Hello, I'm trying to use the at91_udc and the g_serial (ACM or not ACM mode) from the kernel 2.6.21. I use them on a custom board (at91sam9260), and I think (or hope) I have no hardware's problems because I start the board through USB device and SAMBA. But when I plug the usb device(my custom board) to a winxp I've this message. Can someone help me?
thanks udc: at91_udc version 3 May 2006 gs_bind: Gadget Serial v2.2 bound udc: active udc: bound to g_serial gs_module_init: Gadget Serial v2.2 loaded # udc: end bus reset udc: SETUP 80.06 v0100 i0000 l0040 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: end bus reset udc: nuke ep0 gs_setup_complete: status error, status=-108, actual=16, length=18 gs_disconnect: Gadget Serial disconnected udc: SETUP 00.05 v0002 i0000 l0000 udc: address 2 udc: SETUP 80.06 v0100 i0000 l0012 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/2 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0200 i0000 l0009 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/1 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0300 i0000 l00ff udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0303 i0409 l00ff udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0200 i0000 l00ff udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/3 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0600 i0000 l000a udc: req 80.06 protocol STALL; stat -95 udc: ep0 stalled udc: SETUP 80.06 v0300 i0000 l00ff udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0302 i0409 l00ff udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0300 i0000 l00ff udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0302 i0409 l00ff udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/4 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0100 i0000 l0012 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/2 (done) udc: ep0 out/status ACK udc: SETUP 80.06 v0200 i0000 l0109 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/8 udc: ep0 c0020ca0 in/3 (done) udc: ep0 out/status ACK udc: SETUP 00.09 v0002 i0000 l0000 udc: wait for config gs_set_config: Gadget Serial configured, full speed CDC-ACM config udc: toggle config udc: ep0 in/status udc: SETUP a1.21 v0000 i0000 l0007 udc: ep0 c0020ca0 in/7 (done) udc: ep0 out/status ACK udc: SETUP 21.22 v0000 i0000 l0000 udc: ep0 in/status ------------------------------------------------------------------------- Les informations précédentes peuvent être confidentielles ou privilégiées. Si vous n'êtes pas le destinataire prévu de ce mail, veuillez en notifier l'expéditeur en répondant à ce message puis supprimez-en toute trace de vos systèmes. TIL Technologies 1330, rue de la Lauzière 13856 AIX EN PROVENCE Tel. : +33 4 42 37 11 77 ------------------------------------------------------------------------- ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Linux-usb-users@lists.sourceforge.net To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
