> It would help a lot if you would set CONFIG_USB_STORAGE_DEBUG and capture
> the boot-up system log. Without some additional information there's no
> way to tell what's happening with your system.
>
> You might find that upgrading to 2.6.11-current solves the problems.
I am already running 2.6.11-rc3 and the problem has not gone away. Are
there any relevant fixes in -bk?
Attached is the bootup log after enabling CONFIG_USB_STORAGE_DEBUG.
Parag
es, LIFO batch:1
Normal zone: 192368 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
Nvidia board detected. Ignoring ACPI timer override.
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ e8000000 size 128 MB
Built 1 zonelists
Kernel command line: ro root=LABEL=/ vga=788 3 console=tty0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 131072 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1595.907 MHz processor.
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Memory: 767640k/785856k available (2560k kernel code, 17632k reserved, 1104k
data, 172k init)
Calibrating delay loop... 3162.11 BogoMIPS (lpj=1581056)
Security Framework v1.0.0 initialized
Capability LSM initialized
Failure registering Root Plug module with the kernel
Failure registering Root Plug module with primary security module.
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU: AMD Athlon(tm) 64 Processor 3200+ stepping 08
Using local APIC NMI watchdog using perfctr0
Using local APIC timer interrupts.
Detected 12.468 MHz APIC timer.
checking if image is initramfs... it is
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050125
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 33)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK2] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LNK3] (IRQs 17) *0
ACPI: PCI Interrupt Link [LNK4] (IRQs 16 18 19) *0, disabled.
ACPI: PCI Interrupt Link [LNK5] (IRQs 16 18 19) *0
ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LMCI] (IRQs 20 21 22) *0
ACPI: PCI Interrupt Link [LPID] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 20 21 22) *0, disabled.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically. If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device(). As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior. If this argument makes the device work again,
** please email the output of "lspci" to [EMAIL PROTECTED]
** so I can fix the driver.
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: Maximum main memory to use for agp memory: 690M
agpgart: AGP aperture is 128M @ 0xe8000000
PCI-DMA: Disabling IOMMU.
Simple Boot Flag at 0x37 set to 0x1
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
vesafb: framebuffer at 0xf0000000, mapped to 0xffffc20000100000, using 1875k,
total 65536k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (61 C)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
ACPI: PS/2 Mouse Controller [PS2M] at irq 12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ACPI: PCI Interrupt Link [LMCI] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 22 (level, low) -> IRQ 177
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
Losing some ticks... checking if CPU frequency changed.
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHT2060AT PL, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVD+RW GCA-4040N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 128KiB
hda: 117210240 sectors (60011 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 hda3 hda4 < hda5 >
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 56Kbytes
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.00.09e)
powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x2 (1500 mV)
powernow-k8: 1 : fid 0x8 (1600 MHz), vid 0xa (1300 mV)
powernow-k8: 2 : fid 0x0 (800 MHz), vid 0x12 (1100 mV)
cpu_init done, current fid 0x8, vid 0xa
ACPI wakeup devices:
USB0 USB1 USB2 PS2K PS2M MAC0
ACPI: (supports S0 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
Freeing unused kernel memory: 172k freed
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 19
ACPI: PCI interrupt 0000:02:01.0[A] -> GSI 19 (level, low) -> IRQ 185
eth0: RealTek RTL8139 at 0xffffc20000020800, 00:0f:b0:01:01:65, IRQ 185
eth0: Identified 8139 chip type 'RTL-8101'
ndiswrapper version 1.0 loaded (preempt=yes,smp=no)
ndiswrapper: driver netbc564 (,10/01/2002,3.70.17.5) added
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 17
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 17 (level, low) -> IRQ 193
ndiswrapper: using irq 193
wlan0: ndiswrapper ethernet device 00:90:4b:59:55:37 using driver netbc564
wlan0: encryption modes supported: WEP, WPA with TKIP, WPA with AES/CCMP
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 21 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 49464 usecs
intel8x0: clocking to 47485
ACPI: PCI interrupt 0000:00:06.1[B] -> GSI 22 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:06.1 to 64
i2c_adapter i2c-0: nForce2 SMBus adapter at 0x2040
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2000
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 20
ACPI: PCI interrupt 0000:00:02.2[C] -> GSI 20 (level, low) -> IRQ 209
ehci_hcd 0000:00:02.2: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 209, pci mem 0xe0004000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: park 0
ehci_hcd 0000:00:02.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Enabling device 0000:00:02.0 (0004 -> 0006)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 22
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 22 (level, low) -> IRQ 177
ohci_hcd 0000:00:02.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 177, pci mem 0xe0000000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Enabling device 0000:00:02.1 (0004 -> 0006)
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 21
ACPI: PCI interrupt 0000:00:02.1[B] -> GSI 21 (level, low) -> IRQ 201
ohci_hcd 0000:00:02.1: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: irq 201, pci mem 0xe0001000
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
usb 1-1: new high speed USB device using ehci_hcd and address 2
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
ohci1394: $Rev: 1223 $ Ben Collins <[EMAIL PROTECTED]>
ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 18
ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 217
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[217] MMIO=[e0108000-e01087ff]
Max Packet=[2048]
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage: USB Mass Storage device detected
usb-storage: -- associate_dev
usb-storage: Vendor: 0x0d49, Product: 0x7000, Revision: 0x0200
usb-storage: Interface Subclass: 0x06, Protocol: 0x50
usb-storage: Vendor: Maxtor, Product: OneTouch
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is -32, data is 0
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=88 len=0
usb-storage: usb_stor_clear_halt: result = 0
usb-storage: usb_stor_control_msg: rq=01 rqtype=02 value=0000 index=02 len=0
usb-storage: usb_stor_clear_halt: result = 0
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: *** thread sleeping.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
ieee1394: Host added: ID:BUS[0-00:1023] GUID[463f0200463f0200]
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ibm_acpi: ec object not found
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
EXT3 FS on hda5, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1052248k swap on /dev/hda3. Priority:-1 extents:1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Maxtor Model: OneTouch Rev: 0201
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x9 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xa L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 398295040 512-byte hdwr sectors (203927 MB)
sda: assuming drive cache: write through
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0xc L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 398295040 512-byte hdwr sectors (203927 MB)
sda: assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xd L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
input: PS/2 Generic Mouse on isa0060/serio4
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 17 bd 52 4c 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xe L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 0c 34 f2 cc 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0xf L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 0c 34 f2 d4 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x10 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x10 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 0c 34 f2 dc 00 00 78 00
usb-storage: Bulk Command S 0x43425355 T 0x11 L 61440 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 61440 bytes, 11 entries
usb-storage: Status code 0; transferred 61440/61440
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 40 00
usb-storage: Bulk Command S 0x43425355 T 0x12 L 32768 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 32768 bytes, 8 entries
usb-storage: Status code 0; transferred 32768/32768
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x12 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 0c 34 f2 3f 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x13 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x13 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 3f 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x14 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x14 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 47 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x15 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x15 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 4f 00 00 78 00
usb-storage: Bulk Command S 0x43425355 T 0x16 L 61440 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 61440 bytes, 15 entries
usb-storage: Status code 0; transferred 61440/61440
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x16 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 02 3f 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x17 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x17 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 60 00 3f 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x18 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x18 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 40 00
usb-storage: Bulk Command S 0x43425355 T 0x19 L 32768 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 32768 bytes, 4 entries
usb-storage: Status code 0; transferred 32768/32768
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x19 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
