> > [ 1342.644000] ehci_hcd 0000:00:0b.1: GetStatus port 2 > status 001005 > > POWER sig=se0 PE CONNECT [ 1342.700000] usb 2-2: new high speed USB > > device using ehci_hcd and address 3 [ 1342.700000] ehci_hcd > > 0000:00:0b.1: devpath 2 ep0in 3strikes [ 1342.700000] ehci_hcd > > 0000:00:0b.1: devpath 2 ep0in 3strikes [ 1342.700000] ehci_hcd > > 0000:00:0b.1: devpath 2 ep0in 3strikes > > These are low-level hardware errors. They indicate that the > EHCI controller on your computer isn't able to communicate > with the device. > Either a bad connection is mangling the signal somehow, or > else the USB hardware on the computer or on the device isn't > working quite right. > > Do you have any other high-speed devices to test the EHCI > controller with? Do you have other computers to try plugging > the device into?
Hi Alan, I've put in a couple of other devices, namely a 4-slot USB reader and a USB stick. The USB stick seems to have a filesystem problem and is being mounted as read-only, recall in my 'other' post where I mentioned not being to write. I'll fix this straight after I click 'send'. Anyhow, both seem to be properly registered though. I've included some debug messages below,... Firstly when inserting the USB stick: [=========] [ 136.508000] hub 2-0:1.0: state 8 ports 8 chg 0000 evt 0000 [ 136.508000] usb usb2: usb auto-resume [ 136.508000] usb usb2: finish resume [ 136.508000] hub 2-0:1.0: hub_resume [ 136.508000] ehci_hcd 0000:00:0b.1: resume root hub [ 136.528000] ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001803 POWER sig=j CSC CONNECT [ 136.528000] hub 2-0:1.0: port 1, status 0501, change 0001, 480 Mb/s [ 136.656000] hub 2-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501 [ 136.712000] ehci_hcd 0000:00:0b.1: port 1 high speed [ 136.712000] ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 136.768000] usb 2-1: new high speed USB device using ehci_hcd and address 3 [ 136.860000] ehci_hcd 0000:00:0b.1: port 1 high speed [ 136.860000] ehci_hcd 0000:00:0b.1: GetStatus port 1 status 001005 POWER sig=se0 PE CONNECT [ 136.972000] usb 2-1: default language 0x0409 [ 136.972000] usb 2-1: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 136.972000] usb 2-1: Product: Mass Storage [ 136.972000] usb 2-1: Manufacturer: Generic [ 136.972000] usb 2-1: SerialNumber: 49816AA5 [ 136.972000] PM: Adding info for usb:2-1 [ 136.972000] usb 2-1: uevent [ 136.972000] usb 2-1: usb_probe_device [ 136.972000] PM: Adding info for No Bus:usbdev2.3_ep00 [ 136.972000] usb 2-1: configuration #1 chosen from 1 choice [ 136.972000] usb 2-1: adding 2-1:1.0 (config #1, interface 0) [ 136.972000] PM: Adding info for usb:2-1:1.0 [ 136.972000] usb 2-1:1.0: uevent [ 136.972000] PM: Adding info for No Bus:usbdev2.3_ep01 [ 136.972000] PM: Adding info for No Bus:usbdev2.3_ep82 [ 136.976000] PM: Adding info for No Bus:usbdev2.3 [ 136.976000] drivers/usb/core/inode.c: creating file '003' [ 136.976000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0000 [ 137.060000] libusual 2-1:1.0: usb_probe_interface [ 137.060000] libusual 2-1:1.0: usb_probe_interface - got id [ 137.060000] usbcore: registered new interface driver libusual [ 137.112000] Initializing USB Mass Storage driver... [ 137.112000] usb-storage 2-1:1.0: usb_probe_interface [ 137.112000] usb-storage 2-1:1.0: usb_probe_interface - got id [ 137.112000] scsi4 : SCSI emulation for USB Mass Storage devices [ 137.112000] PM: Adding info for No Bus:host4 [ 137.112000] usbcore: registered new interface driver usb-storage [ 137.112000] USB Mass Storage support registered. [ 137.116000] usb-storage: device found at 3 [ 137.116000] usb-storage: waiting for device to settle before scanning [ 142.116000] usb-storage: device scan complete [ 142.116000] PM: Adding info for No Bus:target4:0:0 [ 142.156000] scsi 4:0:0:0: Direct-Access Alcor Flash Disk 8.00 PQ: 0 ANSI: 2 [ 142.156000] PM: Adding info for No Bus:target4:0:1 [ 142.160000] PM: Removing info for No Bus:target4:0:1 [ 142.160000] PM: Adding info for No Bus:target4:0:2 [ 142.160000] PM: Removing info for No Bus:target4:0:2 [ 142.160000] PM: Adding info for No Bus:target4:0:3 [ 142.160000] PM: Removing info for No Bus:target4:0:3 [ 142.160000] PM: Adding info for No Bus:target4:0:4 [ 142.160000] PM: Removing info for No Bus:target4:0:4 [ 142.160000] PM: Adding info for No Bus:target4:0:5 [ 142.160000] PM: Removing info for No Bus:target4:0:5 [ 142.160000] PM: Adding info for No Bus:target4:0:6 [ 142.160000] PM: Removing info for No Bus:target4:0:6 [ 142.160000] PM: Adding info for No Bus:target4:0:7 [ 142.160000] PM: Removing info for No Bus:target4:0:7 [ 142.160000] PM: Adding info for scsi:4:0:0:0 [ 142.164000] SCSI device sdb: 8192000 512-byte hdwr sectors (4194 MB) [ 142.168000] sdb: Write Protect is off [ 142.168000] sdb: Mode Sense: 03 00 00 00 [ 142.168000] sdb: assuming drive cache: write through [ 142.172000] SCSI device sdb: 8192000 512-byte hdwr sectors (4194 MB) [ 142.172000] sdb: Write Protect is off [ 142.172000] sdb: Mode Sense: 03 00 00 00 [ 142.172000] sdb: assuming drive cache: write through [ 142.172000] sdb: unknown partition table [ 142.176000] sd 4:0:0:0: Attached scsi removable disk sdb [ 142.176000] sd 4:0:0:0: Attached scsi generic sg1 type 0 [ 143.800000] FAT: Filesystem panic (dev sdb) [ 143.800000] fat_get_cluster: invalid cluster chain (i_pos 0) [ 143.800000] File system has been set read-only [=========] Then the 4-slot USB reader: [=========] [ 422.380000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 422.380000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT [ 422.380000] hub 2-0:1.0: port 4, status 0501, change 0001, 480 Mb/s [ 422.508000] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 [ 422.564000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 422.564000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 422.620000] usb 2-4: new high speed USB device using ehci_hcd and address 4 [ 422.676000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 422.676000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 422.752000] usb 2-4: default language 0x0409 [ 422.756000] usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 422.756000] usb 2-4: Product: Winter Ver1.3 [ 422.756000] usb 2-4: Manufacturer: Ltd [ 422.756000] usb 2-4: SerialNumber: 996996813041 [ 422.756000] PM: Adding info for usb:2-4 [ 422.756000] usb 2-4: uevent [ 422.756000] usb 2-4: usb_probe_device [ 422.756000] PM: Adding info for No Bus:usbdev2.4_ep00 [ 422.756000] usb 2-4: configuration #1 chosen from 1 choice [ 422.756000] usb 2-4: adding 2-4:1.0 (config #1, interface 0) [ 422.756000] PM: Adding info for usb:2-4:1.0 [ 422.756000] usb 2-4:1.0: uevent [ 422.756000] libusual 2-4:1.0: usb_probe_interface [ 422.756000] libusual 2-4:1.0: usb_probe_interface - got id [ 422.756000] usb-storage 2-4:1.0: usb_probe_interface [ 422.756000] usb-storage 2-4:1.0: usb_probe_interface - got id [ 422.756000] scsi5 : SCSI emulation for USB Mass Storage devices [ 422.756000] PM: Adding info for No Bus:host5 [ 422.756000] usb-storage: device found at 4 [ 422.756000] usb-storage: waiting for device to settle before scanning [ 422.756000] PM: Adding info for No Bus:usbdev2.4_ep81 [ 422.756000] PM: Adding info for No Bus:usbdev2.4_ep02 [ 422.756000] PM: Adding info for No Bus:usbdev2.4 [ 422.756000] drivers/usb/core/inode.c: creating file '004' [ 427.756000] usb-storage: device scan complete [ 427.756000] PM: Adding info for No Bus:target5:0:0 [ 427.756000] scsi 5:0:0:0: Direct-Access USB2.0 CardReader CF RW 0.0> PQ: 0 ANSI: 0 [ 427.756000] scsi 5:0:0:1: Direct-Access USB2.0 CardReader SD RW 0.0> PQ: 0 ANSI: 0 [ 427.760000] scsi 5:0:0:2: Direct-Access USB2.0 CardReader SM RW 0.0> PQ: 0 ANSI: 0 [ 427.760000] scsi 5:0:0:3: Direct-Access USB2.0 CardReader MS RW 0.0> PQ: 0 ANSI: 0 [ 427.760000] PM: Adding info for No Bus:target5:0:1 [ 427.760000] PM: Removing info for No Bus:target5:0:1 [ 427.760000] PM: Adding info for No Bus:target5:0:2 [ 427.760000] PM: Removing info for No Bus:target5:0:2 [ 427.760000] PM: Adding info for No Bus:target5:0:3 [ 427.760000] PM: Removing info for No Bus:target5:0:3 [ 427.760000] PM: Adding info for No Bus:target5:0:4 [ 427.760000] PM: Removing info for No Bus:target5:0:4 [ 427.760000] PM: Adding info for No Bus:target5:0:5 [ 427.760000] PM: Removing info for No Bus:target5:0:5 [ 427.760000] PM: Adding info for No Bus:target5:0:6 [ 427.764000] PM: Removing info for No Bus:target5:0:6 [ 427.764000] PM: Adding info for No Bus:target5:0:7 [ 427.764000] PM: Removing info for No Bus:target5:0:7 [ 427.764000] PM: Adding info for scsi:5:0:0:0 [ 427.764000] sd 5:0:0:0: Attached scsi removable disk sdc [ 427.764000] sd 5:0:0:0: Attached scsi generic sg2 type 0 [ 427.764000] PM: Adding info for scsi:5:0:0:1 [ 427.768000] sd 5:0:0:1: Attached scsi removable disk sdd [ 427.768000] sd 5:0:0:1: Attached scsi generic sg3 type 0 [ 427.768000] PM: Adding info for scsi:5:0:0:2 [ 427.772000] sd 5:0:0:2: Attached scsi removable disk sde [ 427.772000] sd 5:0:0:2: Attached scsi generic sg4 type 0 [ 427.772000] PM: Adding info for scsi:5:0:0:3 [ 427.772000] sd 5:0:0:3: Attached scsi removable disk sdf [ 427.772000] sd 5:0:0:3: Attached scsi generic sg5 type 0 [ 428.812000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 428.812000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001002 POWER sig=se0 CSC [ 428.812000] hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s [ 428.812000] usb 2-4: USB disconnect, address 4 [ 428.812000] usb 2-4: unregistering device [ 428.812000] usb 2-4: usb_disable_device nuking all URBs [ 428.812000] usb 2-4: unregistering interface 2-4:1.0 [ 428.812000] PM: Removing info for No Bus:usbdev2.4_ep81 [ 428.812000] usbdev2.4_ep81: ep_device_release called for usbdev2.4_ep81 [ 428.812000] PM: Removing info for No Bus:usbdev2.4_ep02 [ 428.812000] usbdev2.4_ep02: ep_device_release called for usbdev2.4_ep02 [ 428.816000] PM: Removing info for scsi:5:0:0:0 [ 428.816000] PM: Removing info for scsi:5:0:0:1 [ 428.816000] PM: Removing info for scsi:5:0:0:2 [ 428.816000] PM: Removing info for scsi:5:0:0:3 [ 428.816000] PM: Removing info for No Bus:target5:0:0 [ 428.816000] PM: Removing info for No Bus:host5 [ 428.816000] PM: Removing info for usb:2-4:1.0 [ 428.816000] usb 2-4:1.0: uevent [ 428.816000] PM: Removing info for No Bus:usbdev2.4 [ 428.816000] PM: Removing info for No Bus:usbdev2.4_ep00 [ 428.816000] usbdev2.4_ep00: ep_device_release called for usbdev2.4_ep00 [ 428.816000] PM: Removing info for usb:2-4 [ 428.816000] usb 2-4: uevent [ 428.848000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001002 POWER sig=se0 CSC [ 428.976000] hub 2-0:1.0: debounce: port 4: total 125ms stable 100ms status 0x100 [ 428.976000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 432.408000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 432.408000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT [ 432.408000] hub 2-0:1.0: port 4, status 0501, change 0001, 480 Mb/s [ 432.536000] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 [ 432.592000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 432.592000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 432.648000] usb 2-4: new high speed USB device using ehci_hcd and address 5 [ 432.704000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 432.704000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 432.780000] usb 2-4: default language 0x0409 [ 432.784000] usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 432.784000] usb 2-4: Product: Winter Ver1.3 [ 432.784000] usb 2-4: Manufacturer: Ltd [ 432.784000] usb 2-4: SerialNumber: 996996813041 [ 432.784000] PM: Adding info for usb:2-4 [ 432.784000] usb 2-4: uevent [ 432.784000] usb 2-4: usb_probe_device [ 432.784000] PM: Adding info for No Bus:usbdev2.5_ep00 [ 432.784000] usb 2-4: configuration #1 chosen from 1 choice [ 432.784000] usb 2-4: adding 2-4:1.0 (config #1, interface 0) [ 432.784000] PM: Adding info for usb:2-4:1.0 [ 432.784000] usb 2-4:1.0: uevent [ 432.784000] libusual 2-4:1.0: usb_probe_interface [ 432.784000] libusual 2-4:1.0: usb_probe_interface - got id [ 432.784000] usb-storage 2-4:1.0: usb_probe_interface [ 432.784000] usb-storage 2-4:1.0: usb_probe_interface - got id [ 432.784000] scsi6 : SCSI emulation for USB Mass Storage devices [ 432.784000] PM: Adding info for No Bus:host6 [ 432.784000] usb-storage: device found at 5 [ 432.784000] usb-storage: waiting for device to settle before scanning [ 432.784000] PM: Adding info for No Bus:usbdev2.5_ep81 [ 432.784000] PM: Adding info for No Bus:usbdev2.5_ep02 [ 432.784000] PM: Adding info for No Bus:usbdev2.5 [ 432.784000] drivers/usb/core/inode.c: creating file '005' [ 436.460000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 436.460000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001002 POWER sig=se0 CSC [ 436.464000] hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s [ 436.464000] usb 2-4: USB disconnect, address 5 [ 436.464000] usb 2-4: unregistering device [ 436.464000] usb 2-4: usb_disable_device nuking all URBs [ 436.464000] usb 2-4: unregistering interface 2-4:1.0 [ 436.464000] PM: Removing info for No Bus:usbdev2.5_ep81 [ 436.464000] usbdev2.5_ep81: ep_device_release called for usbdev2.5_ep81 [ 436.464000] PM: Removing info for No Bus:usbdev2.5_ep02 [ 436.464000] usbdev2.5_ep02: ep_device_release called for usbdev2.5_ep02 [ 436.464000] PM: Removing info for No Bus:host6 [ 436.464000] PM: Removing info for usb:2-4:1.0 [ 436.464000] usb 2-4:1.0: uevent [ 436.464000] PM: Removing info for No Bus:usbdev2.5 [ 436.464000] PM: Removing info for No Bus:usbdev2.5_ep00 [ 436.464000] usbdev2.5_ep00: ep_device_release called for usbdev2.5_ep00 [ 436.464000] PM: Removing info for usb:2-4 [ 436.464000] usb 2-4: uevent [ 436.496000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001002 POWER sig=se0 CSC [ 436.624000] hub 2-0:1.0: debounce: port 4: total 125ms stable 100ms status 0x100 [ 436.624000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 439.488000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 439.488000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT [ 439.488000] hub 2-0:1.0: port 4, status 0501, change 0001, 480 Mb/s [ 439.616000] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 [ 439.672000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 439.672000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 439.728000] usb 2-4: new high speed USB device using ehci_hcd and address 6 [ 439.784000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 439.784000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 439.860000] usb 2-4: default language 0x0409 [ 439.864000] usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 439.864000] usb 2-4: Product: Winter Ver1.3 [ 439.864000] usb 2-4: Manufacturer: Ltd [ 439.864000] usb 2-4: SerialNumber: 996996813041 [ 439.864000] PM: Adding info for usb:2-4 [ 439.864000] usb 2-4: uevent [ 439.864000] usb 2-4: usb_probe_device [ 439.864000] PM: Adding info for No Bus:usbdev2.6_ep00 [ 439.864000] usb 2-4: configuration #1 chosen from 1 choice [ 439.864000] usb 2-4: adding 2-4:1.0 (config #1, interface 0) [ 439.864000] PM: Adding info for usb:2-4:1.0 [ 439.864000] usb 2-4:1.0: uevent [ 439.864000] libusual 2-4:1.0: usb_probe_interface [ 439.864000] libusual 2-4:1.0: usb_probe_interface - got id [ 439.864000] usb-storage 2-4:1.0: usb_probe_interface [ 439.864000] usb-storage 2-4:1.0: usb_probe_interface - got id [ 439.864000] scsi7 : SCSI emulation for USB Mass Storage devices [ 439.864000] PM: Adding info for No Bus:host7 [ 439.864000] usb-storage: device found at 6 [ 439.864000] usb-storage: waiting for device to settle before scanning [ 439.864000] PM: Adding info for No Bus:usbdev2.6_ep81 [ 439.864000] PM: Adding info for No Bus:usbdev2.6_ep02 [ 439.864000] PM: Adding info for No Bus:usbdev2.6 [ 439.864000] drivers/usb/core/inode.c: creating file '006' [ 440.356000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 440.356000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001002 POWER sig=se0 CSC [ 440.356000] hub 2-0:1.0: port 4, status 0100, change 0001, 12 Mb/s [ 440.356000] usb 2-4: USB disconnect, address 6 [ 440.356000] usb 2-4: unregistering device [ 440.356000] usb 2-4: usb_disable_device nuking all URBs [ 440.356000] usb 2-4: unregistering interface 2-4:1.0 [ 440.356000] PM: Removing info for No Bus:usbdev2.6_ep81 [ 440.356000] usbdev2.6_ep81: ep_device_release called for usbdev2.6_ep81 [ 440.356000] PM: Removing info for No Bus:usbdev2.6_ep02 [ 440.356000] usbdev2.6_ep02: ep_device_release called for usbdev2.6_ep02 [ 440.356000] PM: Removing info for No Bus:host7 [ 440.356000] PM: Removing info for usb:2-4:1.0 [ 440.356000] usb 2-4:1.0: uevent [ 440.356000] PM: Removing info for No Bus:usbdev2.6 [ 440.356000] PM: Removing info for No Bus:usbdev2.6_ep00 [ 440.356000] usbdev2.6_ep00: ep_device_release called for usbdev2.6_ep00 [ 440.356000] PM: Removing info for usb:2-4 [ 440.356000] usb 2-4: uevent [ 440.484000] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x100 [ 443.364000] hub 2-0:1.0: state 7 ports 8 chg 0000 evt 0010 [ 443.364000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001803 POWER sig=j CSC CONNECT [ 443.364000] hub 2-0:1.0: port 4, status 0501, change 0001, 480 Mb/s [ 443.492000] hub 2-0:1.0: debounce: port 4: total 100ms stable 100ms status 0x501 [ 443.548000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 443.548000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 443.604000] usb 2-4: new high speed USB device using ehci_hcd and address 7 [ 443.660000] ehci_hcd 0000:00:0b.1: port 4 high speed [ 443.660000] ehci_hcd 0000:00:0b.1: GetStatus port 4 status 001005 POWER sig=se0 PE CONNECT [ 443.736000] usb 2-4: default language 0x0409 [ 443.740000] usb 2-4: new device strings: Mfr=1, Product=2, SerialNumber=3 [ 443.740000] usb 2-4: Product: Winter Ver1.3 [ 443.740000] usb 2-4: Manufacturer: Ltd [ 443.740000] usb 2-4: SerialNumber: 996996813041 [ 443.740000] PM: Adding info for usb:2-4 [ 443.740000] usb 2-4: uevent [ 443.740000] usb 2-4: usb_probe_device [ 443.740000] PM: Adding info for No Bus:usbdev2.7_ep00 [ 443.740000] usb 2-4: configuration #1 chosen from 1 choice [ 443.740000] usb 2-4: adding 2-4:1.0 (config #1, interface 0) [ 443.740000] PM: Adding info for usb:2-4:1.0 [ 443.740000] usb 2-4:1.0: uevent [ 443.740000] libusual 2-4:1.0: usb_probe_interface [ 443.740000] libusual 2-4:1.0: usb_probe_interface - got id [ 443.740000] usb-storage 2-4:1.0: usb_probe_interface [ 443.740000] usb-storage 2-4:1.0: usb_probe_interface - got id [ 443.740000] scsi8 : SCSI emulation for USB Mass Storage devices [ 443.740000] PM: Adding info for No Bus:host8 [ 443.740000] usb-storage: device found at 7 [ 443.740000] usb-storage: waiting for device to settle before scanning [ 443.740000] PM: Adding info for No Bus:usbdev2.7_ep81 [ 443.740000] PM: Adding info for No Bus:usbdev2.7_ep02 [ 443.740000] PM: Adding info for No Bus:usbdev2.7 [ 443.740000] drivers/usb/core/inode.c: creating file '007' [ 448.740000] usb-storage: device scan complete [ 448.740000] PM: Adding info for No Bus:target8:0:0 [ 448.740000] scsi 8:0:0:0: Direct-Access USB2.0 CardReader CF RW 0.0> PQ: 0 ANSI: 0 [ 448.904000] scsi 8:0:0:1: Direct-Access USB2.0 CardReader SD RW 0.0> PQ: 0 ANSI: 0 [ 448.904000] scsi 8:0:0:2: Direct-Access USB2.0 CardReader SM RW 0.0> PQ: 0 ANSI: 0 [ 448.904000] scsi 8:0:0:3: Direct-Access USB2.0 CardReader MS RW 0.0> PQ: 0 ANSI: 0 [ 448.904000] PM: Adding info for No Bus:target8:0:1 [ 448.904000] PM: Removing info for No Bus:target8:0:1 [ 448.904000] PM: Adding info for No Bus:target8:0:2 [ 448.904000] PM: Removing info for No Bus:target8:0:2 [ 448.904000] PM: Adding info for No Bus:target8:0:3 [ 448.904000] PM: Removing info for No Bus:target8:0:3 [ 448.904000] PM: Adding info for No Bus:target8:0:4 [ 448.904000] PM: Removing info for No Bus:target8:0:4 [ 448.904000] PM: Adding info for No Bus:target8:0:5 [ 448.904000] PM: Removing info for No Bus:target8:0:5 [ 448.904000] PM: Adding info for No Bus:target8:0:6 [ 448.904000] PM: Removing info for No Bus:target8:0:6 [ 448.904000] PM: Adding info for No Bus:target8:0:7 [ 448.904000] PM: Removing info for No Bus:target8:0:7 [ 448.904000] PM: Adding info for scsi:8:0:0:0 [ 448.908000] sd 8:0:0:0: Attached scsi removable disk sdc [ 448.908000] sd 8:0:0:0: Attached scsi generic sg2 type 0 [ 448.908000] PM: Adding info for scsi:8:0:0:1 [ 448.916000] SCSI device sdd: 1984000 512-byte hdwr sectors (1016 MB) [ 448.916000] sdd: Write Protect is off [ 448.916000] sdd: Mode Sense: 02 00 00 00 [ 448.916000] sdd: assuming drive cache: write through [ 448.920000] SCSI device sdd: 1984000 512-byte hdwr sectors (1016 MB) [ 448.924000] sdd: Write Protect is off [ 448.924000] sdd: Mode Sense: 02 00 00 00 [ 448.924000] sdd: assuming drive cache: write through [ 448.924000] sdd: sdd1 [ 448.928000] sd 8:0:0:1: Attached scsi removable disk sdd [ 448.928000] sd 8:0:0:1: Attached scsi generic sg3 type 0 [ 448.928000] PM: Adding info for scsi:8:0:0:2 [ 448.936000] sd 8:0:0:2: Attached scsi removable disk sde [ 448.936000] sd 8:0:0:2: Attached scsi generic sg4 type 0 [ 448.936000] PM: Adding info for scsi:8:0:0:3 [ 448.940000] sd 8:0:0:3: Attached scsi removable disk sdf [ 448.940000] sd 8:0:0:3: Attached scsi generic sg5 type 0 [=========] An this is what lsusb shows: [=========] Bus 001 Device 003: ID 046d:c505 Logitech, Inc. Cordless Mouse+Keyboard Receiver Bus 001 Device 001: ID 0000:0000 Bus 002 Device 007: ID 07cc:0340 Carry Computer Eng., Co., Ltd Bus 002 Device 003: ID 058f:6387 Alcor Micro Corp. Bus 002 Device 001: ID 0000:0000 [=========] Tomorrow I'm going to temporarily remove the SATA drive that has Linux on it and put in a junky IDE and install XP,.. Just to see how the tuner device behaves with an alternate OS with the same hardware. Thanks, Jim..... ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Linux-usb-users@lists.sourceforge.net To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
