I believe the mechanism that parses /etc/modules.conf for those lines is a RedHat feature, but I've never used Suse so it could have it too. I meant the messages that appear on the screen during booting, but I don't know if those are the same or different for Suse. RH tells you each USB driver it loads IIRC.
On Wed, 15 Jan 2003, Carl Tuck Hartshorn wrote: > Except for the kernel, its Suse 7.3 > kernel messages with > alias usb-uhci off > > (per an earlier suggestion) > is: > > Jan 15 13:13:18 tucksLinux kernel: 02:01.0: 3Com PCI 3c905C_1 Tornado at > 0xb000. Vers LK1.1.18-ac > Jan 15 13:13:21 tucksLinux usbmgr[332]: start 0.4.6 > Jan 15 13:13:21 tucksLinux kernel: usb.c: registered new driver usbdevfs > Jan 15 13:13:21 tucksLinux kernel: usb.c: registered new driver hub > Jan 15 13:13:21 tucksLinux kernel: usb.c: registered new driver hid > Jan 15 13:13:21 tucksLinux kernel: hid-core.c: v1.8.1 Andreas Gal, Vojtech > Pavlik <[EMAIL PROTECTED]> > Jan 15 13:13:21 tucksLinux kernel: hid-core.c: USB HID support drivers > Jan 15 13:13:21 tucksLinux kernel: mice: PS/2 mouse device common for all mice > Jan 15 13:13:21 tucksLinux usbmgr[334]: "hid" was loaded > Jan 15 13:13:21 tucksLinux usbmgr[334]: "mousedev" was loaded > Jan 15 13:13:21 tucksLinux usbmgr[334]: "usb-uhci" was loaded > Jan 15 13:13:21 tucksLinux usbmgr[393]: mount /proc/bus/usb > > > > I upgraded to an Asus A7N8X with two USB controllers and one USB2. > > > At the moment, I have only a APC backup plugged in. > > > > > > The previous system--nonUSB2--had no problem. It detected and found the > > > APC. > > > > > > my 'modules.conf' (today) has > > > > > > alias usb usb-ohci > > > alias usb-controller usb-ohci > > > alias usb-controller1 usb-ohci > > > alias usb-controller2 ehci-hcd > > > > > > When the system boots, lsmod only shows... > > > > > > Module Size Used by Not tainted > > > ncr53c8xx 51840 2 (autoclean) > > > st 26164 2 (autoclean) > > > mousedev 3872 0 (unused) > > > hid 13088 0 (unused) > > > input 3072 0 [mousedev hid] > > > usbcore 54016 1 [hid] > > > > > > > > > dmesg seems to be OK but I dont if I'm reading this well... > > > usb.c: registered new driver usbdevfs > > > usb.c: registered new driver hub > > > usb-uhci.c: $Revision: 1.275 $ time 19:15:44 Jan 12 2003 > > > usb-uhci.c: High bandwidth mode enabled > > > usb-uhci.c: v1.275:USB Universal Host Controller Interface driver > > > usb.c: deregistering driver usbdevfs > > > usb.c: deregistering driver hub > > > usb.c: registered new driver usbdevfs > > > usb.c: registered new driver hub > > > usb.c: registered new driver hid > > > hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> > > > hid-core.c: USB HID support drivers > > > > > > > > > but the boot log shows: > > > > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: registered new driver usbdevfs > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: registered new driver hub > > > Jan 14 15:24:52 tucksLinux kernel: usb-uhci.c: $Revision: 1.275 $ time > > > 19:15:44 Jan 12 2003 > > > Jan 14 15:24:52 tucksLinux kernel: usb-uhci.c: High bandwidth mode > > > enabled Jan 14 15:24:52 tucksLinux kernel: usb-uhci.c: v1.275:USB > > > Universal Host Controller Interface driver > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: deregistering driver usbdevfs > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: deregistering driver hub > > > Jan 14 15:24:52 tucksLinux usbmgr[340]: start 0.4.6 > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: registered new driver usbdevfs > > > Jan 14 15:24:52 tucksLinux kernel: usb.c: registered new driver hub > > > Jan 14 15:24:53 tucksLinux kernel: usb.c: registered new driver hid > > > Jan 14 15:24:53 tucksLinux kernel: hid-core.c: v1.8.1 Andreas Gal, > > > Vojtech Pavlik <[EMAIL PROTECTED]> > > > Jan 14 15:24:53 tucksLinux kernel: hid-core.c: USB HID support drivers > > > Jan 14 15:24:53 tucksLinux kernel: mice: PS/2 mouse device common for all > > > mice Jan 14 15:24:53 tucksLinux usbmgr[342]: "hid" was loaded > > > Jan 14 15:24:53 tucksLinux usbmgr[342]: "mousedev" was loaded > > > Jan 14 15:24:53 tucksLinux kernel: usb-uhci.c: $Revision: 1.275 $ time > > > 19:15:44 Jan 12 2003 > > > Jan 14 15:24:53 tucksLinux kernel: usb-uhci.c: High bandwidth mode > > > enabled Jan 14 15:24:53 tucksLinux kernel: usb-uhci.c: v1.275:USB > > > Universal Host Controller Interface driver > > > Jan 14 15:24:53 tucksLinux insmod: > > > /lib/modules/2.4.20-ac2/kernel/drivers/usb/usb-uhci.o: init_module: No > > > such device > > > Jan 14 15:24:53 tucksLinux insmod: Hint: insmod errors can be caused by > > > incorrect module parameters, including invalid > > > IO or IRQ parameters > > > Jan 14 15:24:53 tucksLinux insmod: > > > /lib/modules/2.4.20-ac2/kernel/drivers/usb/usb-uhci.o: insmod > > > /lib/modules/2.4.20-ac > > > 2/kernel/drivers/usb/usb-uhci.o failed > > > Jan 14 15:24:53 tucksLinux insmod: > > > /lib/modules/2.4.20-ac2/kernel/drivers/usb/usb-uhci.o: insmod usb-uhci > > > failed Jan 14 15:24:53 tucksLinux usbmgr[342]: "usb-uhci" was loaded > > > Jan 14 15:24:53 tucksLinux usbmgr[401]: mount /proc/bus/usb > > > > > > So, I think the modules.conf has errors but I've tried enough > > > combinations (but not > > > the right one). > > > > > > At this point, usbtree shows nil. > > > > > > If I manually do: > > > > > > modprobe usb-ohci > > > modprobe ehci-hcd > > > > > > and then, usbtree shows: > > > > > > /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ehci-hcd/6p, 480M > > > /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=usb-ohci/3p, 12M > > > > > > |__ Port 2: Dev 3, If 0, Class=HID, Driver=hid, 1.5M > > > > > > /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=usb-ohci/3p, 12M > > > > > > and dmesg shows > > > > > > usb-ohci.c: USB OHCI at membase 0xd08f0000, IRQ 5 > > > usb-ohci.c: usb-00:02.0, PCI device 10de:0067 > > > usb.c: new USB bus registered, assigned bus number 1 > > > hub.c: USB hub found > > > hub.c: 3 ports detected > > > PCI: Setting latency timer of device 00:02.1 to 64 > > > usb-ohci.c: USB OHCI at membase 0xd08f2000, IRQ 11 > > > usb-ohci.c: usb-00:02.1, PCI device 10de:0067 > > > usb.c: new USB bus registered, assigned bus number 2 > > > hub.c: USB hub found > > > hub.c: 3 ports detected > > > hub.c: new USB device 00:02.1-2, assigned address 2 > > > > > > : USB HID v1.00 Joystick [American Power Conversion Back-UPS 500 FW: > > > : 6.1.D USB > > > > > > FW: c1 ] on usb2:2.0 > > > PCI: Setting latency timer of device 00:02.2 to 64 > > > hcd.c: ehci-hcd @ 00:02.2, PCI device 10de:0068 > > > hcd.c: irq 5, pci mem d08f9000 > > > usb.c: new USB bus registered, assigned bus number 3 > > > ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0 > > > usb.c: USB disconnect on device 00:02.1-2 address 2 > > > hub.c: USB hub found > > > hub.c: 6 ports detected > > > hub.c: new USB device 00:02.1-2, assigned address 3 > > > > > > : USB HID v1.00 Joystick [American Power Conversion Back-UPS 500 FW: > > > : 6.1.D USB > > > > > > FW: c1 ] on usb2:3.0 > > > > > > > > > > > > So, can somebody spot something? > > > > > > > > > One more thing, 2.4.20-ac2 > > > > > > > > > Thanks, > > > > > > Tuck Hartshorn > > > > > > > > > > > > > > > ------------------------------------------------------- > > > This SF.NET email is sponsored by: Take your first step towards giving > > > your online business a competitive advantage. Test-drive a Thawte SSL > > > certificate - our easy online guide will show you how. Click here to get > > > started: http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0027en > > > _______________________________________________ > > > [EMAIL PROTECTED] > > > To unsubscribe, use the last form field at: > > > https://lists.sourceforge.net/lists/listinfo/linux-usb-users > -- /------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/ ------------------------------------------------------- This SF.NET email is sponsored by: A Thawte Code Signing Certificate is essential in establishing user confidence by providing assurance of authenticity and code integrity. Download our Free Code Signing guide: http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0028en _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
