It's now working fine for me after a reboot. When I first did the update, I got impatient, and did a "sync". This yielded nothing, so I then kill -9ed it, which was, I admit, a little unfortunate. Didn't seem to work, but a bad idea all the same.
I've now managed things OK, and though I still get quite a lot of output to messages, none of it looks very scary: Jul 1 16:20:56 satsuma kernel: hub 1-0:0: debounce: port 2: delay 100ms stable 4 status 0x501 Jul 1 16:20:57 satsuma kernel: hub 2-0:0: debounce: port 2: delay 100ms stable 4 status 0x101 Jul 1 16:20:57 satsuma kernel: hub 2-0:0: new USB device on port 2, assigned address 3 Jul 1 16:20:57 satsuma kernel: usb-storage: This device (0451,5409) has unneeded SubClass and Protocol entries in unusual_devs.h Jul 1 16:20:57 satsuma kernel: Please send a copy of this message to <[EMAIL PROTECTED]> Jul 1 16:21:02 satsuma kernel: drivers/usb/core/message.c: usb_control/bulk_msg: timeout Jul 1 16:21:02 satsuma kernel: scsi2 : SCSI emulation for USB Mass Storage devices Jul 1 16:21:02 satsuma kernel: Vendor: NEUROS Model: dig. audio comp. Rev: 1.00 Jul 1 16:21:02 satsuma kernel: Type: Direct-Access ANSI SCSI revision: 02 Jul 1 16:21:02 satsuma kernel: SCSI device sda: 39070048 512-byte hdwr sectors (20004 MB) Jul 1 16:21:02 satsuma kernel: sda: test WP failed, assume Write Enabled Jul 1 16:21:02 satsuma kernel: SCSI error: host 2 id 0 lun 0 return code = 8000002 Jul 1 16:21:02 satsuma kernel: ^ISense class 7, sense error 0, extended sense 0 Jul 1 16:21:03 satsuma kernel: /dev/scsi/host2/bus0/target0/lun0: p1 Jul 1 16:21:03 satsuma kernel: SCSI error: host 2 id 0 lun 0 return code = 8000002 Jul 1 16:21:03 satsuma kernel: ^ISense class 7, sense error 0, extended sense 0 Jul 1 16:21:03 satsuma kernel: Attached scsi removable disk sda at scsi2, channel 0, id 0, lun 0 Jul 1 16:21:03 satsuma kernel: Attached scsi generic sg1 at scsi2, channel 0, id 0, lun 0, type 0 Jul 1 16:21:14 satsuma kernel: SCSI error: host 2 id 0 lun 0 return code = 8000002 Jul 1 16:21:14 satsuma kernel: ^ISense class 7, sense error 0, extended sense 0 On Tue, 2003-07-01 at 16:22, Alan Stern wrote: > Mike and Adam: > > It looks like you two are having similar problems with the same sort of > device. I just noticed that the vendor and product ID numbers you both > report are the same (0451,5409). Check out: > > http://sourceforge.net/mailarchive/forum.php?thread_id=2679481&forum_id=5398 > > and > > http://sourceforge.net/mailarchive/forum.php?thread_id=2693048&forum_id=5398 > > Maybe you can swap notes and see if you can figure anything out. > > Alan Stern -- Mike Bursell [EMAIL PROTECTED] +44 7050 144575
signature.asc
Description: This is a digitally signed message part
