On Fri, May 28, 2004 at 03:31:47PM -0700, David Brownell wrote:
>
> With 2.6.7-rc1, compiled with CONFIG_USB_DEBUG, and assuming EHCI
> is "usb1", what happens when you do this:
>
> cd /sys/class/usb_host/usb1
I recompiled what I had on hands, i.e. sources from Arjan, with
CONFIG_USB_DEBUG. The only 'registers' which showed up in /sys
were in /sys/class/usb_host/usb4 so I guess that this will be EHCI
> cat registers
bus pci device 0000:00:1d.7
EHCI 1.00, hcd state 1 (driver 2003-Dec-29)
structural params 0x00103206
capability params 0x00006871
status 000c FLR PCD
command 010001 (park)=0 ithresh=1 period=1024 RUN
intrenable 33 IAA FATAL ERR INT
uframe 1d68
port 0 status 001000 POWER sig=se0
port 1 status 001000 POWER sig=se0
port 2 status 003002 POWER OWNER sig=se0 CSC
port 3 status 001000 POWER sig=se0
port 4 status 001000 POWER sig=se0
port 5 status 001000 POWER sig=se0
irq normal 0 err 0 reclaim 0 (lost 0)
complete 0 unlink 0
> echo -n 3 > device/power/state
> cat device/power/state
3
> echo -n 0 > device/power/state
> cat device/power/state
0
> cat registers
bus pci device 0000:00:1d.7
EHCI 1.00, hcd state 1 (driver 2003-Dec-29)
structural params 0x00103206
capability params 0x00006871
status 1004 Halt PCD
command 080000 (park)=0 ithresh=8 period=1024 HALT
intrenable 00
uframe 0000
port 0 status 001000 POWER sig=se0
port 1 status 001000 POWER sig=se0
port 2 status 003002 POWER OWNER sig=se0 CSC
port 3 status 001000 POWER sig=se0
port 4 status 001000 POWER sig=se0
port 5 status 001000 POWER sig=se0
irq normal 0 err 0 reclaim 0 (lost 0)
complete 0 unlink 0
> dmesg
Attached. BTW - three USB hubs are reported but there are only
two USB sockets on a laptop body. One is connected to what lsusb
calls "Bus 001" and another on "Bus 002".
> "lspci -vv" info for your system before and after resume might be
> interesting ... or more specifically, any differences between the
> two.
There are none. I tried just after reboot, after switching states
like the above and after an actual suspend/resume cycle. An output
of "lspci -vv" always looks the same. I am attaching a sample too.
Thanks,
Michal
ry: 247752k/253312k available (1548k kernel code, 4856k reserved, 603k data, 148k
init, 0k highmem)
Calibrating delay loop... 3948.54 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU: Intel Mobile Intel(R) Celeron(R) CPU 2.00GHz stepping 07
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 186k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd824, last bus=2
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: IRQ9 SCI: Edge set to Level Trigger.
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: Embedded Controller [EC] (gpe 28)
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs 10) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *11)
Linux Plug and Play Support v0.97 (c) Adam Belay
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: Using ACPI for IRQ routing
vesafb: probe of vesafb0 failed with error -6
Simple Boot Flag at 0x36 set to 0x1
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU] (supports C1 C2 C3, 8 throttling states)
ACPI: Thermal Zone [THM0] (49 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Maximum main memory to use for agp memory: 196M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xd8000000
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N030ATCS04-0, ATA DISK drive
Using cfq io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: QSI CD-RW/DVD-ROM SBW-242, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/1768KiB Cache, CHS=58140/16/63, UDMA(100)
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
Synaptics Touchpad, model: 1
Firmware: 4.6
180 degree mounted touchpad
Sensor: 18
new absolute packet format
Touchpad has extended capability bits
-> four buttons
-> multifinger detection
-> palm detection
input: SynPS/2 Synaptics TouchPad on isa0060/serio4
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S3 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 148k freed
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Sleep Button (CM) [SLPB]
USB Universal Host Controller Interface driver v2.2
uhci_hcd 0000:00:1d.0: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 10, io base 00001800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: detected 2 ports
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.6-1.394 uhci_hcd
usb usb1: SerialNumber: 0000:00:1d.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
uhci_hcd 0000:00:1d.1: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 11, io base 00001820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.6-1.394 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.1
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:1d.1: port 1 portsc 01a3
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
uhci_hcd 0000:00:1d.2: UHCI Host Controller
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: irq 11, io base 00001840
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: detected 2 ports
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: default language 0x0409
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.6-1.394 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.2
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
usb 2-1: new low speed USB device using address 2
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6
ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr
ehci_hcd 0000:00:1d.7: capability 0001 at 68
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 11, pci mem 120a4000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: reset command 080022 (park)=0 ithresh=8 Async period=1024 Reset
HALT
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: default language 0x0409
usb usb4: Product: EHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.6-1.394 ehci_hcd
usb usb4: SerialNumber: 0000:00:1d.7
usb usb4: hotplug
usb usb4: adding 4-0:1.0 (config #1, interface 0)
usb 4-0:1.0: hotplug
hub 4-0:1.0: usb_probe_interface
hub 4-0:1.0: usb_probe_interface - got id
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
hub 4-0:1.0: standalone hub
hub 4-0:1.0: ganged power switching
hub 4-0:1.0: individual port over-current protection
hub 4-0:1.0: Single TT
hub 4-0:1.0: TT requires at most 8 FS bit times
hub 4-0:1.0: power on to power good time: 20ms
hub 4-0:1.0: local power source is good
hub 4-0:1.0: enabling power on all ports
uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[10679240] link (0e6791b2) element (0ed52040)
0: [10d52040] link (0ed52080) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=2, PID=2d(SETUP) (buf=0e43ee88)
1: [10d52080] link (0ed520c0) e3 SPD LS Active Length=0 MaxLen=7 DT1 EndPt=0 Dev=2,
PID=69(IN) (buf=0e43eee8)
2: [10d520c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=2, PID=e1(OUT) (buf=00000000)
uhci_hcd 0000:00:1d.0: suspend_hc
uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[10679240] link (0e6791b2) element (0ed52040)
0: [10d52040] link (0ed52080) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=0, PID=2d(SETUP) (buf=0e43e248)
1: [10d52080] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=0, PID=69(IN) (buf=00000000)
uhci_hcd 0000:00:1d.1: uhci_result_control: failed with status 440000
[10679240] link (0e6791b2) element (0ed52040)
0: [10d52040] link (0ed52080) e0 LS Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0
Dev=0, PID=2d(SETUP) (buf=0e43e2e8)
1: [10d52080] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0
Dev=0, PID=69(IN) (buf=00000000)
usb 2-1: device not accepting address 2, error -71
uhci_hcd 0000:00:1d.2: suspend_hc
uhci_hcd 0000:00:1d.1: suspend_hc
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001403 POWER sig=k CSC CONNECT
hub 4-0:1.0: port 3, status 0501, change 0001, 480 Mb/s
hub 4-0:1.0: debounce: port 3: delay 100ms stable 4 status 0x501
ehci_hcd 0000:00:1d.7: port 3 low speed --> companion
ehci_hcd 0000:00:1d.7: GetStatus port 3 status 003002 POWER OWNER sig=se0 CSC
uhci_hcd 0000:00:1d.1: port 1 portsc 0183
hub 2-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
uhci_hcd 0000:00:1d.1: wakeup_hc
EXT3 FS on hda3, internal journal
hub 2-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
device-mapper: 4.1.0-ioctl (2003-12-10) initialised: [EMAIL PROTECTED]
usb 2-1: new low speed USB device using address 3
usb 2-1: skipped 1 descriptor after interface
usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: default language 0x0409
Adding 506008k swap on /dev/hda1. Priority:-1 extents:1
usb 2-1: Product: USB-PS/2 Optical Mouse
usb 2-1: Manufacturer: Logitech
usb 2-1: hotplug
usb 2-1: adding 2-1:1.0 (config #1, interface 0)
usb 2-1:1.0: hotplug
usbhid 2-1:1.0: usb_probe_interface
usbhid 2-1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:1d.1-1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.13 <[EMAIL PROTECTED]>
microcode: No new microdata for cpu 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
SCSI subsystem initialized
inserting floppy driver for 2.6.6-1.394
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
8139too Fast Ethernet driver 0.9.27
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0x3000, 00:00:e2:9c:35:14, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.27
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 at 0x3000, 00:00:e2:9c:35:14, IRQ 11
eth0: Identified 8139 chip type 'RTL-8100B/8139D'
eth0: link up, 10Mbps, half-duplex, lpa 0x0000
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
Yenta: CardBus bridge found at 0000:02:09.0 [17c0:3102]
Yenta: ISA IRQ mask 0x00b8, PCI irq 10
Socket status: 30000007
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
[drm] Initialized i830 1.3.2 20021108 on minor 0:
mtrr: base(0xd8020000) is not aligned on a size(0x300000) boundary
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49336 usecs
intel8x0: clocking to 48000
ehci_hcd 0000:00:1d.7: suspend D0 --> D3
ehci_hcd 0000:00:1d.7: suspend to 3
ehci_hcd 0000:00:1d.7: resume from state D3
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: resume
00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub
Interface (rev 03)
Subsystem: Wistron Corp.: Unknown device 2056
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable)
Capabilities: [e4] #09 [1105]
00:02.0 VGA compatible controller: Intel Corp. 82845G/GL[Brookdale-G]/GE Chipset
Integrated Graphics Device (rev 03) (prog-if 00 [VGA])
Subsystem: Wistron Corp.: Unknown device 2056
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d8000000 (32-bit, prefetchable)
Region 1: Memory at d0000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [d0] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1d.0 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #1 (rev 02) (prog-if 00
[UHCI])
Subsystem: Wistron Corp.: Unknown device 4002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1800 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #2 (rev 02) (prog-if 00
[UHCI])
Subsystem: Wistron Corp.: Unknown device 4002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801DB (ICH4) USB UHCI #3 (rev 02) (prog-if 00
[UHCI])
Subsystem: Wistron Corp.: Unknown device 4002
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 11
Region 4: I/O ports at 1840 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller (rev 02)
(prog-if 20 [EHCI])
Subsystem: Wistron Corp.: Unknown device 1071
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 0: Memory at d0080000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [2080]
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB/ER Hub interface to PCI Bridge (rev
82) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d0100000-d01fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801DB (ICH4) LPC Bridge (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801DB (ICH4) Ultra ATA 100 Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Wistron Corp.: Unknown device 4002
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 1860 [size=16]
Region 5: Memory at 10000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801DB/DBM (ICH4) SMBus Controller (rev 02)
Subsystem: Wistron Corp.: Unknown device 4002
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 1880 [size=32]
00:1f.5 Multimedia audio controller: Intel Corp. 82801DB (ICH4) AC'97 Audio Controller
(rev 02)
Subsystem: Wistron Corp.: Unknown device 2005
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 1c00
Region 1: I/O ports at 18c0 [size=64]
Region 2: Memory at d0080c00 (32-bit, non-prefetchable) [size=512]
Region 3: Memory at d0080800 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1f.6 Modem: Intel Corp. 82801DB (ICH4) AC'97 Modem Controller (rev 02) (prog-if 00
[Generic])
Subsystem: Wistron Corp.: Unknown device 1069
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 2400
Region 1: I/O ports at 2000 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+
(rev 10)
Subsystem: Wistron Corp.: Unknown device 1053
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 3000
Region 1: Memory at d0100000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:09.0 CardBus bridge: O2 Micro, Inc. OZ6912 Cardbus Controller
Subsystem: Wistron Corp.: Unknown device 3102
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10001000 (32-bit, non-prefetchable)
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
