On Fri, Aug 19, 2005 at 04:02:26PM -0400, Alan Stern wrote:
>
> Did you ever make any progress on this? Did anything show up with
> CONFIG_USB_DEBUG turned on?
Here is the lsusb, lspci, dmesg, and debug log when the card is inserted
and then removed. A powered hub was connected but the card seemed
indifferent to that.
--
Ryan Underwood, <[EMAIL PROTECTED]>
Bus 003 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (#2)
iSerial 1 0000:05:00.1
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0x08
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 002 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 uhci_hcd
iProduct 2 VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller
iSerial 1 0000:05:00.0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 2
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
bPwrOn2PwrGood 1 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0x08
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Bus 001 Device 001: ID 0000:0000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 1 Single TT
bMaxPacketSize0 8
idVendor 0x0000
idProduct 0x0000
bcdDevice 2.06
iManufacturer 3 Linux 2.6.13 ehci_hcd
iProduct 2 VIA Technologies, Inc. USB 2.0
iSerial 1 0000:05:00.2
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 4
wHubCharacteristic 0x000a
No power switching (usb 1.0)
Per-port overcurrent protection
TT think time 8 FS bits
bPwrOn2PwrGood 10 * 2 milli seconds
bHubContrCurrent 0 milli Ampere
DeviceRemovable 0x08
PortPwrCtrlMask 0x08
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0100 power
Port 3: 0000.0100 power
Port 4: 0000.0100 power
0000:00:00.0 Host bridge: Toshiba America Info Systems 601 (rev 11)
00: 79 11 01 06 06 00 80 22 11 00 00 06 08 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 15 00 00 9d 02 00 00 19 18 c4 df 01 00 00 00
50: 18 00 00 00 00 00 00 00 03 00 00 fe 00 00 f0 fe
60: 00 00 00 00 00 00 00 00 f0 01 1a 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 31 00 fc 03 00 00 00 00 00 00 14 00 03 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 1a 00 00 00 44 00 00 00 00 00 00 00 ff ff 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
0000:00:02.0 CardBus bridge: Toshiba America Info Systems ToPIC95 (rev 07)
00: 79 11 0a 06 07 00 80 04 07 00 07 06 00 00 82 00
10: 00 00 14 09 00 00 80 04 00 01 04 00 00 00 00 0a
20: 00 f0 ff 0b 00 00 00 0c 00 f0 ff 0d 00 10 00 00
30: fc 10 00 00 00 14 00 00 fc 14 00 00 0b 01 80 05
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: d0 14 00 86 02 00 00 00 00 00 00 00 80 fd 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
0000:00:02.1 CardBus bridge: Toshiba America Info Systems ToPIC95 (rev 07)
00: 79 11 0a 06 07 00 80 04 07 00 07 06 00 00 82 00
10: 00 10 14 09 00 00 80 24 00 05 08 00 00 00 00 0e
20: 00 f0 ff 0f 00 00 00 10 00 f0 ff 11 00 18 00 00
30: fc 18 00 00 00 1c 00 00 fc 1c 00 00 0b 02 00 05
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 02 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: d0 24 00 86 02 00 00 00 00 00 00 00 80 fd 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
0000:00:04.0 VGA compatible controller: Chips and Technologies F65550 (rev 04)
00: 2c 10 e0 00 83 00 80 02 04 00 00 03 00 00 00 00
10: 00 00 00 fe 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:05:00.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61)
00: 06 11 38 30 07 00 10 02 61 00 03 0c 00 16 80 00
10: 00 00 00 00 00 08 00 10 00 00 00 00 00 00 00 00
20: 81 18 00 00 00 00 00 00 52 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 01 00 00
40: 40 10 03 00 00 00 00 00 00 0b 00 01 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00
0000:05:00.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61)
00: 06 11 38 30 07 00 10 02 61 00 03 0c 00 16 80 00
10: 00 00 00 00 00 09 00 10 00 00 00 00 00 00 00 00
20: a1 18 00 00 00 00 00 00 52 00 00 00 06 11 38 30
30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 01 00 00
40: 40 10 03 00 00 00 00 00 00 0b 00 01 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00
0000:05:00.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
00: 06 11 04 31 16 00 10 02 63 20 03 0c 08 16 80 00
10: 00 0a 00 10 00 0b 00 10 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 aa 00 00 00 06 11 04 31
30: 00 00 00 00 80 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 03 00 00 00 00 00 a0 20 00 09 00 00 ff ff
50: 00 5a 00 80 00 00 00 00 04 0b 88 88 33 00 00 00
60: 20 20 01 00 00 00 00 00 01 00 00 01 00 00 08 e0
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 01 00 c2 ff 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00
0000:05:00.3 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 46)
00: 06 11 44 30 87 00 10 02 46 10 00 0c 00 40 00 00
10: 00 00 00 10 01 18 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 44 30
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 00 20
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 01 00 02 e4 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Linux version 2.6.13 ([EMAIL PROTECTED]) (gcc version 4.0.1 (Debian 4.0.1-2))
#1 Sun Sep 4 14:53:02 CDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000009020000 (usable)
BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
144MB LOWMEM available.
On node 0 totalpages: 36896
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 32800 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI not present.
ACPI: Unable to locate RSDP
Allocating PCI resources starting at 09100000 (gap: 09020000:f6fc0000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro
No local APIC present or hardware disabled
mapped APIC to ffffd000 (01121000)
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 120.003 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 141636k/147584k available (1398k kernel code, 5340k reserved, 762k
data, 216k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 240.57 BogoMIPS (lpj=1202853)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 000001bf 00000000 00000000 00000000 00000000
00000000 00000000
CPU: After vendor identify, caps: 000001bf 00000000 00000000 00000000 00000000
00000000 00000000
Intel Pentium with F0 0F bug - workaround enabled.
CPU: After all inits, caps: 000001bf 00000000 00000000 00000000 00000000
00000000 00000000
mtrr: v2.0 (20020519)
CPU: Intel Pentium 75 - 200 stepping 0c
Checking 'hlt' instruction... OK.
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like
an initrd
Freeing initrd memory: 1368k freed
NET: Registered protocol family 16
EISA bus registered
PCI: PCI BIOS revision 2.10 entry at 0xfd50e, last bus=21
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f8dd0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x9aa6, dseg 0x0
PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:04.0
PCI: Bus 1, cardbus bridge: 0000:00:02.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 0a000000-0bffffff
MEM window: 0c000000-0dffffff
PCI: Bus 5, cardbus bridge: 0000:00:02.1
IO window: 00001800-000018ff
IO window: 00001c00-00001cff
PREFETCH window: 0e000000-0fffffff
MEM window: 10000000-11ffffff
PCI: Enabling device 0000:00:02.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:02.0 to 64
PCI: Enabling device 0000:00:02.1 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:02.1 to 64
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303,PNP0f13] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
EISA: Detected 0 cards.
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 1368KiB [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 216k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: FUJITSU MHH2048AT, ATA DISK drive
Probing IDE interface ide1...
hdc: TOSHIBA CD-ROM XM-1502BN, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 9514260 sectors (4871 MB) w/512KiB Cache, CHS=10068/15/63
hda: cache flushes not supported
hda: hda1 hda2
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 130446
ext3_orphan_cleanup: deleting unreferenced inode 130382
EXT3-fs: hda1: 2 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 460204k swap on /dev/hda2. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
hdc: ATAPI 10X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
Real Time Clock Driver v1.12
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.16ac)
Toshiba System Managment Mode driver v1.11 26/9/2001
register_blkdev: cannot get major 31 for mtdblock
Unable to register mtdblock block device on major 31: -16
slram: devname=ram_uncached, devstart=0x4000000, devlength=0x5000000
slram: ioremap failed
Yenta: CardBus bridge found at 0000:00:02.0 [0000:0000]
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000006
Yenta: CardBus bridge found at 0000:00:02.1 [0000:0000]
Yenta: ISA IRQ mask 0x0000, PCI irq 11
Socket status: 30000020
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
PCI: Enabling device 0000:05:00.2 (0000 -> 0002)
ehci_hcd 0000:05:00.2: VIA Technologies, Inc. USB 2.0
ehci_hcd 0000:05:00.2: reset hcs_params 0x2204 dbg=0 cc=2 pcc=2 ordered !ppc
ports=4
ehci_hcd 0000:05:00.2: reset hcc_params 6872 thresh 7 uframes 256/512/1024
ehci_hcd 0000:05:00.2: capability 0001 at 68
ehci_hcd 0000:05:00.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:05:00.2: irq 11, io mem 0x10000a00
ehci_hcd 0000:05:00.2: reset command 080002 (park)=0 ithresh=8 period=1024
Reset HALT
ehci_hcd 0000:05:00.2: init command 010009 (park)=0 ithresh=1 period=256 RUN
ehci_hcd 0000:05:00.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
ehci_hcd 0000:05:00.2: supports USB remote wakeup
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: VIA Technologies, Inc. USB 2.0
usb usb1: Manufacturer: Linux 2.6.13 ehci_hcd
usb usb1: SerialNumber: 0000:05:00.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0000
ieee1394: Initialized config rom entry `ip1394'
ohci1394: $Rev: 1299 $ Ben Collins <[EMAIL PROTECTED]>
PCI: Enabling device 0000:05:00.3 (0080 -> 0083)
PCI: Setting latency timer of device 0000:05:00.3 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[11] MMIO=[10000000-100007ff]
Max Packet=[1024]
USB Universal Host Controller Interface driver v2.3
PCI: Enabling device 0000:05:00.0 (0000 -> 0003)
uhci_hcd 0000:05:00.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:05:00.0: detected 2 ports
uhci_hcd 0000:05:00.0: check_and_reset_hc: legsup = 0x2000
uhci_hcd 0000:05:00.0: Performing full reset
uhci_hcd 0000:05:00.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:05:00.0: irq 11, io base 0x00001880
uhci_hcd 0000:05:00.0: supports USB remote wakeup
usb usb2: default language 0x0409
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
usb usb2: Manufacturer: Linux 2.6.13 uhci_hcd
usb usb2: SerialNumber: 0000:05:00.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: individual port over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:05:00.0: port 1 portsc 008a,00
hub 2-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
PCI: Enabling device 0000:05:00.1 (0000 -> 0003)
uhci_hcd 0000:05:00.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
(#2)
uhci_hcd 0000:05:00.1: detected 2 ports
uhci_hcd 0000:05:00.1: check_and_reset_hc: legsup = 0x2000
uhci_hcd 0000:05:00.1: Performing full reset
uhci_hcd 0000:05:00.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:05:00.1: irq 11, io base 0x000018a0
uhci_hcd 0000:05:00.1: supports USB remote wakeup
usb usb3: default language 0x0409
usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
usb usb3: Manufacturer: Linux 2.6.13 uhci_hcd
usb usb3: SerialNumber: 0000:05:00.1
usb usb3: hotplug
usb usb3: adding 3-0:1.0 (config #1, interface 0)
usb 3-0:1.0: hotplug
hub 3-0:1.0: usb_probe_interface
hub 3-0:1.0: usb_probe_interface - got id
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
hub 3-0:1.0: standalone hub
hub 3-0:1.0: no power switching (usb 1.0)
hub 3-0:1.0: individual port over-current protection
hub 3-0:1.0: power on to power good time: 2ms
hub 3-0:1.0: local power source is good
hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:05:00.0: port 2 portsc 008a,00
hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011060000003280]
hub 2-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
uhci_hcd 0000:05:00.1: port 1 portsc 008a,00
hub 3-0:1.0: port 1, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x100
uhci_hcd 0000:05:00.1: port 2 portsc 008a,00
hub 3-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
hub 3-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x100
hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
uhci_hcd 0000:05:00.0: suspend_rh (auto-stop)
uhci_hcd 0000:05:00.0: Controller not stopped yet!
uhci_hcd 0000:05:00.0: host controller process error, something bad happened!
uhci_hcd 0000:05:00.1: suspend_rh (auto-stop)
eth1394: $Rev: 1264 $ Ben Collins <[EMAIL PROTECTED]>
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
NET: Registered protocol family 17
input: PC Speaker
input: PS/2 Generic Mouse on isa0060/serio1
ts: Compaq touchscreen protocol output
mice: PS/2 mouse device common for all mice
Floppy drive(s): fd0 is 1.44M
FDC 0 is an 8272A
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
irda_init()
NET: Registered protocol family 23
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
NET: Registered protocol family 4
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
hdc: drive_cmd: status=0x51 { DriveReady SeekComplete Error }
hdc: drive_cmd: error=0x04 { AbortedCommand }
ide: failed opcode was: 0xec
cs: IO port probe 0x100-0x4ff: excluding 0x120-0x127 0x220-0x22f 0x388-0x38f
0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x100-0x4ff: excluding 0x120-0x127 0x220-0x22f 0x388-0x38f
0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xa00-0xaff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e7a40(lo)
IPv6 over IPv4 tunneling driver
Disabled Privacy Extensions on device c7c00c00(sit0)
openafs: no version for "struct_module" found: kernel tainted.
openafs: module license 'http://www.openafs.org/dl/license10.html' taints
kernel.
Found system call table at 0xc02989c0 (pattern scan)
Starting AFS cache scan...found 222 non-empty cache files (2%).
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
afs: Lost contact with volume location server 216.229.91.230 in cell
icequake.net
Sep 5 19:45:53 trysia kernel: On node 0 totalpages: 36896
Sep 5 19:45:53 trysia kernel: DMA zone: 4096 pages, LIFO batch:1
Sep 5 19:45:53 trysia kernel: Normal zone: 32800 pages, LIFO batch:15
Sep 5 19:45:53 trysia kernel: HighMem zone: 0 pages, LIFO batch:1
Sep 5 19:45:53 trysia kernel: mapped APIC to ffffd000 (01121000)
Sep 5 19:45:53 trysia kernel: CPU: After generic identify, caps: 000001bf
00000000 00000000 00000000 00000000 00000000 00000000
Sep 5 19:45:53 trysia kernel: CPU: After vendor identify, caps: 000001bf
00000000 00000000 00000000 00000000 00000000 00000000
Sep 5 19:45:53 trysia kernel: CPU: After all inits, caps: 000001bf 00000000
00000000 00000000 00000000 00000000 00000000
Sep 5 19:45:53 trysia kernel: Boot video device is 0000:00:04.0
Sep 5 19:45:53 trysia kernel: PCI: Setting latency timer of device
0000:00:02.0 to 64
Sep 5 19:45:53 trysia kernel: PCI: Setting latency timer of device
0000:00:02.1 to 64
Sep 5 19:45:53 trysia kernel: Probing IDE interface ide0...
Sep 5 19:45:53 trysia kernel: Probing IDE interface ide1...
Sep 5 19:45:53 trysia kernel: ext3_orphan_cleanup: deleting unreferenced inode
130446
Sep 5 19:45:53 trysia kernel: ext3_orphan_cleanup: deleting unreferenced inode
130382
Sep 5 19:45:54 trysia kernel: slram: devname=ram_uncached, devstart=0x4000000,
devlength=0x5000000
Sep 5 19:45:54 trysia kernel: ehci_hcd: block sizes: qh 128 qtd 96 itd 192
sitd 96
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: reset hcs_params 0x2204
dbg=0 cc=2 pcc=2 ordered !ppc ports=4
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: reset hcc_params 6872
thresh 7 uframes 256/512/1024
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: capability 0001 at 68
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: reset command 080002
(park)=0 ithresh=8 period=1024 Reset HALT
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: init command 010009
(park)=0 ithresh=1 period=256 RUN
Sep 5 19:45:54 trysia kernel: ehci_hcd 0000:05:00.2: supports USB remote wakeup
Sep 5 19:45:54 trysia kernel: usb usb1: default language 0x0409
Sep 5 19:45:54 trysia kernel: usb usb1: new device strings: Mfr=3, Product=2,
SerialNumber=1
Sep 5 19:45:54 trysia kernel: usb usb1: hotplug
Sep 5 19:45:54 trysia kernel: usb usb1: adding 1-0:1.0 (config #1, interface 0)
Sep 5 19:45:54 trysia kernel: usb 1-0:1.0: hotplug
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: usb_probe_interface
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: usb_probe_interface - got id
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: standalone hub
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: no power switching (usb 1.0)
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: individual port over-current
protection
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: Single TT
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: TT requires at most 8 FS bit times
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: power on to power good time: 20ms
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: local power source is good
Sep 5 19:45:54 trysia kernel: hub 1-0:1.0: state 5 ports 4 chg 0000 evt 0000
Sep 5 19:45:54 trysia kernel: ieee1394: Initialized config rom entry `ip1394'
Sep 5 19:45:54 trysia kernel: PCI: Setting latency timer of device
0000:05:00.3 to 64
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: check_and_reset_hc:
legsup = 0x2000
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: Performing full reset
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: supports USB remote wakeup
Sep 5 19:45:54 trysia kernel: usb usb2: default language 0x0409
Sep 5 19:45:54 trysia kernel: usb usb2: new device strings: Mfr=3, Product=2,
SerialNumber=1
Sep 5 19:45:54 trysia kernel: usb usb2: hotplug
Sep 5 19:45:54 trysia kernel: usb usb2: adding 2-0:1.0 (config #1, interface 0)
Sep 5 19:45:54 trysia kernel: usb 2-0:1.0: hotplug
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: usb_probe_interface
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: usb_probe_interface - got id
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: standalone hub
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: no power switching (usb 1.0)
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: individual port over-current
protection
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: power on to power good time: 2ms
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: local power source is good
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: port 1 portsc 008a,00
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: port 1, status 0100, change 0003,
12 Mb/s
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: check_and_reset_hc:
legsup = 0x2000
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: Performing full reset
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: supports USB remote wakeup
Sep 5 19:45:54 trysia kernel: usb usb3: default language 0x0409
Sep 5 19:45:54 trysia kernel: usb usb3: new device strings: Mfr=3, Product=2,
SerialNumber=1
Sep 5 19:45:54 trysia kernel: usb usb3: hotplug
Sep 5 19:45:54 trysia kernel: usb usb3: adding 3-0:1.0 (config #1, interface 0)
Sep 5 19:45:54 trysia kernel: usb 3-0:1.0: hotplug
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: usb_probe_interface
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: usb_probe_interface - got id
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: standalone hub
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: no power switching (usb 1.0)
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: individual port over-current
protection
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: power on to power good time: 2ms
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: local power source is good
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x100
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: port 2 portsc 008a,00
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: port 2, status 0100, change 0003,
12 Mb/s
Sep 5 19:45:54 trysia kernel: ieee1394: Host added: ID:BUS[0-00:1023]
GUID[0011060000003280]
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: debounce: port 2: total 100ms
stable 100ms status 0x100
Sep 5 19:45:54 trysia kernel: hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0000
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: port 1 portsc 008a,00
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: port 1, status 0100, change 0003,
12 Mb/s
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: debounce: port 1: total 100ms
stable 100ms status 0x100
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: port 2 portsc 008a,00
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: port 2, status 0100, change 0003,
12 Mb/s
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: debounce: port 2: total 100ms
stable 100ms status 0x100
Sep 5 19:45:54 trysia kernel: hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0000
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.0: suspend_rh (auto-stop)
Sep 5 19:45:54 trysia kernel: uhci_hcd 0000:05:00.1: suspend_rh (auto-stop)
Sep 5 19:45:54 trysia kernel: irda_init()
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: device removed
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: reset command ffffffff
park=3 ithresh=63 LReset IAAD Async Periodic period=?? R
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.0: wakeup_rh (auto-start)
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.1: wakeup_rh (auto-start)
Sep 5 19:50:20 trysia kernel: hub 1-0:1.0: state 0 ports 4 chg 0000 evt 0000
Sep 5 19:50:20 trysia kernel: hub 2-0:1.0: state 5 ports 2 chg 0000 evt 0006
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.0: port 1 portsc fbff,04
Sep 5 19:50:20 trysia kernel: hub 2-0:1.0: port 1, status 0317, change 000b,
1.5 Mb/s
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.0: port 1 portsc fbff,04
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.0: roothub graceful
disconnect
Sep 5 19:50:20 trysia kernel: hub 3-0:1.0: state 5 ports 2 chg 0000 evt 0006
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.1: port 1 portsc fbff,04
Sep 5 19:50:20 trysia kernel: usb usb2: usb_disable_device nuking all URBs
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.0: shutdown urb c7657560
pipe 40408180 ep1in-intr
Sep 5 19:50:20 trysia kernel: usb usb2: unregistering interface 2-0:1.0
Sep 5 19:50:20 trysia kernel: usb 2-0:1.0: hotplug
Sep 5 19:50:20 trysia kernel: usb usb2: unregistering device
Sep 5 19:50:20 trysia kernel: usb usb2: hotplug
Sep 5 19:50:20 trysia kernel: hub 3-0:1.0: port 1, status 0317, change 000b,
1.5 Mb/s
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.1: port 1 portsc fbff,04
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.1: roothub graceful
disconnect
Sep 5 19:50:20 trysia kernel: usb usb3: usb_disable_device nuking all URBs
Sep 5 19:50:20 trysia kernel: uhci_hcd 0000:05:00.1: shutdown urb c76570e0
pipe 40408180 ep1in-intr
Sep 5 19:50:20 trysia kernel: usb usb3: unregistering interface 3-0:1.0
Sep 5 19:50:20 trysia kernel: usb 3-0:1.0: hotplug
Sep 5 19:50:20 trysia kernel: usb usb3: unregistering device
Sep 5 19:50:20 trysia kernel: usb usb3: hotplug
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: roothub graceful
disconnect
Sep 5 19:50:20 trysia kernel: usb usb1: usb_disable_device nuking all URBs
Sep 5 19:50:20 trysia kernel: usb usb1: unregistering interface 1-0:1.0
Sep 5 19:50:20 trysia kernel: usb 1-0:1.0: hotplug
Sep 5 19:50:20 trysia kernel: usb usb1: unregistering device
Sep 5 19:50:20 trysia kernel: usb usb1: hotplug
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: stop
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: reset command ffffffff
park=3 ithresh=63 LReset IAAD Async Periodic period=?? R
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: irq normal 0 err 0
reclaim 0 (lost 0)
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: complete 0 unlink 0
Sep 5 19:50:20 trysia kernel: ehci_hcd 0000:05:00.2: ehci_stop completed
status ffffffff Async Periodic Recl Halt IAA FATAL FLR PCD
Sep 5 19:50:20 trysia kernel: ieee1394: Node removed: ID:BUS[0-00:1023]
GUID[0011060000003280]
Sep 5 19:51:26 trysia kernel: usbcore: khubd exiting
Sep 5 19:52:14 trysia kernel: eth0: no IPv6 routers present
Sep 5 19:52:44 trysia kernel: ehci_hcd: block sizes: qh 128 qtd 96 itd 192
sitd 96
Sep 5 19:52:44 trysia kernel: ohci_hcd: 2005 April 22 USB 1.1 'Open' Host
Controller (OHCI) Driver (PCI)
Sep 5 19:52:44 trysia kernel: ohci_hcd: block sizes: ed 64 td 64
