usb 1-4: new high speed USB device using ehci_hcd and address 4On Sat, 4 Dec 2004, Dietrich Foethke wrote:
Hello,
it took a while, but finally I tried to fix the problem with the two methods you told me. Here's the results:
As reported before, doing
echo 'Sony:DSC - F505:0x80400' >/proc/scsi/device_info
works fine for both, 2.6.8 and 2.6.9 kernels,
That's a good start.
BUT only if the kernel option
CONFIG_USB_STORAGE_RW_DETECT is not set! If this option is set, mounting the camera fails with the same errors described before.
That's why RW_DETECT was left as a configuration option, so that people could turn it off if they have buggy devices. Although perhaps making it a module parameter instead would be a better approach...
How did you realize that the RW_DETECT setting was causing a problem?
Furthermore there's a problem with the "haldaemon" that's started by
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
eth0: link down
usb 1-4: khubd timed out on ep0in
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
eth1: resetting device...
eth1: uploading firmware...
eth1: firmware version: 1.0.4.3
eth1: firmware upload complete
eth1: interface reset complete
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
Bluetooth: Core ver 2.7
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.6
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM ver 1.3
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
parport_pc: Ignoring new-style parameters in presence of obsolete ones
lp: driver loaded but no devices found
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
cfq: depth 4 reached, tagging now on
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
mtrr: 0x90000000,0x2000000 overlaps existing 0x90000000,0x1000000
usb 1-4: USB disconnect, address 4
usb 1-4: new high speed USB device using ehci_hcd and address 5
usb 1-4: 05-wait_for_sys timed out on ep0in
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
usb 1-4: reset high speed USB device using ehci_hcd and address 5
usb 1-4: scsi_eh_1 timed out on ep0out
usb 1-4: failed to restore interface 0 altsetting 0 (error=-110)
scsi: Device offlined - not ready after error recovery: host 1 channel 0 id 0 lun 0
SCSI error : <1 0 0 0> return code = 0x50000
usb 1-4: USB disconnect, address 5
usb 1-4: new high speed USB device using ehci_hcd and address 6
usb 1-4: device descriptor read/64, error -71
usb 1-4: 05-wait_for_sys timed out on ep0in
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi2, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-4: reset high speed USB device using ehci_hcd and address 6
usb 1-4: scsi_eh_2 timed out on ep0out
usb 1-4: failed to restore interface 0 altsetting 0 (error=-110)
scsi: Device offlined - not ready after error recovery: host 2 channel 0 id 0 lun 0
SCSI error : <2 0 0 0> return code = 0x50000
usb 1-4: USB disconnect, address 6
usb 1-4: new high speed USB device using ehci_hcd and address 7
usb 1-4: device descriptor read/64, error -71
usb 1-4: 05-wait_for_sys timed out on ep0in
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
scsi3 : SCSI emulation for USB Mass Storage devices
usb 1-4: string descriptor 0 read error: -71
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi3, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-4: reset high speed USB device using ehci_hcd and address 7
usb 1-4: scsi_eh_3 timed out on ep0out
usb 1-4: failed to restore interface 0 altsetting 0 (error=-110)
scsi: Device offlined - not ready after error recovery: host 3 channel 0 id 0 lun 0
SCSI error : <3 0 0 0> return code = 0x50000
usb 1-4: USB disconnect, address 7
usb 1-4: new high speed USB device using ehci_hcd and address 8
usb 1-4: device descriptor read/64, error -71
usb 1-4: 05-wait_for_sys timed out on ep0in
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
usb 1-4: string descriptor 0 read error: -71
Vendor: HDS72808 Model: 0PLAT20 Rev: PF2O
Type: Direct-Access ANSI SCSI revision: 00
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
SCSI device sda: 160836480 512-byte hdwr sectors (82348 MB)
sda: assuming drive cache: write through
sda: sda1
Attached scsi disk sda at scsi4, channel 0, id 0, lun 0
usb-storage: device scan complete
usb 1-4: reset high speed USB device using ehci_hcd and address 8
usb 1-4: failed to restore interface 0 altsetting 0 (error=-71)
scsi: Device offlined - not ready after error recovery: host 4 channel 0 id 0 lun 0
SCSI error : <4 0 0 0> return code = 0x50000
usb 1-4: USB disconnect, address 8
and the kernel is:
Linux tuxor 2.6.10-rc3-ck1 #1 Sat Dec 4 15:26:16 EET 2004 i686 athlon i386 GNU/Linux
-- Eero
-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. http://productguide.itmanagersjournal.com/
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
