On Mon, Sep 8, 2014 at 5:37 PM, Maxime Ripard <[email protected]> wrote: > Hi, > > On Mon, Sep 01, 2014 at 10:14:39PM +0800, Chen-Yu Tsai wrote: >> This is a Q8 format 7 inch tablet with an Allwinner A13 SoC. >> It has 512MB DRAM, 4GB NAND flash, an accelerometer, camera, >> RTL8188-based WiFi, and micro SD slot for external storage. >> >> It is likely made by a subsidiary of Hanns.G (Hannstar). >> >> Signed-off-by: Chen-Yu Tsai <[email protected]> >> --- >> >> Added missing '>' to the email address in the header. >> >> Sorry for the noise. >> >> --- >> arch/arm/boot/dts/Makefile | 1 + >> arch/arm/boot/dts/sun5i-a13-hsg-h702.dts | 101 >> +++++++++++++++++++++++++++++++ >> 2 files changed, 102 insertions(+) >> create mode 100644 arch/arm/boot/dts/sun5i-a13-hsg-h702.dts >> >> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile >> index b8c5cd3..94e61a6 100644 >> --- a/arch/arm/boot/dts/Makefile >> +++ b/arch/arm/boot/dts/Makefile >> @@ -406,6 +406,7 @@ dtb-$(CONFIG_MACH_SUN4I) += \ >> dtb-$(CONFIG_MACH_SUN5I) += \ >> sun5i-a10s-olinuxino-micro.dtb \ >> sun5i-a10s-r7-tv-dongle.dtb \ >> + sun5i-a13-hsg-h702.dtb \ >> sun5i-a13-olinuxino.dtb \ >> sun5i-a13-olinuxino-micro.dtb >> dtb-$(CONFIG_MACH_SUN6I) += \ >> diff --git a/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts >> b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts >> new file mode 100644 >> index 0000000..6335c1e >> --- /dev/null >> +++ b/arch/arm/boot/dts/sun5i-a13-hsg-h702.dts >> @@ -0,0 +1,101 @@ >> +/* >> + * Copyright 2014 Chen-Yu Tsai <[email protected]> >> + * >> + * The code contained herein is licensed under the GNU General Public >> + * License. You may obtain a copy of the GNU General Public License >> + * Version 2 or later at the following locations: > > Could you relicense the file to match the GPL/X11 dual license we've > been working on?
Sure. That's the plan. :) Waiting for that series to be merged before I send a new version. >> + * >> + * http://www.opensource.org/licenses/gpl-license.html >> + * http://www.gnu.org/copyleft/gpl.html >> + */ >> + >> +/dts-v1/; >> +/include/ "sun5i-a13.dtsi" >> +/include/ "sunxi-common-regulators.dtsi" >> + >> +/ { >> + model = "HSG H702"; >> + compatible = "hsg,h702", "allwinner,sun5i-a13"; >> + >> + soc@01c00000 { >> + mmc0: mmc@01c0f000 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_h702>; >> + vmmc-supply = <®_vcc3v3>; >> + bus-width = <4>; >> + cd-gpios = <&pio 6 0 0>; /* PG0 */ >> + cd-inverted; >> + status = "okay"; >> + }; >> + >> + usbphy: phy@01c13400 { >> + usb1_vbus-supply = <®_usb1_vbus>; >> + status = "okay"; >> + }; >> + >> + ehci0: usb@01c14000 { >> + status = "okay"; >> + }; >> + >> + ohci0: usb@01c14400 { >> + status = "okay"; >> + }; >> + >> + pinctrl@01c20800 { >> + mmc0_cd_pin_h702: mmc0_cd_pin@0 { >> + allwinner,pins = "PG0"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <0>; >> + allwinner,pull = <1>; >> + }; >> + }; >> + >> + uart1: serial@01c28400 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart1_pins_b>; >> + status = "okay"; >> + }; >> + >> + i2c0: i2c@01c2ac00 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c0_pins_a>; >> + status = "okay"; >> + >> + axp209: pmic@34 { >> + compatible = "x-powers,axp209"; >> + reg = <0x34>; >> + interrupts = <0>; >> + interrupt-controller; >> + #interrupt-cells = <1>; >> + }; >> + }; >> + >> + i2c1: i2c@01c2b000 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c1_pins_a>; >> + status = "okay"; >> + >> + pcf8563: rtc@51 { >> + compatible = "nxp,pcf8563"; >> + reg = <0x51>; >> + }; >> + }; >> + >> + i2c2: i2c@01c2b400 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c2_pins_a>; >> + status = "okay"; >> + }; >> + }; >> + >> + reg_usb1_vbus: usb1-vbus { >> + /* >> + * There doesn't seem to be a GPIO for controlling >> + * vbus, despite the fex file saying otherwise. >> + * Override the original settings with empty ones. >> + */ >> + pinctrl-0 = <>; >> + gpio = <>; >> + status = "okay"; > > Hmmmm, no. Just use a regular fixed regulator here, like reg_vcc3v3. Ok, will fix. Thanks ChenYu -- You received this message because you are subscribed to the Google Groups "linux-sunxi" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/d/optout.
