Problem: usb-ohci seems broken on AMD-765 Viper usb-ohci
Summary: Although the usb-ohci driver loads successfully, attempting to use
my usb device under any system load causes the generation of spurious calls
to usb_hub_port_connect_change from usb_hub_events.
Detailed: I am using an ov511 webcam, which worked perfectly on my old
system, and still works fine with an usb-uhci pci card I temporarily
installed for testing. However, the onboard usb-ohci [USB Controller:
Advanced Micro Devices [AMD] AMD-765 [Viper] USB (rev 7)] that is on my
Tyan Tiger-MP motherboard [which is a SMP board, but currently only has 1
cpu on it, a 1600Mhz K7, kernel compiled for uniprocessor] will work for
only brief intervals, before a spurious false disconnection causes the
device to be remapped to a different minor number. If the system load is
minimal, it will work fine for sometimes upwards of a minute
[i.e. displaying video in xawtv], but if there is any notable CPU
utilization, the problem will immediately arise within a few seconds at
most.
System log below demonstrates the problem. I would greatly appreciate any
suggestions you might have as to the cause of this. Is it possible that I
recieved a faulty motherboard, or is this a bug in the driver?
Thank you for your time and consideration.
David
-----
extract from syslog
--
Feb 22 00:21:12 ever kernel: usb-ohci.c: USB OHCI at membase 0xc00dc000, IRQ 11
Feb 22 00:21:12 ever kernel: usb-ohci.c: usb-00:07.4, Advanced Micro Devices [AMD]
AMD-765 [Viper] USB
Feb 22 00:21:12 ever kernel: usb.c: new USB bus registered, assigned bus number 1
Feb 22 00:21:12 ever kernel: Product: USB OHCI Root Hub
Feb 22 00:21:12 ever kernel: SerialNumber: c00dc000
Feb 22 00:21:12 ever kernel: hub.c: USB hub found
Feb 22 00:21:12 ever kernel: hub.c: 4 ports detected
Feb 22 00:21:12 ever kernel: usb.c: registered new driver ov511
Feb 22 00:21:12 ever kernel: ov511.c: v1.48 : OV511 USB Camera Driver
Feb 22 00:21:12 ever kernel: hub.c: USB new device connect on bus1/2, assigned device
number 2
Feb 22 00:21:13 ever kernel: ov511.c: [ov51x_probe:7171] probing for device...
Feb 22 00:21:13 ever kernel: ov511.c: USB OV511+ camera found
Feb 22 00:21:13 ever kernel: ov511.c: [ov511_configure:6906] CustomID = 0
Feb 22 00:21:13 ever kernel: ov511.c: model: Generic Camera (no ID)
Feb 22 00:21:13 ever kernel: ov511.c: [ov51x_init_ov_sensor:1904] I2C synced in 1
attempt(s)
Feb 22 00:21:13 ever kernel: ov511.c: [ov6xx0_configure:6586] OV6xx0 sensor detected
Feb 22 00:21:13 ever kernel: ov511.c: Sensor is an OV6620
Feb 22 00:21:13 ever kernel: ov511.c: Device registered on minor 1
Feb 22 00:21:29 ever kernel: usb.c: USB disconnect on device 2
Feb 22 00:21:29 ever kernel: hub.c: USB new device connect on bus1/2, assigned device
number 3
Feb 22 00:21:29 ever kernel: ov511.c: [ov51x_probe:7171] probing for device...
Feb 22 00:21:29 ever kernel: ov511.c: USB OV511+ camera found
Feb 22 00:21:29 ever kernel: ov511.c: [ov511_configure:6906] CustomID = 0
Feb 22 00:21:29 ever kernel: ov511.c: model: Generic Camera (no ID)
Feb 22 00:21:29 ever kernel: ov511.c: [ov51x_init_ov_sensor:1904] I2C synced in 1
attempt(s)
Feb 22 00:21:29 ever kernel: ov511.c: [ov6xx0_configure:6586] OV6xx0 sensor detected
Feb 22 00:21:29 ever kernel: ov511.c: Sensor is an OV6620
Feb 22 00:21:30 ever kernel: ov511.c: Device registered on minor 2
Feb 22 00:21:30 ever modprobe: modprobe: Can't locate module char-major-81-1
Feb 22 00:21:30 ever kernel: usb.c: USB disconnect on device 3
Feb 22 00:21:30 ever kernel: hub.c: USB new device connect on bus1/2, assigned device
number 4
Feb 22 00:21:30 ever kernel: ov511.c: [ov51x_probe:7171] probing for device...
Feb 22 00:21:30 ever kernel: ov511.c: USB OV511+ camera found
Feb 22 00:21:30 ever kernel: ov511.c: [ov511_configure:6906] CustomID = 0
Feb 22 00:21:30 ever kernel: ov511.c: model: Generic Camera (no ID)
Feb 22 00:21:30 ever kernel: ov511.c: [ov51x_init_ov_sensor:1904] I2C synced in 1
attempt(s)
Feb 22 00:21:30 ever kernel: ov511.c: [ov6xx0_configure:6586] OV6xx0 sensor detected
Feb 22 00:21:30 ever kernel: ov511.c: Sensor is an OV6620
Feb 22 00:21:31 ever kernel: ov511.c: Device registered on minor 1
--------
output of ver-linux:
--
Linux ever.mine.nu 2.4.17 #5 Tue Feb 12 10:43:36 EST 2002 i686 unknown
Gnu C 2.96
Gnu make 3.79.1
binutils 2.11.90.0.8
util-linux 2.11f
mount 2.11g
modutils 2.4.6
e2fsprogs 1.23
reiserfsprogs 3.x.0j
pcmcia-cs 3.1.22
PPP 2.4.1
Linux C Library 2.2.4
Dynamic linker (ldd) 2.2.4
Procps 2.0.7
Net-tools 1.60
Console-tools 0.3.3
Sh-utils 2.0.11
Modules Loaded ov511 usb-ohci videodev es1371 ac97_codec aic7xxx via-rhine
-----
output of /proc/cpuinfo
--
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 6
model name : AMD Athlon(tm) MP Processor 1900+
stepping : 2
cpu MHz : 1600.089
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat
pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 3191.60
-----
output of /proc/modules
--
ov511_dwb 72816 0
usb-ohci 19360 0 (unused)
videodev 4768 5 [ov511_dwb bttv]
es1371 26016 0 (autoclean)
ac97_codec 9376 0 (autoclean) [es1371]
aic7xxx 109776 0 (unused)
NVdriver 820256 14 (autoclean)
via-rhine 10976 1
-----
output of /proc/ioports/
--
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial(auto)
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
0cf8-0cff : PCI conf1
1000-10ff : Adaptec AHA-7850
1000-10ff :
1400-147f : VIA Technologies, Inc. VT86C100A [Rhine 10/100]
1400-147f : via-rhine
1480-14bf : Ensoniq ES1371 [AudioPCI-97]
1480-14bf : es1371
14d0-14d3 : PCI device 1022:700c (Advanced Micro Devices [AMD])
f000-f00f : Advanced Micro Devices [AMD] AMD-765 [Viper] IDE
f000-f007 : ide0
f008-f00f : ide1
-----
output of /proc/iomem
--
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000dc000-000dcfff : Advanced Micro Devices [AMD] AMD-765 [Viper] USB
000dc000-000dcfff : usb-ohci
000e0000-000effff : Extension ROM
000f0000-000fffff : System ROM
00100000-3ffeffff : System RAM
00100000-00239bab : Kernel code
00239bac-0029531f : Kernel data
3fff0000-3ffffbff : ACPI Tables
3ffffc00-3fffffff : ACPI Non-volatile Storage
e8001000-e8001fff : Adaptec AHA-7850
e8001000-e8001fff : aic7xxx
e8002000-e800207f : VIA Technologies, Inc. VT86C100A [Rhine 10/100]
e8002000-e800207f : via-rhine
e8003000-e8003fff : PCI device 1022:700c (Advanced Micro Devices [AMD])
e9000000-e9ffffff : PCI Bus #01
e9000000-e9ffffff : nVidia Corporation NV11 (GeForce2 MX)
ec000000-efffffff : PCI device 1022:700c (Advanced Micro Devices [AMD])
f0000000-f7ffffff : PCI Bus #01
f0000000-f7ffffff : nVidia Corporation NV11 (GeForce2 MX)
fec00000-fec0ffff : reserved
fee00000-fee00fff : reserved
fff80000-ffffffff : reserved
-----
output of lspci -vvv
--
00:00.0 Host bridge: Advanced Micro Devices [AMD]: Unknown device 700c (rev 11)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 64
Region 0: Memory at ec000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at e8003000 (32-bit, prefetchable) [size=4K]
Region 2: I/O ports at 14d0 [disabled] [size=4]
Capabilities: [a0] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW+ Rate=x1,x2
Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Advanced Micro Devices [AMD]: Unknown device 700d (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 99
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: e9000000-e9ffffff
Prefetchable memory behind bridge: f0000000-f7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-765 [Viper] ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-765 [Viper] IDE (rev 01)
(prog-if 8a [Master SecP PriP])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-765 [Viper] ACPI (rev 01)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:07.4 USB Controller: Advanced Micro Devices [AMD] AMD-765 [Viper] USB (rev 07)
(prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 16 (20000ns max)
Interrupt: pin D routed to IRQ 11
Region 0: Memory at 000dc000 (32-bit, non-prefetchable) [size=4K]
00:0b.0 SCSI storage controller: Adaptec AHA-7850 (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 1000ns max), cache line size 10
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 1000 [disabled] [size=256]
Region 1: Memory at e8001000 (32-bit, non-prefetchable) [size=4K]
00:0c.0 Ethernet controller: VIA Technologies, Inc. VT86C100A [Rhine 10/100] (rev 06)
Subsystem: D-Link System Inc DFE-530TX
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 200 (29500ns min, 38000ns max), cache line size 10
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 1400 [size=128]
Region 1: Memory at e8002000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=64K]
00:0d.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 02)
Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+
<MAbort- >SERR- <PERR-
Latency: 96 (3000ns min, 32000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1480 [size=64]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
PME(D0+,D1-,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:05.0 VGA compatible controller: nVidia Corporation NV11 (rev b2) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 248 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW+ Rate=x1,x2
Command: RQ=15 SBA- AGP+ 64bit- FW- Rate=<none>
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
