Bytes transferred = 21183 (52bf hex)
>>> ## Booting kernel from Legacy Image at 46000000 ...
>>> Image Name: Linux-3.15.0-rc6-01550-g119918d-
>>> Image Type: ARM Linux Kernel Image (uncompressed)
>>> Data Size: 8351040 Bytes = 8 MiB
>>> Load Address: 40008000
>>> Entry Point: 40008000
>>> Verifying Checksum ... OK
>>> ## Flattened Device Tree blob at 49000000
>>> Booting using the fdt blob at 0x49000000
>>> Loading Kernel Image ... OK
>>> Using Device Tree in place at 49000000, end 490082be
>>>
>>> Starting kernel ...
>>>
>>> [ 0.000000] Booting Linux on physical CPU 0x0
>>>
>>>
>>> Do you test ethernet other way?
>>>
>>>
>>> Pillar
>>>
>>> --
>>> You received this message because you are subscribed to a topic in the
>>> Google Groups "linux-sunxi" group.
>>> To unsubscribe from this topic, visit
>>> https://groups.google.com/d/topic/linux-sunxi/nRXlsqemDt8/unsubscribe.
>>> To unsubscribe from this group and all its topics, send an email to
>>> [email protected].
>>> For more options, visit https://groups.google.com/d/optout.
>>>
>>
>>
>
--
You received this message because you are subscribed to the Google Groups
"linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
