Guess it doesn't work with that device then. On Wed, 5 Jan 2005, Eero Heino wrote:
> > I added a line with the ids to kaweth.c and I got: > > usb 1-2: new full speed USB device using ohci_hcd and address 7 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC > PPS PES CCS > usb 1-2: ep0 maxpacket = 8 > usb 1-2: new device strings: Mfr=2, Product=3, SerialNumber=1 > usb 1-2: default language 0x0409 > usb 1-2: Product: USB 10M HomePNA Adapter > usb 1-2: Manufacturer: Generic > usb 1-2: SerialNumber: 00E0989BC8B3 > usb 1-2: hotplug > usb 1-2: adding 1-2:1.0 (config #1, interface 0) > usb 1-2:1.0: hotplug > kaweth 1-2:1.0: usb_probe_interface > kaweth 1-2:1.0: usb_probe_interface - got id > drivers/usb/net/kaweth.c: Downloading firmware... > drivers/usb/net/kaweth.c: Firmware loaded. I'll be back... > kaweth: probe of 1-2:1.0 failed with error -5 > hub 3-0:1.0: state 5 ports 5 chg ffe0 evt 0008 > ehci_hcd 0000:00:12.2: GetStatus port 3 status 001002 POWER sig=se0 CSC > hub 3-0:1.0: port 3, status 0100, change 0001, 12 Mb/s > hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x100 > hub 1-0:1.0: state 5 ports 3 chg fff8 evt 0004 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00030100 PESC > CSC PPS > hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s > usb 1-2: USB disconnect, address 7 > usb 1-2: usb_disable_device nuking all URBs > usb 1-2: unregistering interface 1-2:1.0 > usb 1-2:1.0: hotplug > usb 1-2: unregistering device > usb 1-2: hotplug > hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100 > hub 3-0:1.0: state 5 ports 5 chg ffe0 evt 0008 > ehci_hcd 0000:00:12.2: GetStatus port 3 status 001803 POWER sig=j CSC > CONNECT > hub 3-0:1.0: port 3, status 0501, change 0001, 480 Mb/s > hub 3-0:1.0: debounce: port 3: total 100ms stable 100ms status 0x501 > ehci_hcd 0000:00:12.2: port 3 full speed --> companion > ehci_hcd 0000:00:12.2: GetStatus port 3 status 003801 POWER OWNER sig=j > CONNECT > hub 1-0:1.0: state 5 ports 3 chg fff8 evt 0004 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010101 CSC > PPS CCS > hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s > hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x101 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC > PPS PES CCS > usb 1-2: new full speed USB device using ohci_hcd and address 8 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC > PPS PES CCS > usb 1-2: ep0 maxpacket = 8 > usb 1-2: device descriptor read/all, error -71 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC > PPS PES CCS > usb 1-2: new full speed USB device using ohci_hcd and address 9 > ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00100103 PRSC > PPS PES CCS > usb 1-2: ep0 maxpacket = 8 > usb 1-2: device descriptor read/all, error -71 > > any ideas? > > -- > Eero > > > On Wed, Jan 05, 2005 at 08:47:34AM -0800, Stephen J. Gowdy wrote: > > > It doesn't look like it gets recongied below, the says "driver=(none)". > > Looking at the working device list there is no listing for this device, > > but there is one close in number spaec (which might mean nothing); > > > > http://www.qbik.ch/usb/devices/showdev.php?id=638 > > > > It says you should use the kaweth driver for it. You could try editing the > > source and adding a line for your device (or just loading the driver might > > be enough, if it only uses that table for hotplug). > > > > > > -- > > /------------------------------------+-------------------------\ > > |Stephen J. Gowdy | SLAC, MailStop 34, | > > |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | > > |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | > > |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | > > \------------------------------------+-------------------------/ > > > -- /------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/ ------------------------------------------------------- The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt _______________________________________________ [email protected] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
