> Note that I have the same problem here with my keyspan and mouse not
> working and paulus keyspan doesn't work. Actually, what happens is
> I plug the keyspan, it gets detected, d/l the firmware, disconnects,
> then nothing happens, khubd seems dead, plugging the mouse will not
> work. Not sure what's up, looks like disconnections are wrong.
>
> I'll check the patch you mentioned, it would be great to get a
> fix in ASAP for that
Ok, more data:
- the setconf-0325.patch doesn't help (all logs with that patch
applied)
- boot with no device. Plug mouse. Unplug mouse. USB dead, I
can't plug/unplug anything (looks like khubd is stuck)
- khubd backtrace is:
_switch
schedule
wait_for_completion
usb_disable_device
usb_disconnect
hub_port_connect_change
hub_event
hub_thread
kernel_thread
- log with debug enabled. I enclosed full dmesg after boot, after plugging
the mouse, after unplugging it, then after re-plugging it (no difference
with previous step).
Ben.
Total memory = 1024MB; using 2048kB for hash table (at c0600000)
Linux version 2.6.5-rc2-ben0 ([EMAIL PROTECTED]) (gcc version 3.3.3 (Debian 20040320))
#30 Fri Mar 26 13:54:11 EST 2004
Found UniNorth memory controller & host bridge, revision: 17
Mapped at 0xfdeb5000
Found a Keylargo mac-io controller, rev: 3, mapped at 0xfde35000
Processor NAP mode on idle enabled.
PowerMac motherboard: PowerBook Titanium IV
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 0c
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->1
nvram: Checking bank 0...
nvram: gen0=690, gen1=689
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 262144
DMA zone: 196608 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 65536 pages, LIFO batch:16
Built 1 zonelists
Kernel command line: root=/dev/hda13 ro pmdisk=/dev/hda14
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc5e3000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 4096 (order 12: 32768 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 33.331610 MHz
Console: colour dummy device 80x25
Memory: 1029248k available (3276k kernel code, 1452k data, 172k init, 262144k highmem)
System.map loaded at 0xc1a00000 for debugger, size: 917505 bytes
AGP special page: 0xeffff000
Calibrating delay loop... 665.60 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: Probing PCI hardware
Can't get bus-range for /[EMAIL PROTECTED]/[EMAIL PROTECTED]
Registering openpic with sysfs...
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon Lf DDR SGRAM 64 MB
Registering PowerMac CPU frequency driver
Low: 667 Mhz, High: 1000 Mhz, Boot: 667 Mhz, switch method: PMU
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
Console: switching to colour frame buffer device 160x53
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.98 8/24/03 David S. Miller ([EMAIL PROTECTED])
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:78:2c:9a
PHY ID: 2060e1, addr: 0
eth0: Found BCM5421 PHY
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MacIO PCI driver attached to Keylargo chipset
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
adb: starting probe task...
adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
Probing IDE interface ide0...
hda: FUJITSU MHS2060AT, ATA DISK drive
ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c
hda: Enabling Ultra DMA 4
Using anticipatory io scheduler
ide0 at 0xf2334000-0xf2334007,0xf2334160 on irq 19
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 20
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8121, ATAPI CD/DVD-ROM drive
hdc: MDMA, cycleTime: 120, accessTime: 90, recTime: 30
hdc: Set MDMA timing for mode 2, reg: 0x00011d26
hdc: Enabling MultiWord DMA 2
ide1 at 0xf2339000-0xf2339007,0xf2339160 on irq 20
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14
hda15 hda16
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mesh: configured for synchronous 5 MB/s
st: Version 20040318, fixed bufsize 32768, s/g segs 256
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0001:01:18.0 (0000 -> 0002)
ohci_hcd 0001:01:18.0: Apple Computer Inc. KeyLargo USB
ohci_hcd 0001:01:18.0: reset, control = 0xc0
ohci_hcd 0001:01:18.0: irq 27, pci mem f233e000
ohci_hcd 0001:01:18.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:01:18.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: Apple Computer Inc. KeyLargo USB
usb usb1: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb1: SerialNumber: 0001:01:18.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0001:01:18.0: created debug files
ohci_hcd 0001:01:18.0: OHCI controller state
ohci_hcd 0001:01:18.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:18.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:18.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:18.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:18.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:18.0: hcca frame #005a
ohci_hcd 0001:01:18.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:18.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:18.0: roothub.status 00000000
ohci_hcd 0001:01:18.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:18.0: roothub.portstatus [1] 0x00000100 PPS
PCI: Enabling device 0001:01:19.0 (0000 -> 0002)
ohci_hcd 0001:01:19.0: Apple Computer Inc. KeyLargo USB (#2)
ohci_hcd 0001:01:19.0: reset, control = 0xc0
ohci_hcd 0001:01:19.0: irq 28, pci mem f2340000
ohci_hcd 0001:01:19.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:19.0: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: Apple Computer Inc. KeyLargo USB (#2)
usb usb2: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb2: SerialNumber: 0001:01:19.0
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
ohci_hcd 0001:01:19.0: created debug files
ohci_hcd 0001:01:19.0: OHCI controller state
ohci_hcd 0001:01:19.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:19.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:19.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:19.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:19.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:19.0: hcca frame #005a
ohci_hcd 0001:01:19.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:19.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:19.0: roothub.status 00000000
ohci_hcd 0001:01:19.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:19.0: roothub.portstatus [1] 0x00000100 PPS
USB Universal Host Controller Interface driver v2.2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k init 4k chrp 8k prep
Adding 1048568k swap on /dev/hda14. Priority:-1 extents:1
EXT3 FS on hda13, internal journal
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth 1.5 chipset
agpgart: Maximum main memory to use for agp memory: 942M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
tas driver [TAS3004 driver V 0.3])
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
using i2c address: 0x35 from device-tree
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0001:01:1a.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ mask 0x0000, PCI irq 58
Socket status: 30000106
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffe782c9a]
ip1394: $Rev: 1175 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
PHY ID: 2060e1, addr: 0
eth0: Link is up at 1000 Mbps, full-duplex.
eth0: Pause is disabled
hda: Set PIO timing for mode 0, reg: 0x0c50032b
[drm] Initialized radeon 1.9.0 20020828 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
cdrom: This disc doesn't have any tracks I recognize!
Total memory = 1024MB; using 2048kB for hash table (at c0600000)
Linux version 2.6.5-rc2-ben0 ([EMAIL PROTECTED]) (gcc version 3.3.3 (Debian 20040320))
#30 Fri Mar 26 13:54:11 EST 2004
Found UniNorth memory controller & host bridge, revision: 17
Mapped at 0xfdeb5000
Found a Keylargo mac-io controller, rev: 3, mapped at 0xfde35000
Processor NAP mode on idle enabled.
PowerMac motherboard: PowerBook Titanium IV
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 0c
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->1
nvram: Checking bank 0...
nvram: gen0=690, gen1=689
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 262144
DMA zone: 196608 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 65536 pages, LIFO batch:16
Built 1 zonelists
Kernel command line: root=/dev/hda13 ro pmdisk=/dev/hda14
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc5e3000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 4096 (order 12: 32768 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 33.331610 MHz
Console: colour dummy device 80x25
Memory: 1029248k available (3276k kernel code, 1452k data, 172k init, 262144k highmem)
System.map loaded at 0xc1a00000 for debugger, size: 917505 bytes
AGP special page: 0xeffff000
Calibrating delay loop... 665.60 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: Probing PCI hardware
Can't get bus-range for /[EMAIL PROTECTED]/[EMAIL PROTECTED]
Registering openpic with sysfs...
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon Lf DDR SGRAM 64 MB
Registering PowerMac CPU frequency driver
Low: 667 Mhz, High: 1000 Mhz, Boot: 667 Mhz, switch method: PMU
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
Console: switching to colour frame buffer device 160x53
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.98 8/24/03 David S. Miller ([EMAIL PROTECTED])
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:78:2c:9a
PHY ID: 2060e1, addr: 0
eth0: Found BCM5421 PHY
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MacIO PCI driver attached to Keylargo chipset
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
adb: starting probe task...
adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
Probing IDE interface ide0...
hda: FUJITSU MHS2060AT, ATA DISK drive
ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c
hda: Enabling Ultra DMA 4
Using anticipatory io scheduler
ide0 at 0xf2334000-0xf2334007,0xf2334160 on irq 19
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 20
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8121, ATAPI CD/DVD-ROM drive
hdc: MDMA, cycleTime: 120, accessTime: 90, recTime: 30
hdc: Set MDMA timing for mode 2, reg: 0x00011d26
hdc: Enabling MultiWord DMA 2
ide1 at 0xf2339000-0xf2339007,0xf2339160 on irq 20
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14
hda15 hda16
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mesh: configured for synchronous 5 MB/s
st: Version 20040318, fixed bufsize 32768, s/g segs 256
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0001:01:18.0 (0000 -> 0002)
ohci_hcd 0001:01:18.0: Apple Computer Inc. KeyLargo USB
ohci_hcd 0001:01:18.0: reset, control = 0xc0
ohci_hcd 0001:01:18.0: irq 27, pci mem f233e000
ohci_hcd 0001:01:18.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:01:18.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: Apple Computer Inc. KeyLargo USB
usb usb1: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb1: SerialNumber: 0001:01:18.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0001:01:18.0: created debug files
ohci_hcd 0001:01:18.0: OHCI controller state
ohci_hcd 0001:01:18.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:18.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:18.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:18.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:18.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:18.0: hcca frame #005a
ohci_hcd 0001:01:18.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:18.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:18.0: roothub.status 00000000
ohci_hcd 0001:01:18.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:18.0: roothub.portstatus [1] 0x00000100 PPS
PCI: Enabling device 0001:01:19.0 (0000 -> 0002)
ohci_hcd 0001:01:19.0: Apple Computer Inc. KeyLargo USB (#2)
ohci_hcd 0001:01:19.0: reset, control = 0xc0
ohci_hcd 0001:01:19.0: irq 28, pci mem f2340000
ohci_hcd 0001:01:19.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:19.0: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: Apple Computer Inc. KeyLargo USB (#2)
usb usb2: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb2: SerialNumber: 0001:01:19.0
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
ohci_hcd 0001:01:19.0: created debug files
ohci_hcd 0001:01:19.0: OHCI controller state
ohci_hcd 0001:01:19.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:19.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:19.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:19.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:19.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:19.0: hcca frame #005a
ohci_hcd 0001:01:19.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:19.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:19.0: roothub.status 00000000
ohci_hcd 0001:01:19.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:19.0: roothub.portstatus [1] 0x00000100 PPS
USB Universal Host Controller Interface driver v2.2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k init 4k chrp 8k prep
Adding 1048568k swap on /dev/hda14. Priority:-1 extents:1
EXT3 FS on hda13, internal journal
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth 1.5 chipset
agpgart: Maximum main memory to use for agp memory: 942M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
tas driver [TAS3004 driver V 0.3])
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
using i2c address: 0x35 from device-tree
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0001:01:1a.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ mask 0x0000, PCI irq 58
Socket status: 30000106
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffe782c9a]
ip1394: $Rev: 1175 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
PHY ID: 2060e1, addr: 0
eth0: Link is up at 1000 Mbps, full-duplex.
eth0: Pause is disabled
hda: Set PIO timing for mode 0, reg: 0x0c50032b
[drm] Initialized radeon 1.9.0 20020828 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
cdrom: This disc doesn't have any tracks I recognize!
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES
CCS
usb 1-1: new low speed USB device using address 2
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hid 1-1:1.0: usb_probe_interface
hid 1-1:1.0: usb_probe_interface - got id
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.00 Mouse [04b3:3107] on usb-0001:01:18.0-1
Total memory = 1024MB; using 2048kB for hash table (at c0600000)
Linux version 2.6.5-rc2-ben0 ([EMAIL PROTECTED]) (gcc version 3.3.3 (Debian 20040320))
#30 Fri Mar 26 13:54:11 EST 2004
Found UniNorth memory controller & host bridge, revision: 17
Mapped at 0xfdeb5000
Found a Keylargo mac-io controller, rev: 3, mapped at 0xfde35000
Processor NAP mode on idle enabled.
PowerMac motherboard: PowerBook Titanium IV
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 0c
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->1
nvram: Checking bank 0...
nvram: gen0=690, gen1=689
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 262144
DMA zone: 196608 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 65536 pages, LIFO batch:16
Built 1 zonelists
Kernel command line: root=/dev/hda13 ro pmdisk=/dev/hda14
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc5e3000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 4096 (order 12: 32768 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 33.331610 MHz
Console: colour dummy device 80x25
Memory: 1029248k available (3276k kernel code, 1452k data, 172k init, 262144k highmem)
System.map loaded at 0xc1a00000 for debugger, size: 917505 bytes
AGP special page: 0xeffff000
Calibrating delay loop... 665.60 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: Probing PCI hardware
Can't get bus-range for /[EMAIL PROTECTED]/[EMAIL PROTECTED]
Registering openpic with sysfs...
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon Lf DDR SGRAM 64 MB
Registering PowerMac CPU frequency driver
Low: 667 Mhz, High: 1000 Mhz, Boot: 667 Mhz, switch method: PMU
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
Console: switching to colour frame buffer device 160x53
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.98 8/24/03 David S. Miller ([EMAIL PROTECTED])
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:78:2c:9a
PHY ID: 2060e1, addr: 0
eth0: Found BCM5421 PHY
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MacIO PCI driver attached to Keylargo chipset
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
adb: starting probe task...
adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
Probing IDE interface ide0...
hda: FUJITSU MHS2060AT, ATA DISK drive
ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c
hda: Enabling Ultra DMA 4
Using anticipatory io scheduler
ide0 at 0xf2334000-0xf2334007,0xf2334160 on irq 19
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 20
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8121, ATAPI CD/DVD-ROM drive
hdc: MDMA, cycleTime: 120, accessTime: 90, recTime: 30
hdc: Set MDMA timing for mode 2, reg: 0x00011d26
hdc: Enabling MultiWord DMA 2
ide1 at 0xf2339000-0xf2339007,0xf2339160 on irq 20
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14
hda15 hda16
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mesh: configured for synchronous 5 MB/s
st: Version 20040318, fixed bufsize 32768, s/g segs 256
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0001:01:18.0 (0000 -> 0002)
ohci_hcd 0001:01:18.0: Apple Computer Inc. KeyLargo USB
ohci_hcd 0001:01:18.0: reset, control = 0xc0
ohci_hcd 0001:01:18.0: irq 27, pci mem f233e000
ohci_hcd 0001:01:18.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:01:18.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: Apple Computer Inc. KeyLargo USB
usb usb1: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb1: SerialNumber: 0001:01:18.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0001:01:18.0: created debug files
ohci_hcd 0001:01:18.0: OHCI controller state
ohci_hcd 0001:01:18.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:18.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:18.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:18.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:18.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:18.0: hcca frame #005a
ohci_hcd 0001:01:18.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:18.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:18.0: roothub.status 00000000
ohci_hcd 0001:01:18.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:18.0: roothub.portstatus [1] 0x00000100 PPS
PCI: Enabling device 0001:01:19.0 (0000 -> 0002)
ohci_hcd 0001:01:19.0: Apple Computer Inc. KeyLargo USB (#2)
ohci_hcd 0001:01:19.0: reset, control = 0xc0
ohci_hcd 0001:01:19.0: irq 28, pci mem f2340000
ohci_hcd 0001:01:19.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:19.0: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: Apple Computer Inc. KeyLargo USB (#2)
usb usb2: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb2: SerialNumber: 0001:01:19.0
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
ohci_hcd 0001:01:19.0: created debug files
ohci_hcd 0001:01:19.0: OHCI controller state
ohci_hcd 0001:01:19.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:19.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:19.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:19.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:19.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:19.0: hcca frame #005a
ohci_hcd 0001:01:19.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:19.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:19.0: roothub.status 00000000
ohci_hcd 0001:01:19.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:19.0: roothub.portstatus [1] 0x00000100 PPS
USB Universal Host Controller Interface driver v2.2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k init 4k chrp 8k prep
Adding 1048568k swap on /dev/hda14. Priority:-1 extents:1
EXT3 FS on hda13, internal journal
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth 1.5 chipset
agpgart: Maximum main memory to use for agp memory: 942M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
tas driver [TAS3004 driver V 0.3])
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
using i2c address: 0x35 from device-tree
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0001:01:1a.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ mask 0x0000, PCI irq 58
Socket status: 30000106
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffe782c9a]
ip1394: $Rev: 1175 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
PHY ID: 2060e1, addr: 0
eth0: Link is up at 1000 Mbps, full-duplex.
eth0: Pause is disabled
hda: Set PIO timing for mode 0, reg: 0x0c50032b
[drm] Initialized radeon 1.9.0 20020828 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
cdrom: This disc doesn't have any tracks I recognize!
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES
CCS
usb 1-1: new low speed USB device using address 2
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hid 1-1:1.0: usb_probe_interface
hid 1-1:1.0: usb_probe_interface - got id
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.00 Mouse [04b3:3107] on usb-0001:01:18.0-1
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 1, status 100, change 3, 12 Mb/s
usb 1-1: USB disconnect, address 2
usb 1-1: usb_disable_device nuking all URBs
ohci_hcd 0001:01:18.0: shutdown urb edc430a4 pipe 40408280 ep1in-intr
usb 1-1: unregistering interface 1-1:1.0
drivers/usb/core/usb.c: usb_hotplug
Total memory = 1024MB; using 2048kB for hash table (at c0600000)
Linux version 2.6.5-rc2-ben0 ([EMAIL PROTECTED]) (gcc version 3.3.3 (Debian 20040320))
#30 Fri Mar 26 13:54:11 EST 2004
Found UniNorth memory controller & host bridge, revision: 17
Mapped at 0xfdeb5000
Found a Keylargo mac-io controller, rev: 3, mapped at 0xfde35000
Processor NAP mode on idle enabled.
PowerMac motherboard: PowerBook Titanium IV
via-pmu: Server Mode is disabled
PMU driver 2 initialized for Core99, firmware: 0c
Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->1
Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->1
nvram: Checking bank 0...
nvram: gen0=690, gen1=689
nvram: Active bank is: 0
nvram: OF partition at 0x410
nvram: XP partition at 0x1020
nvram: NR partition at 0x1120
On node 0 totalpages: 262144
DMA zone: 196608 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 65536 pages, LIFO batch:16
Built 1 zonelists
Kernel command line: root=/dev/hda13 ro pmdisk=/dev/hda14
PowerMac using OpenPIC irq controller at 0x80040000
OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc5e3000
OpenPIC timer frequency is 4.166666 MHz
PID hash table entries: 4096 (order 12: 32768 bytes)
GMT Delta read from XPRAM: 0 minutes, DST: off
time_init: decrementer frequency = 33.331610 MHz
Console: colour dummy device 80x25
Memory: 1029248k available (3276k kernel code, 1452k data, 172k init, 262144k highmem)
System.map loaded at 0xc1a00000 for debugger, size: 917505 bytes
AGP special page: 0xeffff000
Calibrating delay loop... 665.60 BogoMIPS
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
POSIX conformance testing by UNIFIX
NET: Registered protocol family 16
PCI: Probing PCI hardware
Can't get bus-range for /[EMAIL PROTECTED]/[EMAIL PROTECTED]
Registering openpic with sysfs...
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
PCI: Enabling device 0000:00:10.0 (0086 -> 0087)
radeonfb: Invalid ROM signature 0 should be 0xaa55
radeonfb: Retreived PLL infos from Open Firmware
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=200.00 MHz
radeonfb: Monitor 1 type LCD found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
radeonfb: Power Management enabled for Mobility chipsets
Registered "ati" backlight controller, level: 15/15
radeonfb: ATI Radeon Lf DDR SGRAM 64 MB
Registering PowerMac CPU frequency driver
Low: 667 Mhz, High: 1000 Mhz, Boot: 667 Mhz, switch method: PMU
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]).
Console: switching to colour frame buffer device 160x53
Generic RTC Driver v1.07
Macintosh non-volatile memory driver v1.1
pmac_zilog: 0.6 (Benjamin Herrenschmidt <[EMAIL PROTECTED]>)
ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port
ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
sungem.c:v0.98 8/24/03 David S. Miller ([EMAIL PROTECTED])
eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:78:2c:9a
PHY ID: 2060e1, addr: 0
eth0: Found BCM5421 PHY
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MacIO PCI driver attached to Keylargo chipset
input: Macintosh mouse button emulation
apm_emu: APM Emulation 0.5 initialized.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
adb: starting probe task...
adb devices: [2]: 2 c4 [3]: 3 1 [7]: 7 1f
ADB keyboard at 2, handler 1
Detected ADB keyboard, type ISO, swapping keys.
input: ADB keyboard on adb2:2.c4/input
input: ADB Powerbook buttons on adb7:7.1f/input
ADB mouse at 3, handler set to 4 (trackpad)
input: ADB mouse on adb3:3.01/input
adb: finished probe task...
ide0: Found Apple KeyLargo ATA-4 controller, bus ID 2, irq 19
Probing IDE interface ide0...
hda: FUJITSU MHS2060AT, ATA DISK drive
ide_pmac: Set UDMA timing for mode 4, reg: 0x0c50038c
hda: Enabling Ultra DMA 4
Using anticipatory io scheduler
ide0 at 0xf2334000-0xf2334007,0xf2334160 on irq 19
ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 20
Probing IDE interface ide1...
hdc: MATSHITACD-RW CW-8121, ATAPI CD/DVD-ROM drive
hdc: MDMA, cycleTime: 120, accessTime: 90, recTime: 30
hdc: Set MDMA timing for mode 2, reg: 0x00011d26
hdc: Enabling MultiWord DMA 2
ide1 at 0xf2339000-0xf2339007,0xf2339160 on irq 20
hda: max request size: 1024KiB
hda: 117210240 sectors (60011 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(66)
hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14
hda15 hda16
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
mesh: configured for synchronous 5 MB/s
st: Version 20040318, fixed bufsize 32768, s/g segs 256
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0001:01:18.0 (0000 -> 0002)
ohci_hcd 0001:01:18.0: Apple Computer Inc. KeyLargo USB
ohci_hcd 0001:01:18.0: reset, control = 0xc0
ohci_hcd 0001:01:18.0: irq 27, pci mem f233e000
ohci_hcd 0001:01:18.0: new USB bus registered, assigned bus number 1
ohci_hcd 0001:01:18.0: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: Apple Computer Inc. KeyLargo USB
usb usb1: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb1: SerialNumber: 0001:01:18.0
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: unknown reserved power switching mode
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
ohci_hcd 0001:01:18.0: created debug files
ohci_hcd 0001:01:18.0: OHCI controller state
ohci_hcd 0001:01:18.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:18.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:18.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:18.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:18.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:18.0: hcca frame #005a
ohci_hcd 0001:01:18.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:18.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:18.0: roothub.status 00000000
ohci_hcd 0001:01:18.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:18.0: roothub.portstatus [1] 0x00000100 PPS
PCI: Enabling device 0001:01:19.0 (0000 -> 0002)
ohci_hcd 0001:01:19.0: Apple Computer Inc. KeyLargo USB (#2)
ohci_hcd 0001:01:19.0: reset, control = 0xc0
ohci_hcd 0001:01:19.0: irq 28, pci mem f2340000
ohci_hcd 0001:01:19.0: new USB bus registered, assigned bus number 2
ohci_hcd 0001:01:19.0: root hub device address 1
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb2: Product: Apple Computer Inc. KeyLargo USB (#2)
usb usb2: Manufacturer: Linux 2.6.5-rc2-ben0 ohci_hcd
usb usb2: SerialNumber: 0001:01:19.0
drivers/usb/core/usb.c: usb_hotplug
usb usb2: registering 2-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: unknown reserved power switching mode
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: Port indicators are not supported
hub 2-0:1.0: power on to power good time: 20ms
hub 2-0:1.0: hub controller current requirement: 0mA
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
hub 2-0:1.0: enabling power on all ports
ohci_hcd 0001:01:19.0: created debug files
ohci_hcd 0001:01:19.0: OHCI controller state
ohci_hcd 0001:01:19.0: OHCI 1.0, with legacy support registers
ohci_hcd 0001:01:19.0: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0001:01:19.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0001:01:19.0: intrstatus 0x00000044 RHSC SF
ohci_hcd 0001:01:19.0: intrenable 0x80000012 MIE UE WDH
ohci_hcd 0001:01:19.0: hcca frame #005a
ohci_hcd 0001:01:19.0: roothub.a 0a000202 POTPGT=10 NPS NDP=2
ohci_hcd 0001:01:19.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0001:01:19.0: roothub.status 00000000
ohci_hcd 0001:01:19.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0001:01:19.0: roothub.portstatus [1] 0x00000100 PPS
USB Universal Host Controller Interface driver v2.2
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 37449)
NET: Registered protocol family 1
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 172k init 4k chrp 8k prep
Adding 1048568k swap on /dev/hda14. Priority:-1 extents:1
EXT3 FS on hda13, internal journal
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected Apple UniNorth 1.5 chipset
agpgart: Maximum main memory to use for agp memory: 942M
agpgart: configuring for size idx: 4
agpgart: AGP aperture is 16M @ 0x0
tas driver [TAS3004 driver V 0.3])
Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
using i2c address: 0x35 from device-tree
Audio jack unplugged, enabling speakers.
AE-Init snapper mixer
PowerMac Snapper DMA sound driver rev 016 installed
Core driver edition 01.06 : PowerMac Built-in Sound driver edition 00.07
Write will use 4 fragments of 32768 bytes as default
Read will use 4 fragments of 32768 bytes as default
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda12, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda16, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0001:01:1a.0 [0000:0000]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta: ISA IRQ mask 0x0000, PCI irq 58
Socket status: 30000106
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1172 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394: fw-host0: Unexpected PCI resource length of 1000!
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[f5000000-f50007ff] Max
Packet=[2048]
ieee1394: Host added: ID:BUS[0-00:1023] GUID[000a95fffe782c9a]
ip1394: $Rev: 1175 $ Ben Collins <[EMAIL PROTECTED]>
ip1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
PHY ID: 2060e1, addr: 0
eth0: Link is up at 1000 Mbps, full-duplex.
eth0: Pause is disabled
hda: Set PIO timing for mode 0, reg: 0x0c50032b
[drm] Initialized radeon 1.9.0 20020828 on minor 0
agpgart: Putting AGP V2 device at 0000:00:0b.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:00:10.0 into 4x mode
[drm] Loading R200 Microcode
cdrom: This disc doesn't have any tracks I recognize!
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES
CCS
usb 1-1: new low speed USB device using address 2
usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hid 1-1:1.0: usb_probe_interface
hid 1-1:1.0: usb_probe_interface - got id
drivers/usb/input/hid-core.c: ctrl urb status -32 received
input: USB HID v1.00 Mouse [04b3:3107] on usb-0001:01:18.0-1
ohci_hcd 0001:01:18.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC CSC PPS
hub 1-0:1.0: port 1, status 100, change 3, 12 Mb/s
usb 1-1: USB disconnect, address 2
usb 1-1: usb_disable_device nuking all URBs
ohci_hcd 0001:01:18.0: shutdown urb edc430a4 pipe 40408280 ep1in-intr
usb 1-1: unregistering interface 1-1:1.0
drivers/usb/core/usb.c: usb_hotplug
