Hi Jeremy,
You must have USB disabled in the BIOS for it not to show up on
lspci. I'm assuming you do have USB ports that are connected to
something....
regards,
Stephen.
On Tue, 13 Apr 2004, Jeremy C. Reed wrote:
> On Tue, 13 Apr 2004, Stephen J. Gowdy wrote:
>
> > I'd use modules. Actually looking over your earlier mail I now see it did
> > load them. However, it didn't find any hardware. Can you get lspci?, this
> > time don't grep though, send the whole output. You proabbly don't have the
> > hardware enabled in your BIOS or it isn't getting an interupt line (but
> > for the latter I'd expected some output in your kernel log).
>
> I realized that a lspci was available for me. (I use pkgsrc[1] for my
> entire Linux system and I thought I would have to package pciutils, but I
> found it was already available at pkgsrc/sysutils/pciutils/.)
>
> Here is the output (and grep didn't see any "HCI"):
>
> 00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller
> Hub (rev 04)
> Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controller Hub
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ >SERR- <PERR-
> Latency: 0
> Capabilities: [88] #09 [f104]
>
> 00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics
> Controller] (rev 04) (prog-if 00 [VGA])
> Subsystem: Micro-star International Co Ltd: Unknown device 3518
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
> Region 1: Memory at eff00000 (32-bit, non-prefetchable) [size=512K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB PCI Bridge (rev 05) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
> I/O behind bridge: 0000a000-0000afff
> Memory behind bridge: efa00000-efcfffff
> Prefetchable memory behind bridge: e7800000-e78fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
>
> 00:1f.0 ISA bridge: Intel Corp. 82801BA ISA Bridge (LPC) (rev 05)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:1f.1 IDE interface: Intel Corp. 82801BA IDE U100 (rev 05) (prog-if 80 [Master])
> Subsystem: Micro-star International Co Ltd: Unknown device 3510
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Region 4: I/O ports at ffa0 [size=16]
>
> 00:1f.3 SMBus: Intel Corp. 82801BA/BAM SMBus (rev 05)
> Subsystem: Micro-star International Co Ltd: Unknown device 3510
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 11
> Region 4: I/O ports at 0540 [size=16]
>
> 00:1f.5 Multimedia audio controller: Intel Corp. 82801BA/BAM AC'97 Audio (rev 05)
> Subsystem: Micro-star International Co Ltd: Unknown device 3510
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping-
> SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 11
> Region 0: I/O ports at dc00 [size=256]
> Region 1: I/O ports at d800 [size=64]
>
> 01:08.0 Ethernet controller: Intel Corp. 82801BA/BAM/CA/CAM Ethernet Controller (rev
> 03)
> Subsystem: Intel Corp. EtherExpress PRO/100 VM
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping-
> SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min, 14000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at efc00000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at ac00 [size=64]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
>
>
> It's a cheap box, and I have two of them.
>
> Later I'll try modules, but I am unclear how that would differ especially
> since the support is available to be configured and built as built-in.
>
> I appreciate your time, Stephen.
>
> Thank you,
>
> Jeremy C. Reed
> http://www.reedmedia.net/
>
> [1] pkgsrc is a portable package building system for Linux, NetBSD, Darwin,
> Mac OS X, Irix, SunOS/Solaris, AIX, HPUX, BSD/OS, FreeBSD, Windows and
> other operating systems for managing nearly 5000 software suites. It
> provides: 1) a categorized collection of specifications that help automate
> fetching, checking checksums, patching, configuring, building, installing
> and packaging software suites; 2) package installation and maintenance
> tools (like pkg_add, pkg_info, pkg_delete and others).
>
> p.s. Anyone local to the Pacific Northwest (Washington state and lower
> British Columbia)? This Saturday is the 5th annual Linux Fest Northwest
> with over 40 free lectures, booths and over 1200 expected to attend. I am
> giving a lecture on pkgsrc there.
>
--
/------------------------------------+-------------------------\
|Stephen J. Gowdy | SLAC, MailStop 34, |
|http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, |
|http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA |
|EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 |
\------------------------------------+-------------------------/
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials
Free Linux tutorial presented by Daniel Robbins, President and CEO of
GenToo technologies. Learn everything from fundamentals to system
administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
