On 6/28/07, Alan Stern <[EMAIL PROTECTED]> wrote:
On Thu, 28 Jun 2007, Branden Sletteland wrote:> I am seeing an issue when going from kernel version 2.6.20.14 to > 2.6.21 through 2.6.21.5 were my high speed devices are only being > recognized as full speed devices, with error output on a 2.6.21 kernel > stating: > > usb 3-1: new full speed USB device using ohci_hcd and address 11 > usb 3-1: not running at top speed; connect to a high speed hub > usb 3-1: configuration #1 chosen from 1 choice > > I'm using a Philips (NXP) ISP1563 PCI based host controller > (OHCI/EHCI) and my high speed mass storage devices are Cypress EZ-USB > FX2LP CY7C68013A devices with compact flash interfaces. > > This hardware setup is rock solid when running with a 2.6.20.14 > kernel, I have never seen the devices initialize as full speed USB > devices with this and earlier versions of 2.6.20. Please try building a kernel with CONFIG_USB_DEBUG enabled, and post the resulting dmesg log showing what happens during bootup and when one of your devices is plugged in. Alan Stern
Forgot to mention this is a ppc based processor. Attached is the dmesg output. Branden
entries: 1024 (order: 10, 4096 bytes) <6>time_init: decrementer frequency = 32.500000 MHz <4>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) <4>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) <4>Memory: 251648k available (1992k kernel code, 496k data, 5224k init, 0k highmem) <7>Calibrating delay loop... 972.80 BogoMIPS (lpj=1945600) <4>Mount-cache hash table entries: 512 <6>NET: Registered protocol family 16 <6>PCI: Probing PCI hardware <4>DTU-7100 I/O Board PCI device checking: <4> Bridge #1: FOUND. <4> Bridge #2: FOUND. <4> Bridge #1, OHCI #1: FOUND. <4> Bridge #1, OHCI #2: FOUND. <4> Bridge #1, EHCI #1: FOUND. <4> Bridge #1, Micrel #1: FOUND. <4> Bridge #2, Micrel #2: FOUND. <4> Bridge #2, OHCI #3: FOUND. <4> Bridge #2, OHCI #4: FOUND. <4> Bridge #2, EHCI #2: FOUND. <4> Bridge #2, Micrel #3: FOUND. <5>SCSI subsystem initialized <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>NET: Registered protocol family 2 <4>IP route cache hash table entries: 2048 (order: 1, 8192 bytes) <4>TCP established hash table entries: 8192 (order: 4, 65536 bytes) <4>TCP bind hash table entries: 8192 (order: 3, 32768 bytes) <6>TCP: Hash tables configured (established 8192 bind 8192) <6>TCP reno registered <6>Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). <6>JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. <6>io scheduler noop registered <6>io scheduler anticipatory registered (default) <6>io scheduler deadline registered <6>io scheduler cfq registered <6>Generic RTC Driver v1.07 <6>SPHAM Watchdog Driver <6>SPHAM watchdog timer started <6>Rockwell SPHAM UART Driver <6>SPHAM UART-A initialized <6>SPHAM UART-B initialized <6>loop: loaded (max 8 devices) <6>Rockwell SPHAM I2C Driver <4>I2C Bus 1 <4>I2C Bus 2 <4>RCI I2C Discrete driver <5>MV-643xx 10/100/1000 Ethernet Driver <5>eth0: port 0 with MAC address 02:00:00:01:01:15 <5>eth0: Scatter Gather Enabled <5>eth0: TX TCP/IP Checksumming Supported <5>eth0: RX TCP/UDP Checksum Offload ON <5>eth0: RX NAPI Enabled <5>eth1: port 1 with MAC address 02:00:00:02:01:15 <5>eth1: Scatter Gather Enabled <5>eth1: TX TCP/IP Checksumming Supported <5>eth1: RX TCP/UDP Checksum Offload ON <5>eth1: RX NAPI Enabled <4>Generic platform RAM MTD, (c) 2004 Simtec Electronics <5>SPHAM NOR device: 10000000 at f0000000 <6>3UCPR NOR Flash: Found 4 x16 devices at 0x0 in 32-bit bank <4> Amd/Fujitsu Extended Query Table at 0x0040 <4>3UCPR NOR Flash: CFI does not contain boot bank location. Assuming top. <5>number of CFI chips: 1 <5>cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. <5>Creating 5 MTD partitions on "3UCPR NOR Flash": <5>0x00000000-0x00100000 : "golden-kernel" <5>0x00100000-0x00e00000 : "kernel" <5>0x00e00000-0x02e00000 : "rokfs" <5>0x02e00000-0x04500000 : "appfs" <5>0x0ff00000-0x0ff80000 : "VMOS-boot" <5>Creating 3 MTD partitions on "3UCPR NOR Flash": <5>0x0ff80000-0x0ffc0000 : "SCT" <5>0x0ffc0000-0x0ffe0000 : "HW/SW-compat" <5>0x0ffe0000-0x10000000 : "Maint-data" <5>SPHAM NOVRAM device: 20000 at 40400000 <5>Creating 11 MTD partitions on "Rockwell SPHAM NOVRAM": <5>0x00000000-0x00000050 : "Reserved1" <5>0x00000050-0x00000054 : "Start Type" <5>0x00000054-0x00000058 : "Boot log" <5>0x00000058-0x00000070 : "Reserved2" <5>0x00000070-0x00000080 : "Lifecycle data" <5>0x00000080-0x00000180 : "Module fatal fault" <5>0x00000180-0x00000328 : "Reserved3" <5>0x00000328-0x00002328 : "Current maintenance log" <5>0x00002328-0x00009728 : "Historical maintenance log" <5>0x00009728-0x0000ff00 : "DTU NVM" <5>0x0000ff00-0x00010000 : "Hardware ID" <7>ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 <6>ehci_hcd 0000:01:0e.2: EHCI Host Controller <7>drivers/usb/core/inode.c: creating file 'devices' <7>drivers/usb/core/inode.c: creating file '001' <6>ehci_hcd 0000:01:0e.2: new USB bus registered, assigned bus number 1 <7>ehci_hcd 0000:01:0e.2: reset hcs_params 0x2294 dbg=0 cc=2 pcc=2 ports=4 <7>ehci_hcd 0000:01:0e.2: reset portroute 1 0 1 0 <7>ehci_hcd 0000:01:0e.2: reset hcc_params 0012 thresh 1 uframes 256/512/1024 <7>ehci_hcd 0000:01:0e.2: MWI active <7>ehci_hcd 0000:01:0e.2: ...powerdown ports... <7>ehci_hcd 0000:01:0e.2: supports USB remote wakeup <6>ehci_hcd 0000:01:0e.2: irq 74, io mem 0x9fffdf00 <7>ehci_hcd 0000:01:0e.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT <7>ehci_hcd 0000:01:0e.2: init command 010009 (park)=0 ithresh=1 period=256 RUN <6>ehci_hcd 0000:01:0e.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 <7>usb usb1: default language 0x0409 <7>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb1: Product: EHCI Host Controller <6>usb usb1: Manufacturer: Linux 2.6.21.5 ehci_hcd <6>usb usb1: SerialNumber: 0000:01:0e.2 <7>usb usb1: uevent <7>usb usb1: usb_probe_device <6>usb usb1: configuration #1 chosen from 1 choice <7>usb usb1: adding 1-0:1.0 (config #1, interface 0) <7>usb 1-0:1.0: uevent <7>hub 1-0:1.0: usb_probe_interface <7>hub 1-0:1.0: usb_probe_interface - got id <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 4 ports detected <7>hub 1-0:1.0: standalone hub <7>hub 1-0:1.0: individual port power switching <7>hub 1-0:1.0: individual port over-current protection <7>hub 1-0:1.0: Single TT <7>hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns) <7>hub 1-0:1.0: power on to power good time: 20ms <7>hub 1-0:1.0: local power source is good <7>hub 1-0:1.0: enabling power on all ports <7>hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <6>ehci_hcd 0000:02:0e.2: EHCI Host Controller <7>drivers/usb/core/inode.c: creating file '002' <6>ehci_hcd 0000:02:0e.2: new USB bus registered, assigned bus number 2 <7>ehci_hcd 0000:02:0e.2: reset hcs_params 0x2294 dbg=0 cc=2 pcc=2 ports=4 <7>ehci_hcd 0000:02:0e.2: reset portroute 1 0 1 0 <7>ehci_hcd 0000:02:0e.2: reset hcc_params 0012 thresh 1 uframes 256/512/1024 <7>ehci_hcd 0000:02:0e.2: MWI active <7>ehci_hcd 0000:02:0e.2: ...powerdown ports... <7>ehci_hcd 0000:02:0e.2: supports USB remote wakeup <6>ehci_hcd 0000:02:0e.2: irq 75, io mem 0x9fdfcf00 <7>ehci_hcd 0000:02:0e.2: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT <7>ehci_hcd 0000:02:0e.2: init command 010009 (park)=0 ithresh=1 period=256 RUN <6>ehci_hcd 0000:02:0e.2: USB 2.0 started, EHCI 0.95, driver 10 Dec 2004 <7>usb usb2: default language 0x0409 <7>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb2: Product: EHCI Host Controller <6>usb usb2: Manufacturer: Linux 2.6.21.5 ehci_hcd <6>usb usb2: SerialNumber: 0000:02:0e.2 <7>usb usb2: uevent <7>usb usb2: usb_probe_device <6>usb usb2: configuration #1 chosen from 1 choice <7>usb usb2: adding 2-0:1.0 (config #1, interface 0) <7>usb 2-0:1.0: uevent <7>hub 2-0:1.0: usb_probe_interface <7>hub 2-0:1.0: usb_probe_interface - got id <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 4 ports detected <7>hub 2-0:1.0: standalone hub <7>hub 2-0:1.0: individual port power switching <7>hub 2-0:1.0: individual port over-current protection <7>hub 2-0:1.0: Single TT <7>hub 2-0:1.0: TT requires at most 8 FS bit times (666 ns) <7>hub 2-0:1.0: power on to power good time: 20ms <7>hub 2-0:1.0: local power source is good <7>hub 2-0:1.0: enabling power on all ports <7>hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <7>ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver <7>ohci_hcd: block sizes: ed 64 td 64 <6>ohci_hcd 0000:01:0e.0: OHCI Host Controller <7>drivers/usb/core/inode.c: creating file '003' <6>ohci_hcd 0000:01:0e.0: new USB bus registered, assigned bus number 3 <7>ohci_hcd 0000:01:0e.0: created debug files <6>ohci_hcd 0000:01:0e.0: irq 74, io mem 0x9ffff000 <7>ohci_hcd 0000:01:0e.0: resetting from state 'reset', control = 0x0 <7>ohci_hcd 0000:01:0e.0: OHCI controller state <7>ohci_hcd 0000:01:0e.0: OHCI 1.0, NO legacy support registers <7>ohci_hcd 0000:01:0e.0: control 0x083 HCFS=operational CBSR=3 <7>ohci_hcd 0000:01:0e.0: cmdstatus 0x00000 SOC=0 <7>ohci_hcd 0000:01:0e.0: intrstatus 0x00000004 SF <7>ohci_hcd 0000:01:0e.0: intrenable 0x8000001a MIE UE RD WDH <7>ohci_hcd 0000:01:0e.0: hcca frame #01f2 <7>ohci_hcd 0000:01:0e.0: roothub.a ff000202 POTPGT=255 NPS NDP=2(2) <7>ohci_hcd 0000:01:0e.0: roothub.b 00000000 PPCM=0000 DR=0000 <7>ohci_hcd 0000:01:0e.0: roothub.status 00008000 DRWE <7>ohci_hcd 0000:01:0e.0: roothub.portstatus [0] 0x00000100 PPS <7>ohci_hcd 0000:01:0e.0: roothub.portstatus [1] 0x00000100 PPS <7>usb usb3: default language 0x0409 <7>usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb3: Product: OHCI Host Controller <6>usb usb3: Manufacturer: Linux 2.6.21.5 ohci_hcd <6>usb usb3: SerialNumber: 0000:01:0e.0 <7>usb usb3: uevent <7>usb usb3: usb_probe_device <6>usb usb3: configuration #1 chosen from 1 choice <7>usb usb3: adding 3-0:1.0 (config #1, interface 0) <7>usb 3-0:1.0: uevent <7>hub 3-0:1.0: usb_probe_interface <7>hub 3-0:1.0: usb_probe_interface - got id <6>hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 2 ports detected <7>hub 3-0:1.0: standalone hub <7>hub 3-0:1.0: no power switching (usb 1.0) <7>hub 3-0:1.0: global over-current protection <7>hub 3-0:1.0: power on to power good time: 510ms <7>hub 3-0:1.0: local power source is good <7>hub 3-0:1.0: no over-current condition exists <7>hub 3-0:1.0: trying to enable port power on non-switchable hub <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <6>ohci_hcd 0000:01:0e.1: OHCI Host Controller <7>drivers/usb/core/inode.c: creating file '004' <6>ohci_hcd 0000:01:0e.1: new USB bus registered, assigned bus number 4 <7>ohci_hcd 0000:01:0e.1: created debug files <6>ohci_hcd 0000:01:0e.1: irq 74, io mem 0x9fffe000 <7>ohci_hcd 0000:01:0e.1: resetting from state 'reset', control = 0x0 <7>ohci_hcd 0000:01:0e.1: OHCI controller state <7>ohci_hcd 0000:01:0e.1: OHCI 1.0, NO legacy support registers <7>ohci_hcd 0000:01:0e.1: control 0x083 HCFS=operational CBSR=3 <7>ohci_hcd 0000:01:0e.1: cmdstatus 0x00000 SOC=0 <7>ohci_hcd 0000:01:0e.1: intrstatus 0x00000004 SF <7>ohci_hcd 0000:01:0e.1: intrenable 0x8000001a MIE UE RD WDH <7>ohci_hcd 0000:01:0e.1: hcca frame #01f2 <7>ohci_hcd 0000:01:0e.1: roothub.a ff000202 POTPGT=255 NPS NDP=2(2) <7>ohci_hcd 0000:01:0e.1: roothub.b 00000000 PPCM=0000 DR=0000 <7>ohci_hcd 0000:01:0e.1: roothub.status 00008000 DRWE <7>ohci_hcd 0000:01:0e.1: roothub.portstatus [0] 0x00000100 PPS <7>ohci_hcd 0000:01:0e.1: roothub.portstatus [1] 0x00000100 PPS <7>usb usb4: default language 0x0409 <7>usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb4: Product: OHCI Host Controller <6>usb usb4: Manufacturer: Linux 2.6.21.5 ohci_hcd <6>usb usb4: SerialNumber: 0000:01:0e.1 <7>usb usb4: uevent <7>usb usb4: usb_probe_device <6>usb usb4: configuration #1 chosen from 1 choice <7>usb usb4: adding 4-0:1.0 (config #1, interface 0) <7>usb 4-0:1.0: uevent <7>hub 4-0:1.0: usb_probe_interface <7>hub 4-0:1.0: usb_probe_interface - got id <6>hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 2 ports detected <7>hub 4-0:1.0: standalone hub <7>hub 4-0:1.0: no power switching (usb 1.0) <7>hub 4-0:1.0: global over-current protection <7>hub 4-0:1.0: power on to power good time: 510ms <7>hub 4-0:1.0: local power source is good <7>hub 4-0:1.0: no over-current condition exists <7>hub 4-0:1.0: trying to enable port power on non-switchable hub <7>hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <6>ohci_hcd 0000:02:0e.0: OHCI Host Controller <7>drivers/usb/core/inode.c: creating file '005' <6>ohci_hcd 0000:02:0e.0: new USB bus registered, assigned bus number 5 <7>ohci_hcd 0000:02:0e.0: created debug files <6>ohci_hcd 0000:02:0e.0: irq 75, io mem 0x9fdfe000 <7>ohci_hcd 0000:02:0e.0: resetting from state 'reset', control = 0x0 <7>ohci_hcd 0000:02:0e.0: OHCI controller state <7>ohci_hcd 0000:02:0e.0: OHCI 1.0, NO legacy support registers <7>ohci_hcd 0000:02:0e.0: control 0x083 HCFS=operational CBSR=3 <7>ohci_hcd 0000:02:0e.0: cmdstatus 0x00000 SOC=0 <7>ohci_hcd 0000:02:0e.0: intrstatus 0x00000004 SF <7>ohci_hcd 0000:02:0e.0: intrenable 0x8000001a MIE UE RD WDH <7>ohci_hcd 0000:02:0e.0: hcca frame #01f2 <7>ohci_hcd 0000:02:0e.0: roothub.a ff000202 POTPGT=255 NPS NDP=2(2) <7>ohci_hcd 0000:02:0e.0: roothub.b 00000000 PPCM=0000 DR=0000 <7>ohci_hcd 0000:02:0e.0: roothub.status 00008000 DRWE <7>ohci_hcd 0000:02:0e.0: roothub.portstatus [0] 0x00000100 PPS <7>ohci_hcd 0000:02:0e.0: roothub.portstatus [1] 0x00000100 PPS <7>usb usb5: default language 0x0409 <7>usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb5: Product: OHCI Host Controller <6>usb usb5: Manufacturer: Linux 2.6.21.5 ohci_hcd <6>usb usb5: SerialNumber: 0000:02:0e.0 <7>usb usb5: uevent <7>usb usb5: usb_probe_device <6>usb usb5: configuration #1 chosen from 1 choice <7>usb usb5: adding 5-0:1.0 (config #1, interface 0) <7>usb 5-0:1.0: uevent <7>hub 5-0:1.0: usb_probe_interface <7>hub 5-0:1.0: usb_probe_interface - got id <6>hub 5-0:1.0: USB hub found <6>hub 5-0:1.0: 2 ports detected <7>hub 5-0:1.0: standalone hub <7>hub 5-0:1.0: no power switching (usb 1.0) <7>hub 5-0:1.0: global over-current protection <7>hub 5-0:1.0: power on to power good time: 510ms <7>hub 5-0:1.0: local power source is good <7>hub 5-0:1.0: no over-current condition exists <7>hub 5-0:1.0: trying to enable port power on non-switchable hub <7>hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <6>ohci_hcd 0000:02:0e.1: OHCI Host Controller <7>drivers/usb/core/inode.c: creating file '006' <6>ohci_hcd 0000:02:0e.1: new USB bus registered, assigned bus number 6 <7>ohci_hcd 0000:02:0e.1: created debug files <6>ohci_hcd 0000:02:0e.1: irq 75, io mem 0x9fdfd000 <7>ohci_hcd 0000:02:0e.1: resetting from state 'reset', control = 0x0 <7>ohci_hcd 0000:02:0e.1: OHCI controller state <7>ohci_hcd 0000:02:0e.1: OHCI 1.0, NO legacy support registers <7>ohci_hcd 0000:02:0e.1: control 0x083 HCFS=operational CBSR=3 <7>ohci_hcd 0000:02:0e.1: cmdstatus 0x00000 SOC=0 <7>ohci_hcd 0000:02:0e.1: intrstatus 0x00000004 SF <7>ohci_hcd 0000:02:0e.1: intrenable 0x8000001a MIE UE RD WDH <7>ohci_hcd 0000:02:0e.1: hcca frame #01f2 <7>ohci_hcd 0000:02:0e.1: roothub.a ff000202 POTPGT=255 NPS NDP=2(2) <7>ohci_hcd 0000:02:0e.1: roothub.b 00000000 PPCM=0000 DR=0000 <7>ohci_hcd 0000:02:0e.1: roothub.status 00008000 DRWE <7>ohci_hcd 0000:02:0e.1: roothub.portstatus [0] 0x00000100 PPS <7>ohci_hcd 0000:02:0e.1: roothub.portstatus [1] 0x00000100 PPS <7>usb usb6: default language 0x0409 <7>usb usb6: new device strings: Mfr=3, Product=2, SerialNumber=1 <6>usb usb6: Product: OHCI Host Controller <6>usb usb6: Manufacturer: Linux 2.6.21.5 ohci_hcd <6>usb usb6: SerialNumber: 0000:02:0e.1 <7>usb usb6: uevent <7>usb usb6: usb_probe_device <6>usb usb6: configuration #1 chosen from 1 choice <7>usb usb6: adding 6-0:1.0 (config #1, interface 0) <7>usb 6-0:1.0: uevent <7>hub 6-0:1.0: usb_probe_interface <7>hub 6-0:1.0: usb_probe_interface - got id <6>hub 6-0:1.0: USB hub found <6>hub 6-0:1.0: 2 ports detected <7>hub 6-0:1.0: standalone hub <7>hub 6-0:1.0: no power switching (usb 1.0) <7>hub 6-0:1.0: global over-current protection <7>hub 6-0:1.0: power on to power good time: 510ms <7>hub 6-0:1.0: local power source is good <7>hub 6-0:1.0: no over-current condition exists <7>hub 6-0:1.0: trying to enable port power on non-switchable hub <7>hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 <7>drivers/usb/core/inode.c: creating file '001' <6>Initializing USB Mass Storage driver... <6>usbcore: registered new interface driver usb-storage <6>USB Mass Storage support registered. <6>TCP cubic registered <6>NET: Registered protocol family 1 <6>NET: Registered protocol family 17 <4>Freeing unused kernel memory: 5224k init <7>PCI: 0000:01:0f.0 has unsupported PM cap regs version (7) <6>Micrel KSZ8841 PCI 1.0.9 (May 4, 2007) Mem = c1064000; IRQ = 75 <4>eth2: Mem = c1064000, IRQ = 75 <7>PCI: 0000:02:0d.0 has unsupported PM cap regs version (7) <6>Micrel KSZ8841 PCI 1.0.9 (May 4, 2007) Mem = c1066800; IRQ = 74 <4>eth3: Mem = c1066800, IRQ = 74 <7>PCI: 0000:02:0f.0 has unsupported PM cap regs version (7) <6>Micrel KSZ8841 PCI 1.0.9 (May 4, 2007) Mem = c1068000; IRQ = 76 <4>eth4: Mem = c1068000, IRQ = 76 <7>hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0002 <7>ehci_hcd 0000:01:0e.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT <7>hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s <7>hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 <7>ehci_hcd 0000:01:0e.2: port 1 full speed --> companion <7>ehci_hcd 0000:01:0e.2: GetStatus port 1 status 003001 POWER OWNER sig=se0 CONNECT <7>hub 1-0:1.0: port 1 not reset yet, waiting 50ms <7>ehci_hcd 0000:01:0e.2: GetStatus port 1 status 003002 POWER OWNER sig=se0 CSC <7>hub 1-0:1.0: state 7 ports 4 chg 0000 evt 0002 <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00010101 CSC PPS CCS <7>hub 3-0:1.0: port 1, status 0101, change 0001, 12 Mb/s <7>hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: new full speed USB device using ohci_hcd and address 2 <7>ohci_hcd 0000:01:0e.0: urb b06077a0 path 1 ep0in 5ec20000 cc 5 --> status -62 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: not running at top speed; connect to a high speed hub <7>usb 3-1: default language 0x0409 <7>usb 3-1: new device strings: Mfr=74, Product=57, SerialNumber=44 <6>usb 3-1: Product: CPN 984-3815-001 <6>usb 3-1: Manufacturer: Rockwell Collins Inc. <6>usb 3-1: SerialNumber: 445455502333 <7>usb 3-1: uevent <7>usb 3-1: usb_probe_device <6>usb 3-1: configuration #1 chosen from 1 choice <7>usb 3-1: adding 3-1:1.0 (config #1, interface 0) <7>usb 3-1:1.0: uevent <7>usb-storage 3-1:1.0: usb_probe_interface <7>usb-storage 3-1:1.0: usb_probe_interface - got id <6>scsi0 : SCSI emulation for USB Mass Storage devices <7>drivers/usb/core/inode.c: creating file '002' <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 <7>usb-storage: device found at 2 <7>usb-storage: waiting for device to settle before scanning <7>ohci_hcd 0000:01:0e.0: urb b0607ce0 path 1 ep6in 5c120000 cc 5 --> status -62 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: reset full speed USB device using ohci_hcd and address 2 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 <7>ohci_hcd 0000:01:0e.0: urb b0607ce0 path 1 ep0out 5ec20000 cc 5 --> status -62 <3>usb 3-1: failed to restore interface 0 altsetting 0 (error=-62) <7>hub 3-0:1.0: logical disconnect on port 1 <7>hub 3-0:1.0: state 7 ports 2 chg 0002 evt 0002 <7>hub 3-0:1.0: port 1, status 0101, change 0000, 12 Mb/s <6>usb 3-1: USB disconnect, address 2 <7>usb 3-1: unregistering device <7>usb 3-1: usb_disable_device nuking all URBs <7>usb 3-1: unregistering interface 3-1:1.0 <7> usbdev3.2_ep02: ep_device_release called for usbdev3.2_ep02 <7> usbdev3.2_ep86: ep_device_release called for usbdev3.2_ep86 <7> usbdev3.2_ep81: ep_device_release called for usbdev3.2_ep81 <7>usb-storage: device scan complete <7>usb 3-1:1.0: uevent <7> usbdev3.2_ep00: ep_device_release called for usbdev3.2_ep00 <7>usb 3-1: uevent <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: new full speed USB device using ohci_hcd and address 3 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: not running at top speed; connect to a high speed hub <7>usb 3-1: default language 0x0409 <7>usb 3-1: new device strings: Mfr=74, Product=57, SerialNumber=44 <6>usb 3-1: Product: CPN 984-3815-001 <6>usb 3-1: Manufacturer: Rockwell Collins Inc. <6>usb 3-1: SerialNumber: 445455502333 <7>usb 3-1: uevent <7>usb 3-1: usb_probe_device <6>usb 3-1: configuration #1 chosen from 1 choice <7>usb 3-1: adding 3-1:1.0 (config #1, interface 0) <7>usb 3-1:1.0: uevent <7>usb-storage 3-1:1.0: usb_probe_interface <7>usb-storage 3-1:1.0: usb_probe_interface - got id <6>scsi1 : SCSI emulation for USB Mass Storage devices <7>drivers/usb/core/inode.c: creating file '003' <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 <7>usb-storage: device found at 3 <7>usb-storage: waiting for device to settle before scanning <7>ohci_hcd 0000:01:0e.0: urb b0607920 path 1 ep0in 5ec20000 cc 5 --> status -62 <5>scsi 1:0:0:0: Direct-Access Cypress Semi PQ: 0 ANSI: 0 <7>ohci_hcd 0000:01:0e.0: urb b0607920 path 1 ep6in 5d160000 cc 5 --> status -62 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <6>usb 3-1: reset full speed USB device using ohci_hcd and address 3 <7>ohci_hcd 0000:01:0e.0: GetStatus roothub.portstatus [0] = 0x00100103 PRSC PPS PES CCS <7>hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0002 <7> usbdev3.3_ep02: ep_device_release called for usbdev3.3_ep02 <7> usbdev3.3_ep86: ep_device_release called for usbdev3.3_ep86 <7> usbdev3.3_ep81: ep_device_release called for usbdev3.3_ep81 <5>SCSI device sda: 4001760 512-byte hdwr sectors (2049 MB) <7>ohci_hcd 0000:01:0e.0: urb b0607740 path 1 ep6in 90120000 cc 9 --> status -121 <7>ohci_hcd 0000:01:0e.0: urb b0607920 path 1 ep6in 40160000 cc 4 --> status -32 <5>sda: Write Protect is off <7>sda: Mode Sense: 27 00 00 00 <3>sda: assuming drive cache: write through <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <5>SCSI device sda: 4001760 512-byte hdwr sectors (2049 MB) <7>ohci_hcd 0000:01:0e.0: urb b0607740 path 1 ep6in 90120000 cc 9 --> status -121 <7>ohci_hcd 0000:01:0e.0: urb b0607920 path 1 ep6in 40160000 cc 4 --> status -32 <5>sda: Write Protect is off <7>sda: Mode Sense: 27 00 00 00 <3>sda: assuming drive cache: write through <6> sda: sda1 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <5>sd 1:0:0:0: Attached scsi removable disk sda <7>usb-storage: device scan complete <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0 <6>sd 1:0:0:0: ioctl_internal_command return code = 8000002 <6> : Current: sense key=0x0 <6> ASC=0x0 ASCQ=0x0
------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/
_______________________________________________ linux-usb-devel@lists.sourceforge.net To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-devel
