Thanks for the info. I decided to take the PNY reader back, and I brought home a SanDisk dualreader SDR-77-07 (finding a -31 or a -33 reader is pretty difficult these days). Linux picked it up right away, and I was able to mount my CF card. Now the only problem is that the pictures are coming across corrupted. There appear to be bands where the colors aren't quite right, and some of the bands in the pictures themselves seem to be swapped with others. Actually to be more exact, about the top 1/3 to 1/2 of the picture is fine. The bottom portion appears to be chopped into about 4 horizontal bands. The left side of the picture appears somewhere near the middle, and some of the bands look like they're missing one of the color components R,G, or B. Any ideas about this?
I've tried mounting as msdos, vfat, and -tmsdos -ofat=12, and none of these options make a difference. This is so frustrating. Dan On Sat, 2002-07-06 at 02:05, Stephen J. Gowdy wrote: > You're the third person to have this problem recently but I've not seen a > solution yet. My SDDR-31 works fine with RH kernel 2.4.18-4. I get the > following in my logs when I plug it in; > > hub.c: USB new device connect on bus1/1, assigned device number 2 > usb.c: USB device 2 (vend/prod 0x781/0x2) is not claimed by any active > driver. > Initializing USB Mass Storage driver... > usb.c: registered new driver usb-storage > usb-uhci.c: interrupt, status 2, frame# 711 > scsi1 : SCSI emulation for USB Mass Storage devices > Vendor: SanDisk Model: ImageMate II Rev: 1.30 > Type: Direct-Access ANSI SCSI revision: 02 > WARNING: USB Mass Storage data integrity not assured > USB Mass Storage device found at 2 > USB Mass Storage support registered. > floppy0: unexpected interrupt > floppy0: sensei repl[0]=c0 repl[1]=0 > floppy0: sensei repl[0]=c1 repl[1]=0 > floppy0: sensei repl[0]=c2 repl[1]=0 > floppy0: sensei repl[0]=c3 repl[1]=0 > > (no idea why the last four lines are there... looks like something to do > with ACPI perhaps...). > > And as expected in /proc/scsi/scsi; > > [antonia] ~ > cat /proc/scsi/scsi > Attached devices: > Host: scsi1 Channel: 00 Id: 00 Lun: 00 > Vendor: SanDisk Model: ImageMate II Rev: 1.30 > Type: Direct-Access ANSI SCSI revision: 02 > > The modules that are loaded (automatically by hotplug) are; > > [antonia] ~ > lsmod > Module Size Used by Tainted: PF > usb-storage 58156 0 > > I already had these loaded; > > ide-scsi 9664 0 # prob. not relevant > ide-cd 30272 0 # prob. not relevant > sr_mod 16920 0 (autoclean) (unused) # ditto > cdrom 32192 0 (autoclean) [ide-cd sr_mod] # ditto > scsi_mod 108608 3 (autoclean) [usb-storage ide-scsi sr_mod] > usb-uhci 24484 0 (unused) > usbcore 73152 1 [usb-storage usb-uhci] > > > On Fri, 5 Jul 2002, Dan Hensley wrote: > > > I've spent several hours on this so far, and I've come to a dead end. > > According to linux-usb.org, this reader should be supported, and it > > almost seems that it is. > > > > I've made sure that I have the appropriate modules installed. The USB > > devices does list that I have the device plugged in: > > > > T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 4 Spd=12 MxCh= 0 > > D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > > P: Vendor=05e3 ProdID=0700 Rev= 1.13 > > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 96mA > > I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 > > Driver=usb-storage > > E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms > > E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms > > > > The device class is 08, which I believe should work (I know that class > > 10 does not). I've also checked /proc/scsi, and I have a directory > > usb-storage-0, with a single file "1" in it. It can tell when I have my > > reader plugged and unplugged from looking at the last line. > > > > Host scsi1: usb-storage > > Vendor: Unknown > > Product: USB Storage Device > > Serial Number: None > > Protocol: Transparent SCSI > > Transport: Bulk > > GUID: 05e307000000000000000000 > > Attached: Yes > > > > The problem seems to be though that /proc/scsi/scsi never lists the > > device. All it has is my CD-RW, which is being run by ide-scsi. As a > > result, I can't mount my card using /dev/sd[a-g]*. > > > > If anyone has some insight, I'd greatly appreciate it. I've tried using > > both uhci and usb-uhci modules, removing ide-scsi so that my CD-RW is > > not available. I'm running stock 2.4.18, and I've selected all of the > > mass-storage sub-drivers listed. I feel like I'm close, but I don't > > know what the last step is. > > > > Thanks, > > Dan > > > > > > > > > > ------------------------------------------------------- > > This sf.net email is sponsored by:ThinkGeek > > Bringing you mounds of caffeinated joy. > > http://thinkgeek.com/sf > > _______________________________________________ > > [EMAIL PROTECTED] > > To unsubscribe, use the last form field at: > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users > > > > -- > /------------------------------------+-------------------------\ > |Stephen J. Gowdy | SLAC, MailStop 34, | > |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | > |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | > |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | > \------------------------------------+-------------------------/ ------------------------------------------------------- This sf.net email is sponsored by:ThinkGeek Got root? We do. http://thinkgeek.com/sf _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
