Greetings, all.
I recently purchased an Asus Terminator (K7 version), slapped in a Duron 850 and
installed Gentoo Linux 1.2. I've been struggling ever since to get my USB devices
working.
I've built my kernel with (module) USB support, and the UHCI controller (since the
KT133 supports UHCI).
What happens is this: "modprobe usbcore" works fine, but if I "modprobe usb-uhci" I
get told "init_module: No such device." I then tried the JE driver, but "modprobe
uhci" gives me an Oops.
I've looked in the Linux-USB archives, and elsewhere, but I've not had much joy
finding a solution to my problem. I have seen, however, comments in the linux-kernel
mailing list about the KT133 chipset not being so hot.
In the interests of conserving bandwidth, I've culled my dmesg output - I've listed
from the very first USB message onwards:
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 5 for device 00:07.2
PCI: Sharing IRQ 5 with 00:07.3
uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 5 for device 00:07.3
PCI: Sharing IRQ 5 with 00:07.2
uhci.c: USB UHCI at I/O 0xd000, IRQ 5
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
ip_conntrack (895 buckets, 7160 max)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 204k freed
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x6b9/0x4061) is not claimed by any active driver.
Adding Swap: 265064k swap-space (priority -1)
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal
usb.c: unable to get major 180 for usb devices
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
8139too Fast Ethernet driver 0.9.24
PCI: Found IRQ 10 for device 00:12.0
PCI: Sharing IRQ 10 with 00:0e.0
eth0: RealTek RTL8139 Fast Ethernet at 0xc7846000, 00:e0:18:5a:49:0e, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139B'
usb-uhci.c: $Revision: 1.275 $ time 22:19:00 Jul 16 2002
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
HDLC line discipline: version $Revision: 3.3 $, maxframe=4096
N_HDLC line discipline registered.
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
After the machine has finished booting up, lsmod reveals:
Module Size Used by Not tainted
n_hdlc 6208 0 (unused)
ppp_synctty 5216 0 (unused)
ppp_generic 16204 0 [ppp_synctty]
slhc 4784 0 [ppp_generic]
nls_iso8859-1 2880 0 (unused)
nls_cp437 4384 0 (unused)
8139too 14144 1
mii 1264 0 [8139too]
usbcore 56960 1
This is from lspci -vv:
00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 81)
Subsystem: Asustek Computer, Inc.: Unknown device 8041
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 40
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: ef000000-efefffff
Prefetchable memory behind bridge: eff00000-f7ffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 80e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.2 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID): Unknown device 1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.3 USB Controller: VIA Technologies, Inc. USB (rev 1a) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID): Unknown device 1234
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Subsystem: Asustek Computer, Inc.: Unknown device 80e7
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:07.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio
Controller (rev 50)
Subsystem: Asustek Computer, Inc.: Unknown device 8072
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 12
Region 0: I/O ports at b800 [size=256]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0e.0 Modem: PCTel Inc HSP MicroModem 56 (rev 02) (prog-if 04 [Hayes/16750])
Subsystem: PCTel Inc: Unknown device 0001
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a400 [size=64]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 802f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at ee800000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: S3 Inc. ProSavage KM133 (rev 03) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 8041
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ef000000 (32-bit, non-prefetchable) [size=512K]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at efff0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=x4
For interest's sake, here's the relevant portion of dmesg when I tried the JE UHCI
module:
uhci.c: USB Universal Host Controller Interface driver v1.1
kernel BUG at slab.c:815!
invalid operand: 0000
CPU: 0
EIP: 0010:[<c0131abd>] Not tainted
EFLAGS: 00010246
eax: 00000000 ebx: c6feac20 ecx: c6feac88 edx: c6fea898
esi: c6fea892 edi: c786105a ebp: 0000003c esp: c6983ef0
ds: 0018 es: 0018 ss: 0018
Process modprobe (pid: 5021, stackpage=c6983000)
Stack: fffffff4 00000001 00000001 000062e8 c6983f0c c6feac40 00000004 00000038
c785fa90 c786104c 0000003c 00000040 00020000 00000000 00000000 c785b000
c0115a8d c6982000 48018b30 bffb828c bffb824c 000060a0 c680b000 00000060
Call Trace: [<c785fa90>] [<c786104c>] [<c0115a8d>] [<c785b060>] [<c01086f3>]
Code: 0f 0b 2f 03 bd ec 21 c0 8b 12 8b 02 0f 0d 00 81 fa 88 8a 25
I would be very grateful for any assistance you might be able to give.
Yours,
Frank Shearar
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
