BTW, I'm sorry everyone received html but this user really tried to avoid it (I think this was the fifth attempt).
On Mon, 14 Jul 2003 [EMAIL PROTECTED] wrote: > Help, > > I am not able to get USB 2.0 under Linux (RH7.2 &2.4.21.pre6 kernel) to work > with an external hard drive, consistently . After rebooting several times, > un-plugging, and re-plugging the external USB drive and the stars aligning, I > can access the external drive, but that wears me out. It's not consistent. > > This is a IBM T23 Thinkpad with a BusLink USB 2.0 Cardbus and an In-System > Design (ISD) external box containing an IBM 120 GB hard drive, split into a fat > and a linux partition. > > The ISD always shows up in /proc/bus/usb/devices, which is shown below. But > when I try to mount the partitions, results vary. Sometimes it works, but > other times the system hangs or I get the following: > > mount /mnt/usbWin1 => mount: /dev/sda1 is not a valid block device > > mount /mnt/usbLin1 => mount: /dev/sda5 is not a valid block device > > /sbin/fdisk /dev/sda may respond correctly, hang, or say “unable to > read /dev/sda” > > Any would be greatly appreciated.! > > Thanks, > > Jim > > > Here are /proc/scsi/scsi and proc/bus/usb/devices > > /proc/scsi/scsi > Attached devices: > Host: scsi0 Channel: 00 Id: 00 Lun: 00 > Vendor: IC35L120 Model: AVVA07-0 Rev: VA6O > Type: Direct-Access ANSI SCSI revision: 02 > > /proc/bus/usb/devices > T: Bus=06 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 5 > B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 2.04 > S: Manufacturer=Linux 2.4.21-pre6 ehci-hcd > S: Product=PCI device 1033:00e0 > S: SerialNumber=03:00.2 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms > > T: Bus=06 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 > D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 > P: Vendor=05ab ProdID=0060 Rev=11.06 > S: Manufacturer=In-System Design > S: Product=USB Storage Adapter > S: SerialNumber=11100E000041C108 > C:* #Ifs= 1 Cfg#= 2 Atr=c0 MxPwr= 98mA > I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage > E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us > E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms > E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=32ms > > T: Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB OHCI Root Hub > S: SerialNumber=e092f000 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms > > T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3 > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB OHCI Root Hub > S: SerialNumber=e0926000 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms > > T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB UHCI Root Hub > S: SerialNumber=1840 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms > > T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 93/900 us (10%), #Int= 1, #Iso= 0 > D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB UHCI Root Hub > S: SerialNumber=1820 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms > > T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0 > D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=04b4 ProdID=0001 Rev= 0.00 > C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbmouse > E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=10ms > > T: Bus=02 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 > D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 > P: Vendor=1404 ProdID=cddc Rev= 1.00 > S: Manufacturer=Fundamental Software Inc. > S: Product=FSI Dongle > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA > I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=serial > E: Ad=81(I) Atr=02(Bulk) MxPS= 16 Ivl=0ms > E: Ad=01(O) Atr=02(Bulk) MxPS= 16 Ivl=0ms > > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 > D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 > P: Vendor=0000 ProdID=0000 Rev= 0.00 > S: Product=USB UHCI Root Hub > S: SerialNumber=1800 > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255m > -- /------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/ ------------------------------------------------------- This SF.Net email sponsored by: Parasoft Error proof Web apps, automate testing & more. Download & eval WebKing and get a free book. www.parasoft.com/bulletproofapps1 _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
