Hello,
I use kernel 2.6.5-rc2 and have an external USB-Case for 2,5" HDD with the
GL811USB Chip. When attaching the first time, everything is fine, but when
disconnecting and attaching the second time there's no reaction. I found
out, that after having connected the device for the first time, it is no
longer
possible to remove the ehci-hcd module.
Here my steps:
1. normally load the usb-modules (I am using the hotplug script from gentoo
2004.0)
2. connected the device
3. disconnected the device.
4. Connected it again (same USB-Port or different USB-Port), no reaction at
all
5. tried to remove the modules, rmmod usb-storage works, rmmod ehci-hcd
hangs
My hardware: Fujitsu Siemens Amilo D 8830 Laptop. Intel P4 2,8Ghz, no
Hyperthreading, Intel i845 Chipset, USB 2.0 onboard.
Here the output of lspci, AFTER having invoked rmmod ehci-hcd (the command
still hangs):
Module Size Used by
sd_mod 15872 0
radeon 106412 0
sg 29472 0
parport_pc 35008 1
lp 9156 0
parport 35400 2 parport_pc,lp
ds 14084 2
pppoe 10944 2
pppox 2952 1 pppoe
ipv6 222528 8
af_packet 17160 2
ppp_generic 23316 6 pppoe,pppox
slhc 6528 1 ppp_generic
ohci_hcd 28676 0
uhci_hcd 29836 0
eth1394 17544 0
ehci_hcd 35844 0
snd_intel8x0 30120 0
snd_ac97_codec 60164 1 snd_intel8x0
gameport 3712 1 snd_intel8x0
snd_mpu401_uart 6272 1 snd_intel8x0
snd_rawmidi 20128 1 snd_mpu401_uart
8250_pci 15616 0
8250 18592 1 8250_pci
serial_core 19584 1 8250
yenta_socket 14336 0
pcmcia_core 56756 2 ds,yenta_socket
ohci1394 31364 0
ieee1394 92088 2 eth1394,ohci1394
usbcore 99036 5 ohci_hcd,uhci_hcd,ehci_hcd
snd_seq_oss 31488 0
snd_seq_midi_event 6272 1 snd_seq_oss
snd_seq 50576 4 snd_seq_oss,snd_seq_midi_event
snd_seq_device 6536 3 snd_rawmidi,snd_seq_oss,snd_seq
snd_pcm_oss 48292 0
snd_pcm 83364 2 snd_intel8x0,snd_pcm_oss
snd_page_alloc 8964 2 snd_intel8x0,snd_pcm
snd_timer 21380 2 snd_seq,snd_pcm
snd_mixer_oss 17280 1 snd_pcm_oss
snd 46436
12
snd_intel8x0,snd_ac97_codec,snd_mpu401_uart,snd_rawmidi,snd_seq_oss,snd_seq_midi_event,snd_seq,snd_seq_device,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore 7648 1 snd
evdev 7936 1
natsemi 21856 0
fakephp 3332 0
pci_hotplug 10372 1 fakephp
ide_tape 34128 0
st 37660 0
ide_cd 36996 0
sr_mod 13220 0
scsi_mod 66752 4 sd_mod,sg,st,sr_mod
cdrom 37664 2 ide_cd,sr_mod
Here the output of lspci -vvv
00:00.0 Host bridge: Intel Corp. 82845G/GL[Brookdale-G]/GE/PE DRAM
Controller/Host-Hub Interface (rev 03)
Subsystem: Unknown device 1734:102a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [6105]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-
Rate=<none>
lspci: stack smashing attack in function show_capsAborted
I don't know whats happening here. This error even occurs after having
rebooted. This should not be your problem
Here the debug output to /var/log/messages with usb-storage-debug and
usb-debug on:
Mar 23 15:22:13 lapp31000 ehci_hcd 0000:00:1d.7: GetStatus port 5 status
001803 POWER sig=j CSC CONNECT
Mar 23 15:22:13 lapp31000 hub 1-0:1.0: port 5, status 501, change 1, 480
Mb/s
Mar 23 15:22:13 lapp31000 hub 1-0:1.0: debounce: port 5: delay 100ms stable
4 st atus 0x501
Mar 23 15:22:13 lapp31000 ehci_hcd 0000:00:1d.7: port 5 high speed
Mar 23 15:22:13 lapp31000 ehci_hcd 0000:00:1d.7: GetStatus port 5 status
001005 POWER sig=se0 PE CONNECT
Mar 23 15:22:13 lapp31000 usb 1-5: new high speed USB device using address 2
Mar 23 15:22:13 lapp31000 usb 1-5: new device strings: Mfr=2, Product=3,
SerialN umber=0
Mar 23 15:22:13 lapp31000 drivers/usb/core/message.c: USB device number 2
defaul t language ID 0x409
Mar 23 15:22:13 lapp31000 usb 1-5: Product: USB CF Reader
Mar 23 15:22:13 lapp31000 usb 1-5: Manufacturer: Genesyslogic
Mar 23 15:22:13 lapp31000 drivers/usb/core/usb.c: usb_hotplug
Mar 23 15:22:13 lapp31000 usb 1-5: registering 1-5:1.0 (config #1, interface
0)
Mar 23 15:22:13 lapp31000 drivers/usb/core/usb.c: usb_hotplug
Mar 23 15:22:13 lapp31000 Initializing USB Mass Storage driver...
Mar 23 15:22:13 lapp31000 usb-storage 1-5:1.0: usb_probe_interface
Mar 23 15:22:13 lapp31000 usb-storage 1-5:1.0: usb_probe_interface - got id
Mar 23 15:22:13 lapp31000 usb-storage: USB Mass Storage device detected
Mar 23 15:22:13 lapp31000 usb-storage: altsetting is 0, id_index is 118
Mar 23 15:22:13 lapp31000 usb-storage: -- associate_dev
Mar 23 15:22:13 lapp31000 usb-storage: Transport: Bulk
Mar 23 15:22:13 lapp31000 usb-storage: Protocol: Transparent SCSI
Mar 23 15:22:13 lapp31000 usb-storage: Endpoints: In: 0xeb271d00 Out:
0xeb271d14 Int: 0x00000000 (Period 0)
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_control_msg: rq=fe rqtype=a1
val ue=0000 index=00 len=1
Mar 23 15:22:13 lapp31000 usb-storage: GetMaxLUN command result is 1, data
is 0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 scsi0 : SCSI emulation for USB Mass Storage
devices
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command INQUIRY (6 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 12 00 00 00 24 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0x1 L 36
F 12 8 Trg 0 LUN 0 CL 6
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 36
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 36/36
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk data transfer result 0x0
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0x1 R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: Fixing INQUIRY data to show SCSI rev
2 - was 0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command INQUIRY (6 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 12 00 00 00 25 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0x2 L 37
F 12 8 Trg 0 LUN 0 CL 6
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 37
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 36/37
Mar 23 15:22:13 lapp31000 usb-storage: -- short transfer
Mar 23 15:22:13 lapp31000 usb-storage: Bulk data transfer result 0x1
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0x2 R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: Fixing INQUIRY data to show SCSI rev
2 - was 0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 Vendor: HITACHI_ Model: DK23CA-20 Rev:
0811
Mar 23 15:22:13 lapp31000 Type: Direct-Access ANSI
SCSI r evision: 02
Mar 23 15:22:13 lapp31000 Attached scsi generic sg0 at scsi0, channel 0, id
0, l un 0, type 0
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad LUN (0:1)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (1:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (2:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (3:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (4:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (5:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (6:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Bad target number (7:0)
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x40000
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 USB Mass Storage device found at 2
Mar 23 15:22:13 lapp31000 drivers/usb/core/usb.c: registered new driver
usb-stor age
Mar 23 15:22:13 lapp31000 USB Mass Storage support registered.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 scsi.agent[5642]: disk at
/devices/pci0000:00/0000:00: 1d.7/usb1/1-5/1-5:1.0/host0/0:0:0:0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command TEST_UNIT_READY (6 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 00 00 00 00 00 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F
0 T rg 0 LUN 0 CL 6
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0xb R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command READ_CAPACITY (10 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 25 00 00 00 00 00 00 00 00 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0xc L 8 F
128 Trg 0 LUN 0 CL 10
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 8
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 8/8
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk data transfer result 0x0
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0xc R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 SCSI device sda: 39070080 512-byte hdwr sectors
(20004 MB)
Mar 23 15:22:13 lapp31000 sda: assuming drive cache: write through
Mar 23 15:22:13 lapp31000 /dev/scsi/host0/bus0/target0/lun0:<7>usb-storage:
queu ecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command READ_10 (10 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 28 00 00 00 00 00 00 00 08 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0xd L
4096 F 128 Trg 0 LUN 0 CL 10
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_sglist: xfer
4096 bytes, 1 entries
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 4096/4096
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk data transfer result 0x0
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0xd R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:13 lapp31000 usb-storage: queuecommand called
Mar 23 15:22:13 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:13 lapp31000 usb-storage: Command READ_10 (10 bytes)
Mar 23 15:22:13 lapp31000 usb-storage: 28 00 02 54 29 78 00 00 08 00
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Command S 0x43425355 T 0xe L
4096 F 128 Trg 0 LUN 0 CL 10
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 31
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 31/31
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk command transfer result=0
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_sglist: xfer
4096 bytes, 1 entries
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 4096/4096
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk data transfer result 0x0
Mar 23 15:22:13 lapp31000 usb-storage: Attempting to get CSW...
Mar 23 15:22:13 lapp31000 usb-storage: usb_stor_bulk_transfer_buf: xfer 13
bytes
Mar 23 15:22:13 lapp31000 usb-storage: Status code 0; transferred 13/13
Mar 23 15:22:13 lapp31000 usb-storage: -- transfer complete
Mar 23 15:22:13 lapp31000 usb-storage: Bulk status result = 0
Mar 23 15:22:13 lapp31000 usb-storage: Bulk Status S 0x53425355 T 0xe R 0
Stat 0 x0
Mar 23 15:22:13 lapp31000 usb-storage: scsi cmd done, result=0x0
Mar 23 15:22:13 lapp31000 p1 p2
Mar 23 15:22:13 lapp31000 Attached scsi disk sda at scsi0, channel 0, id 0,
lun 0
Mar 23 15:22:13 lapp31000 usb-storage: *** thread sleeping.
Mar 23 15:22:24 lapp31000 ehci_hcd 0000:00:1d.7: GetStatus port 5 status
001002 POWER sig=se0 CSC
Mar 23 15:22:24 lapp31000 hub 1-0:1.0: port 5, status 100, change 1, 12 Mb/s
Mar 23 15:22:24 lapp31000 usb 1-5: USB disconnect, address 2
Mar 23 15:22:24 lapp31000 usb 1-5: usb_disable_device nuking all URBs
Mar 23 15:22:24 lapp31000 usb 1-5: unregistering interface 1-5:1.0
Mar 23 15:22:24 lapp31000 usb-storage: storage_disconnect() called
Mar 23 15:22:24 lapp31000 usb-storage: usb_stor_stop_transport called
Mar 23 15:22:24 lapp31000 usb-storage: -- dissociate_dev
Mar 23 15:22:24 lapp31000 usb-storage: -- sending exit command to thread
Mar 23 15:22:24 lapp31000 usb-storage: *** thread awakened.
Mar 23 15:22:24 lapp31000 usb-storage: -- exit command received
Mar 23 15:22:24 lapp31000 usb-storage: -- usb_stor_release_resources
finished
Mar 23 15:22:24 lapp31000 drivers/usb/core/usb.c: usb_hotplug
Mar 23 15:24:42 lapp31000 usb-storage: usb_stor_exit() called
Mar 23 15:24:42 lapp31000 usb-storage: -- calling usb_deregister()
Mar 23 15:24:42 lapp31000 drivers/usb/core/usb.c: deregistering driver
usb-stora ge
Mar 23 15:25:12 lapp31000 ehci_hcd 0000:00:1d.7: remove, state 1
Mar 23 15:25:12 lapp31000 ehci_hcd 0000:00:1d.7: roothub graceful disconnect
Mar 23 15:25:12 lapp31000 usb usb1: USB disconnect, address 1
Mar 23 15:25:12 lapp31000 usb usb1: usb_disable_device nuking all URBs
Mar 23 15:25:12 lapp31000 ehci_hcd 0000:00:1d.7: shutdown urb f5650300 pipe
4040 8180 ep1in-intr
Mar 23 15:25:12 lapp31000 usb usb1: unregistering interface 1-0:1.0
I hope having provided all necessary information.
Greetings
-Daniel
--
+++ NEU bei GMX und erstmalig in Deutschland: T�V-gepr�fter Virenschutz +++
100% Virenerkennung nach Wildlist. Infos: http://www.gmx.net/virenschutz
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials
Free Linux tutorial presented by Daniel Robbins, President and CEO of
GenToo technologies. Learn everything from fundamentals to system
administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
