Hi,
I am trying to get the isp1362-hcd driver running on a custom PXA board . Got
lots of info from the list archives, had to pull the H_WAKE pin low to get
the clock trigger ready (Thanks to the list archives :) )
IRQ 27 is assinged to ISP1362 INT1, but i am getting the error irq 25 :nobody
cared ...... then i enabled the CHIP_BUFFER_TEST to realise it fails .
Could some one tell me why the buffer test would fail ?
Regards,
Vishal
driver isp1362-hcd, 2005-04-04
IRQ27 (GPIO4): <7>falling <7>edges
isp1362-hcd isp1362-hcd0: ISP1362 Host Controller
isp1362_hc_reset:
isp1362_sw_reset:
Software reset done .....
Chip ID Read test ok ... 3630
isp1362-hcd isp1362-hcd0: new USB bus registered, assigned bus number 1
isp1362-hcd isp1362-hcd0: irq 27, io mem 0x08000000
isp1362_hc_start:
isp1362-hcd isp1362-hcd0: ISP1362 Memory usage:
isp1362-hcd isp1362-hcd0: ISTL: 2 * 256: 512 @ $0000:$0100
irq25: nobody cared
pc : [<c00b6834>] lr : [<c00b684c>] Not tainted
sp : c10e1d98 ip : f2100000 fp : c10e1dc0
r10: 00000046 r9 : 00000055 r8 : 00000006
r7 : c017eb42 r6 : 00000020 r5 : 000026fe r4 : c0172f44
r3 : f2100000 r2 : 000000f2 r1 : 0000000d r0 : 00000001
Flags: Nzcv IRQs on FIQs on Mode SVC_32 Segment user
Control: 397F Table: A10A8000 DAC: 00000015
Function entered at [<c001bbb0>] from [<c001be1c>]
r5 = 00000019 r4 = C017ADA8
Function entered at [<c001bd54>] from [<c0023918>]
r7 = C10E1D50 r6 = 0000001A r5 = C017ADA8 r4 = 00000001
Function entered at [<c00238c8>] from [<c001c084>]
r7 = C00B6834 r6 = 00000400 r5 = C10E1D50 r4 = C10E0000
Function entered at [<c001c03c>] from [<c001ae80>]
r5 = F2D00000 r4 = C10E1D84
Function entered at [<c00b67e0>] from [<c002ae00>]
Function entered at [<c002ad98>] from [<c002afac>]
r6 = C016DCEC r5 = 00000CBE r4 = 00000CBE
Function entered at [<c002aea4>] from [<c002b344>]
r6 = C016DCF0 r5 = 60000013 r4 = FFFFF342
Function entered at [<c002b2f4>] from [<c002b234>]
r4 = C017DAF5
Function entered at [<c002b100>] from [<bf008cb0>]
r3 = 00000100 r2 = C016D8C8 r1 = BF00A02C r0 = BF00C1F4
r7 = C03B3000 r6 = 00000200 r5 = C03B3158 r4 = C03B3000
Function entered at [<bf008c44>] from [<bf009818>]
Function entered at [<bf0095b4>] from [<c00e4294>]
Function entered at [<c00e4024>] from [<bf00f234>]
r8 = 00000000 r7 = C03B3158 r6 = C016D814 r5 = C03B3000
r4 = C03B31AC
Function entered at [<bf00f000>] from [<c00b7dc0>]
Function entered at [<c00b7d78>] from [<c00b7ed4>]
r6 = C01733A8 r5 = BF00D2D4 r4 = C016D878
Function entered at [<c00b7e80>] from [<c00b8118>]
r6 = C017334C r5 = BF00D2D4 r4 = C0173300
Function entered at [<c00b80a0>] from [<c00b8450>]
r7 = 00000000 r6 = C016F1F4 r5 = BF00D340 r4 = C016F20C
Function entered at [<c00b8414>] from [<c003fffc>]
Function entered at [<c003fe60>] from [<c001b1a0>]
r7 = 00000080 r6 = 00000101 r5 = 00000000 r4 = 00000003
handlers:
[<c00c7f6c>]
isp1362-hcd isp1362-hcd0: INTL: 16 * ( 64+8): 1152 @ $0200
isp1362-hcd isp1362-hcd0: ATL : 32 * ( 64+8): 2304 @ $0680
isp1362-hcd isp1362-hcd0: USED/FREE: 3968 128
usb usb1: bogus endpoint ep0in in usb_submit_urb (bad maxpacket 0)
isp1362-hcd isp1362-hcd0: can't read usb1 device descriptor -90
isp1362_hc_stop:
isp1362_sw_reset:
Software reset done .....
Chip ID Read test ok ... 3630
isp1362-hcd isp1362-hcd0: startup error -19
isp1362-hcd isp1362-hcd0: USB bus 1 deregistered
init error, -19
------------------------------------------------------------------------------------------------------------------------------
driver isp1362-hcd, 2005-04-04
isp1362-hcd isp1362-hcd0: ISP1362 Host Controller
isp1362_hc_reset:
isp1362_sw_reset:
Software reset done .....
Chip ID Read test ok ... 3630
isp1362-hcd isp1362-hcd0: new USB bus registered, assigned bus number 1
isp1362-hcd isp1362-hcd0: irq 27, io mem 0x08000000
isp1362_hc_start:
isp1362_chip_test: memory check with 2 byte offset 0 failed
isp1362_chip_test: memory check with 3 byte offset 0 failed
isp1362_chip_test: memory check with 4 byte offset 0 failed
isp1362_chip_test: memory check with 5 byte offset 0 failed
isp1362_chip_test: memory check with 6 byte offset 0 failed
isp1362_chip_test: memory check with 7 byte offset 0 failed
isp1362_chip_test: memory check failed
isp1362_chip_test: memory check with offset 00 failed
chip_test() ret=-19
isp1362-hcd isp1362-hcd0: startup error -19
isp1362-hcd isp1362-hcd0: USB bus 1 deregistered
init error, -19
-------------------------------------------------------
This SF.Net email is sponsored by xPML, a groundbreaking scripting language
that extends applications into web and mobile media. Attend the live webcast
and join the prime developer group breaking into this new coding territory!
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=110944&bid=241720&dat=121642
_______________________________________________
[email protected]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
