Hi,
I have a sweex usb-wifi stick see also http://sourceforge.net/projects/linux-lc100020/ and it's forums.
And I have 2 machines
Machine 1: Via kt133a chipset -> uhci_hcd
Machine 2: Sis 748 Chipset -> ohci_hcd
The device works without a problem on machine 2 with at least kernels 2.6.6 and 2.6.7.
The usb wifi stick fails to accept an address on machine 1. There is a good faq about it with things you can try. (turn off acpi, irq for usb, no irq sharing, removing all pci cards,etc) I tried everything but with no luck.
I tried kernels 2.4.26 till and including 2.6.7 without luck, however on the same machine is also connected an usb joystick that works without a problem, so my usb does work.
The usb wifi stick is known to need to get a descriptor before settings it's address but even with this patch I can't get it to work ( I didn't need the patch for machine 2).
I read some usb specs/docs kernel usb stuff, but since I'm no expert I cannot see where the problem is, therefore posted below is some information that hopefully is helpfull to you.
Please let me know what else I can do to help,
Tommy
Dmesg output:
uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: detected 2 ports
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb1: Manufacturer: Linux 2.6.7 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
PCI: Found IRQ 10 for device 0000:00:07.3
PCI: Sharing IRQ 10 with 0000:00:07.2
PCI: Sharing IRQ 10 with 0000:00:0d.0
PCI: Sharing IRQ 10 with 0000:00:0b.0
uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:07.3: irq 10, io base 0000d800
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: detected 2 ports
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb2: Manufacturer: Linux 2.6.7 uhci_hcd
usb usb2: SerialNumber: 0000:00:07.3
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (cuhci_hcd 0000:00:07.2: port 1 portsc 01ab
hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
uhci_hcd 0000:00:07.2: port 1 portsc 01a9
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
usb 1-1: new low speed USB device using address 2
usb 1-1: skipped 1 descriptor after interface
usb 1-1: new device strings: Mfr=4, Product=32, SerialNumber=0
usb 1-1: default language 0x0409
usb 1-1: Product: WingMan Gamepad
usb 1-1: Manufacturer: Logitech Inc.
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
uhci_hcd 0000:00:07.2: port 2 portsc 018a
hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.2: port 2 portsc 0188
hub 1-0:1.0: port 2 enable change, status 00000300
uhci_hcd 0000:00:07.3: port 1 portsc 018a
hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
uhci_hcd 0000:00:07.3: port 2 portsc 008a
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
uhci_hcd 0000:00:07.3: port 1 portsc 0188
hub 2-0:1.0: port 1 enable change, status 00000300
uhci_hcd 0000:00:07.3: port 2 portsc 0088
hub 2-0:1.0: port 2 enable change, status 00000100
uhci_hcd 0000:00:07.3: suspend_hc
uhci_hcd 0000:00:07.2: port 2 portsc 0093
hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
usb 1-2: new full speed USB device using address 3
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1 EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
usb 1-2: device not accepting address 3, error -71
usb 1-2: new full speed USB device using address 4
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1 EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
[e6fe4240] link (26fe41e2) element (26fe3040)
0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
usb 1-2: device not accepting address 4, error -71 uhci_hcd 0000:00:07.2: port 2 portsc 008a hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s uhci_hcd 0000:00:07.2: port 2 portsc 0088
lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
Flags: bus master, medium devsel, latency 8
Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management version 2
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: da000000-dbffffff
Prefetchable memory behind bridge: d8000000-d9ffffff
Capabilities: [80] Power Management version 2
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. Bus Master IDE
Flags: bus master, medium devsel, latency 32
I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
Subsystem: Unknown device 0925:1234
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
Flags: medium devsel, IRQ 7
Capabilities: [68] Power Management version 200:09.0 SCSI storage controller: Adaptec AHA-2940U2/W
Subsystem: Adaptec: Unknown device a180
Flags: bus master, medium devsel, latency 32, IRQ 11
BIST result: 00
I/O ports at dc00 [disabled] [size=256]
Memory at dd200000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 100:0d.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05)
Subsystem: Compaq Computer Corporation NC3120
Flags: bus master, medium devsel, latency 32, IRQ 10
Memory at dd203000 (32-bit, prefetchable) [size=4K]
I/O ports at ec00 [size=32]
Memory at dd100000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at <unassigned> [disabled] [size=1M]
Capabilities: [dc] Power Management version 101:00.0 VGA compatible controller: nVidia Corporation Vanta [NV6] (rev 15) (prog-if 00 [VGA])
Subsystem: Unknown device 17f2:4010
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
Memory at da000000 (32-bit, non-prefetchable) [size=16M]
Memory at d8000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 2.0
cat /proc/bus/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.7 uhci_hcd S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) S: SerialNumber=0000:00:07.3 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.7 uhci_hcd S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller S: SerialNumber=0000:00:07.2 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=046d ProdID=c209 Rev= 1.03 S: Manufacturer=Logitech Inc. S: Product=WingMan Gamepad C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 40mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none) E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
cat /proc/interrupts
CPU0
0: 2040665 XT-PIC timer
1: 8 XT-PIC i8042
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
10: 71185 XT-PIC EMU10K1, uhci_hcd, uhci_hcd, eth1
11: 19586 XT-PIC aic7xxx
12: 30728 XT-PIC Bt87x audio, bttv0, eth0
15: 18 XT-PIC ide1
NMI: 0
LOC: 2040654
ERR: 2234
MIS: 0-------------------------------------------------------
This SF.Net email sponsored by Black Hat Briefings & Training.
Attend Black Hat Briefings & Training, Las Vegas July 24-29 - digital self defense, top technical experts, no vendor pitches, unmatched networking opportunities. Visit www.blackhat.com
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
