This is a Q8 format 7 inch tablet with an Allwinner A13 SoC. It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera, RTL8188-based WiFi, and micro SD slot for external storage.
It is likely made by a subsidiary of Hanns.G (Hannstar). Signed-off-by: Chen-Yu Tsai <[email protected]> --- Added missing '>' to the email address in the header. Sorry for the noise. --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun5i-a13-hsg-h702.dts | 101 +++++++++++++++++++++++++++++++ 2 files changed, 102 insertions(+) create mode 100644 arch/arm/boot/dts/sun5i-a13-hsg-h702.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b8c5cd3..94e61a6 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -406,6 +406,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \ dtb-$(CONFIG_MACH_SUN5I) += \ sun5i-a10s-olinuxino-micro.dtb \ sun5i-a10s-r7-tv-dongle.dtb \ + sun5i-a13-hsg-h702.dtb \ sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino-micro.dtb dtb-$(CONFIG_MACH_SUN6I) += \ diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts new file mode 100644 index 0000000..6335c1e --- /dev/null +++ b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts @@ -0,0 +1,101 @@ +/* + * Copyright 2014 Chen-Yu Tsai <[email protected]> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun5i-a13.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "HSG H702"; + compatible = "hsg,h702", "allwinner,sun5i-a13"; + + soc@01c00000 { + mmc0: mmc@01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 6 0 0>; /* PG0 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + pinctrl@01c20800 { + mmc0_cd_pin_h702: mmc0_cd_pin@0 { + allwinner,pins = "PG0"; + allwinner,function = "gpio_in"; + allwinner,drive = <0>; + allwinner,pull = <1>; + }; + }; + + uart1: serial@01c28400 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins_b>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupts = <0>; + interrupt-controller; + #interrupt-cells = <1>; + }; + }; + + i2c1: i2c@01c2b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + + i2c2: i2c@01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; + }; + + reg_usb1_vbus: usb1-vbus { + /* + * There doesn't seem to be a GPIO for controlling + * vbus, despite the fex file saying otherwise. + * Override the original settings with empty ones. + */ + pinctrl-0 = <>; + gpio = <>; + status = "okay"; + }; +}; -- 2.1.0 -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
