hi,
I'm having problems with my digital camera via the usb-storage protocol.
Included in this email is a kernel log.
Who can I contact with questions regarding this problem?
thanks:
kernel log:
Linux version 2.4.19-rc3 (koen@delirium) (gcc version 2.95.3 20010315 (SuSE))
#1 Thu Jul 25 19:27:45 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007fe2800 (usable)
BIOS-e820: 0000000007fe2800 - 0000000008000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
127MB LOWMEM available.
Advanced speculative caching feature not present
On node 0 totalpages: 32738
zone(0): 4096 pages.
zone(1): 28642 pages.
zone(2): 0 pages.
Dell Latitude with broken BIOS detected. Refusing to enable the local APIC.
Kernel command line: BOOT_IMAGE=kernel-2.4.19 ro root=303 queit devfs=mount
Initializing CPU#0
Detected 863.887 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1723.59 BogoMIPS
Memory: 127048k/130952k available (1078k kernel code, 3516k reserved, 469k
data, 132k init, 0k highmem)
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 5, 131072 bytes)
CPU: Before vendor init, caps: 0383f9ff 00000000 00000000, vendor = 0
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 0383f9ff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) III Mobile CPU 866MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfbffe, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
PCI: Discovered primary peer bus 08 [IRQ]
PCI: Using IRQ router PIIX [8086/248c] at 00:1f.0
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 02:00.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
devfs: v1.12a (20020514) Richard Gooch ([EMAIL PROTECTED])
devfs: boot_options: 0x1
vesafb: framebuffer at 0xe0000000, mapped to 0xc8800000, size 16384k
vesafb: mode is 800x600x16, linelength=1600, pages=16
vesafb: protected mode interface info at c000:5269
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller on PCI bus 00 dev f9
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 11 for device 00:1f.1
PCI: Sharing IRQ 11 with 02:00.0
ICH3M: chipset revision 1
ICH3M: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK1517GAP, ATA DISK drive
hdc: LG CD-ROM CRN-8245B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 19640880 sectors (10056 MB), CHS=1222/255/63, UDMA(100)
hdc: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.99.newide
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
Cronyx Ltd, Synchronous PPP and CISCO HDLC (c) 1994
Linux port (c) 1998 Building Number Three Ltd & Jan "Yenya" Kasprzak.
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 129k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 132k freed
Real Time Clock Driver v1.10e
EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal
Adding Swap: 56192k swap-space (priority -1)
MSDOS FS: IO charset iso8859-15
MSDOS FS: Using codepage 850
PCI: Found IRQ 11 for device 02:00.0
PCI: Sharing IRQ 11 with 00:1f.1
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
02:00.0: 3Com PCI 3c905C Tornado at 0xec80. Vers LK1.1.16
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 02:01.0
PCI: Sharing IRQ 11 with 02:01.1
PCI: Found IRQ 11 for device 02:01.1
PCI: Sharing IRQ 11 with 02:01.0
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000010
Yenta IRQ list 06b8, PCI irq11
Socket status: 30000006
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth1: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:00:E8:15:60:D8
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
Intel 810 + AC97 Audio, version 0.21, 20:03:38 Jul 25 2002
PCI: Found IRQ 11 for device 00:1f.5
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH3 found at IO 0xdc80 and 0xd800, IRQ 11
i810_audio: Audio Controller supports 6 channels.
ac97_codec: AC97 Audio codec, id: 0x4352:0x595b (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 94M
agpgart: Detected Intel i830M chipset
agpgart: AGP aperture is 256M @ 0xd0000000
[drm] AGP 0.99 on Unknown @ 0xd0000000 256MB
[drm] Initialized radeon 1.1.1 20010405 on minor 0
SCSI subsystem driver Revision: 1.00
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 20:04:57 Jul 25 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:1d.0
PCI: Sharing IRQ 11 with 01:00.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xbf80, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF c25c9840, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: bf80
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface c25c9840
usb.c: kusbd: /sbin/hotplug add 1
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 100, change 1, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: connect-debounce failed, port 1 disabled
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 0, 12 Mb/s
hub.c: port 2, portstatus 100, change 0, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 1, 12 Mb/s
hub.c: port 1, portstatus 101, change 0, 12 Mb/s
hub.c: port 1, portstatus 101, change 0, 12 Mb/s
hub.c: port 1, portstatus 101, change 0, 12 Mb/s
hub.c: port 1, portstatus 101, change 0, 12 Mb/s
hub.c: port 1, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: kmalloc IF c25c98c0, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 2 default language ID 0x409
Manufacturer: HHH
Product: SAMSUNG DIGIMAX 130
SerialNumber: 4810816
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 83
usb-storage: Array length appears to be: 86
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xc324c660 Out: 0xc324c674 Int: 0x00000000 (Period
0)
usb-storage: New GUID 083900040000000004810816
usb-uhci.c: interrupt, status 2, frame# 1142
usb-storage: GetMaxLUN command result is 0, data is 199
usb-storage: Transport: Bulk
usb-storage: Protocol: 8070i
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 00 00 00 00 00 00
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 255 F 128 CL 12
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: command_abort() called
usb-storage: usb_stor_bulk_msg() returned -2 xferred 192/255
usb-storage: usb_stor_transfer_partial(): transfer aborted
usb-storage: Bulk data transfer result 0x3
usb-storage: -- transport indicates command was aborted
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00 00 00 00 00 00 00
usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 0 F 0 CL 12
usb-storage: command_abort() called
usb-storage: Bulk command transfer result=-2
usb-storage: -- transport indicates command was aborted
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: device_reset() called
usb-storage: Bulk reset requested
usb_control/bulk_msg: timeout
usb-storage: Bulk soft reset failed -110
usb-storage: bus_reset() called
-------------------------------------------------------
This sf.net email is sponsored by: Dice - The leading online job board
for high-tech professionals. Search and apply for tech jobs today!
http://seeker.dice.com/seeker.epl?rel_code1
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
