Yesterday I posted this result of "lsusb" in SuSE 9 to show the "fc01" of the 250Gb drive
Bus 005 Device 003: ID 0d49:3000 Maxtor Bus 005 Device 002: ID 07ab:fccd Freecom Technologies Bus 005 Device 001: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 002: ID 07ab:fc01 Freecom Technologies IDE bridge
Bus 001 Device 001: ID 0000:0000
Today I booted SuSE with no USB devices, then plugged in the 250Gb drive:-
Bus 005 Device 002: ID 07ab:fccd Freecom Technologies Bus 005 Device 001: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 001: ID 0000:0000
So, I'm sorry, my CD-RW is "fc01" and my client's 250Gb id "fccd", just like Eero's 160Gb.
The "IDE bridge" is not only confusing to me, it seems to trigger usb-storage unnecessarily for the CD-RW:-
usb 1-1: new full speed USB device using address 2 Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices Vendor: TEAC Model: CD-W54E Rev: 1.1B Type: CD-ROM ANSI SCSI revision: 02 sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 5 USB Mass Storage device found at 2 usbcore: registered new driver usb-storage USB Mass Storage support registered.
While the 250Gb in SuSE9 consistantly fails at scsi level, locking any attempt to "cat /proc/bus/usb/devices" (odd number of sectors):-
usb 5-1: new high speed USB device using address 2 usb 5-1: Product: FHD-Classic usb 5-1: Manufacturer: Freecom Technologies usb 5-1: SerialNumber: 10000000000000000CA89 Initializing USB Mass Storage driver... usb 5-1: control timeout on ep0in scsi0 : SCSI emulation for USB Mass Storage devices Vendor: HDS72252 Model: 5VLAT80 Rev: V36O Type: Direct-Access ANSI SCSI revision: 02 SCSI device sda: 488397169 512-byte hdwr sectors (250059 MB) sda: assuming drive cache: write through sda:SCSI error : <0 0 0 0> return code = 0x70000 end_request: I/O error, dev sda, sector 488397168 Buffer I/O error on device sda, logical block 488397168
Back in Fedora2 with verbose, Alan Stern patched kernel, the GetMaxLUN fails -71 and it gives up quickly:-
ehci_hcd 0000:00:0d.2: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 hub 1-0:1.0: port 1 not reset yet, waiting 50ms ehci_hcd 0000:00:0d.2: port 1 high speed ehci_hcd 0000:00:0d.2: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT usb 1-1: new high speed USB device using address 2 usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: default language 0x0409 usb 1-1: Product: FHD-Classic usb 1-1: Manufacturer: Freecom Technologies usb 1-1: SerialNumber: 10000000000000000CA89 usb 1-1: hotplug usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: hotplug usb-storage 1-1:1.0: usb_probe_interface usb-storage 1-1:1.0: usb_probe_interface - got id usb-storage: USB Mass Storage device detected usb-storage: altsetting is 0, id_index is 72 usb-storage: -- associate_dev usb-storage: Vendor: Freecom Technologies usb-storage: Product: FHD-Classic usb 1-1: control timeout on ep0in ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes usb-storage: Transport: Bulk usb-storage: Protocol: Transparent SCSI usb-storage: Endpoints: In: 0xcc6d6474 Out: 0xcc6d6460 Int: 0x00000000 (Period 0) usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 ehci_hcd 0000:00:0d.2: devpath 1 ep0in 3strikes usb-storage: GetMaxLUN command result is -71, data is 0 usb-storage: storage_probe() failed usb-storage: -- usb_stor_release_resources usb-storage: -- dissociate_dev usb-storage: probe of 1-1:1.0 failed with error -1
However, when the Maxtor HDD is connected, it goes back to probing the Freecom 250Gb:-
ehci_hcd 0000:00:0d.2: GetStatus port 2 status 001803 POWER sig=j CSC CONNECT
hub 1-0:1.0: port 2, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x501
hub 1-0:1.0: port 2 not reset yet, waiting 50ms
ehci_hcd 0000:00:0d.2: port 2 high speed
ehci_hcd 0000:00:0d.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
usb 1-2: new high speed USB device using address 3
usb 1-2: new device strings: Mfr=73, Product=90, SerialNumber=110
usb 1-2: default language 0x0409
usb 1-2: Product: Maxtor USB Drive usb 1-2: Manufacturer: Maxtor usb 1-2: SerialNumber: 1200E000022241307
usb 1-2: hotplug
usb 1-2: adding 1-2:2.0 (config #2, interface 0)
usb 1-2:2.0: hotplug
usb-storage 1-2:2.0: usb_probe_interface
usb-storage 1-2:2.0: usb_probe_interface - got id
usb-storage: USB Mass Storage device detected
usb-storage: altsetting is 0, id_index is 123
usb-storage: -- associate_dev
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: Endpoints: In: 0xcec9c8f4 Out: 0xcec9c8e0 Int: 0xcec9c908 (Period 9)
usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1
usb-storage: GetMaxLUN command result is 1, data is 0
usb-storage: *** thread sleeping.
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 24 00
usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 36 bytes
usb-storage: Status code 0; transferred 36/36
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0
usb-storage: Fixing INQUIRY data to show SCSI rev 2 - was 0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
Vendor: Maxtor 4 Model: G120J6 Rev: GAK8
Type: Direct-Access ANSI SCSI revision: 02
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x2 L 0 F 0 Trg 0 LUN 0 CL 6
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x2 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_CAPACITY (10 bytes)
usb-storage: 25 00 00 00 00 00 00 00 00 00
usb-storage: Bulk Command S 0x43425355 T 0x3 L 8 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_buf: xfer 8 bytes
usb-storage: Status code 0; transferred 8/8
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x3 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
SCSI device sda: 240121728 512-byte hdwr sectors (122942 MB)
sda: assuming drive cache: write through
sda:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x4 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x4 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage: 28 00 0e 4f f7 78 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x5 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
USB Mass Storage device found at 3
Likewise at any other USB connection or disconnection, while without the 250Gb connected, the dmesg output is much shorter.
Is the GetMaxLUN (or whatever) fixable?
------------------------------------------------------- This SF.net email is sponsored by: IT Product Guide on ITManagersJournal Use IT products in your business? Tell us what you think of them. Give us Your Opinions, Get Free ThinkGeek Gift Certificates! Click to find out more http://productguide.itmanagersjournal.com/guidepromo.tmpl _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
